scholarly journals Analysis and Multi-Objective Optimization for Reducing Energy Consumption and Improving Surface Quality during Dry Machining of 304 Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4693
Author(s):  
Feilong Du ◽  
Lin He ◽  
Haisong Huang ◽  
Tao Zhou ◽  
Jinxing Wu
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Stainless Steel ◽  
Energy Consumption ◽  
Surface Quality ◽  
Feed Rate ◽  
Cutting Parameters ◽  
304 Stainless Steel ◽  
Multi Objective Optimization ◽  
Multi Objective

Cutting quality and production cleanliness are main aspects to be considered in the machining process, and determining the optimal cutting parameters is a significant measure to reduce energy consumption and optimize surface quality. In this paper, 304 stainless steel is adopted as the research objective. The regression models of the specific cutting energy, surface roughness, and microhardness are constructed and the inherent influence mechanism between cutting parameters and output responses are analyzed by analysis of variance (ANOVA). The desirability analysis method is introduced to perform the multi-objective optimization for low energy consumption (LEC) mode and low surface roughness (LSR) mode. Optimal combination of process parameters with composite desirability of 0.925 and 0.899 are obtained in such two modes respectively. As indicated by the results of multi-objective genetic algorithm (MOGA), genetic algorithm (GA) combined with weighted-sum-type objective function and experiment, the relative deviation values are within 10%. Moreover, the results also reveal that the feed rate is the most significant factor affecting the three responses, while the correlation of cutting depth is less noticeable. The effect of low feed rate on microhardness is primarily related to the mechanical load caused by extrusion, and the influence at high feed rate is determined by plastic deformation.

scholarly journals Prediction of Surface Roughness of 304 Stainless Steel and Multi-Objective Optimization of Cutting Parameters Based on GA-GBRT

2019 ◽  
Vol 9 (18) ◽  
pp. 3684 ◽  
Author(s):  
Tao Zhou ◽  
Lin He ◽  
Jinxing Wu ◽  
Feilong Du ◽  
Zhongfei Zou
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Quality ◽  
Regression Tree ◽  
Cutting Parameters ◽  
304 Stainless Steel ◽  
Gradient Boosting ◽  
Multi Objective Optimization ◽  
Multi Objective

Establishing and controlling the prediction model of a machined surface quality is known as the basis for sustainable manufacturing. An ensemble learning algorithm—the gradient boosting regression tree—is incorporated into the surface roughness modeling. In order to address the problem of a high time cost and tendency to fall into a local optimum solution when the grid search and conjugate gradient method is adopted to obtain the super-parameters of the ensemble learning algorithm, a genetic algorithm is employed to search for the optimal super-parameters in the training process, and a genetic-gradient boosting regression tree (GA-GBRT) algorithm is developed. A fitting goodness of fit is taken as the fitness function value of the genetic algorithm and combined with k-fold cross-validation, as such, the initial model parameters of the gradient boosting regression tree are optimized. Compared to the optimized artificial neural network (ANN) and support vector regression (SVR) and combined with the cutting experiment of 304 stainless steel with a micro-groove tool, a genetic algorithm multi-objective optimization model with the highest cutting efficiency and a supreme surface quality was constructed by applying the GA-GBRT model. The response relationship reveals the non-linear interaction that occurs between the cutting parameters and the surface roughness of 304 stainless steel that is machined by the micro-groove tool. As indicated by the results obtained from the multi-objective optimization, the cutting efficiency can be enhanced by increasing the cutting speed and depth within a small range of surface quality variations. The GA-GBRT model is validated to be reliable in making a prediction of the surface roughness and optimizing the cutting parameters with turning and milling data.

Research on Optimization of Cutting Parameters Based on Genetic Algorithm

2011 ◽  
Vol 121-126 ◽  
pp. 4640-4645 ◽  
Author(s):  
Shu Ren Zhang ◽  
Xue Guang Li ◽  
Jun Wang ◽  
Hui Wei Wang
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Surface Quality ◽  
Bp Neural Network ◽  
Prediction Method ◽  
Cutting Parameters ◽  
Multi Objective Optimization ◽  
Experiment Data ◽  
Optimization Of Cutting Parameters ◽  
Working Efficiency

Three elements of Cutting dosages have a great effect on parts surface quality and working efficiency, the best organization of cutting three elements for parts surface quality must be found before machining, in order to surface roughness and machining cost of parts, multi-objective optimization model is established in this paper, model is solved by using genetic algorithm. Based on the BP neural network of three layers, forecasting model of surface roughness is established. According to existing experiment data and optimized cutting dosages, analysis and prediction of surface roughness is done. Machining experiment is done by using optimized data. The experiment result verifies feasibility of this optimistic method and prediction method of surface roughness.

scholarly journals Multi-Objective Optimization of Turning Operation of Stainless Steel Using a Hybrid Whale Optimization Algorithm

2020 ◽  
Vol 4 (3) ◽  
pp. 64 ◽  
Author(s):  
Mahamudul Hasan Tanvir ◽  
Afzal Hussain ◽  
M. M. Towfiqur Rahman ◽  
Sakib Ishraq ◽  
Khandoker Zishan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Optimization Algorithm ◽  
Cutting Parameters ◽  
Whale Optimization Algorithm ◽  
Multi Objective Optimization ◽  
Turning Operation ◽  
Multi Objective ◽  
Whale Optimization ◽  
Optimum Cutting

In manufacturing industries, selecting the appropriate cutting parameters is essential to improve the product quality. As a result, the applications of optimization techniques in metal cutting processes is vital for a quality product. Due to the complex nature of the machining processes, single objective optimization approaches have limitations, since several different and contradictory objectives must be simultaneously optimized. Multi-objective optimization method is introduced to find the optimum cutting parameters to avoid this dilemma. The main objective of this paper is to develop a multi-objective optimization algorithm using the hybrid Whale Optimization Algorithm (WOA). In order to perform the multi-objective optimization, grey analysis is integrated with the WOA algorithm. In this paper, Stainless Steel 304 is utilized for turning operation to study the effect of machining parameters such as cutting speed, feed rate and depth of cut on surface roughness, cutting forces, power, peak tool temperature, material removal rate and heat rate. The output parameters are obtained through series of simulations and experiments. Then by using this hybrid optimization algorithm the optimum machining conditions for turning operation is achieved by considering unit cost and quality of production. It is also found that with the change of output parameter weightage, the optimum cutting condition varies. In addition to that, the effects of different cutting parameters on surface roughness and power consumption are analysed.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

scholarly journals Multi-Objective Optimization of Cutting Parameters in Turning AISI 304 Austenitic Stainless Steel

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 217 ◽  
Author(s):  
Yu Su ◽  
Guoyong Zhao ◽  
Yugang Zhao ◽  
Jianbing Meng ◽  
Chunxiao Li
Keyword(s):  
Energy Consumption ◽  
Cutting Parameters ◽  
Optimization Method ◽  
Multi Objective Optimization ◽  
Aisi 304 ◽  
Multi Objective ◽  
Relational Analysis ◽  
304 Austenitic Stainless Steel ◽  
Grey Relational ◽  
Optimization Of Cutting Parameters

Energy conservation and emission reduction is an essential consideration in sustainable manufacturing. However, the traditional optimization of cutting parameters mostly focuses on machining cost, surface quality, and cutting force, ignoring the influence of cutting parameters on energy consumption in cutting process. This paper presents a multi-objective optimization method of cutting parameters based on grey relational analysis and response surface methodology (RSM), which is applied to turn AISI 304 austenitic stainless steel in order to improve cutting quality and production rate while reducing energy consumption. Firstly, Taguchi method was used to design the turning experiments. Secondly, the multi-objective optimization problem was converted into a simple objective optimization problem through grey relational analysis. Finally, the regression model based on RSM for grey relational grade was developed and the optimal combination of turning parameters (ap = 2.2 mm, f = 0.15 mm/rev, and v = 90 m/s) was determined. Compared with the initial turning parameters, surface roughness (Ra) decreases 66.90%, material removal rate (MRR) increases 8.82%, and specific energy consumption (SEC) simultaneously decreases 81.46%. As such, the proposed optimization method realizes the trade-offs between cutting quality, production rate and energy consumption, and may provide useful guides on turning parameters formulation.

Multi Objective Optimization of Cutting Parameters in Machining Cellulose Based Hybrid Composites

2015 ◽  
Vol 761 ◽  
pp. 287-292
Author(s):  
Raja Izamshah ◽  
Zainudin Zuraidah ◽  
Mohd Shahir Kasim ◽  
M. Hadzley ◽  
M. Amran
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Hybrid Composites ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Multi Objective Optimization ◽  
Machining Performance ◽  
Machined Surface ◽  
Multi Objective ◽  
Optimization Of Cutting Parameters

Cellulose based hybrid composites are gaining popularity in the growing green communities. With extensive studies and increasing applications for future advancement, the need for an accurate and reliable guidance in machining this type of composites has increased enormously. Smooth and defect free machined surface are always the ultimate objectives. The present work deals with the study of machining parameters (i.e. spindle speed, feed rate and depth of cut) and their effects on machining performance (i.e. surface roughness and delamination) to establish an optimized setup of machining parameters in achieving multi objective machining performance. Cellulose based hybrid composites consist of jute (a bast fiber) and glass fiber embedded in polyester resins. Response Surface Methodology (RSM) using Box-Behnken Design (BBD) was chosen as the design of experiment approach for this study. Based on that experimental approach, 17 experimental runs were conducted. Mathematical model for each response was developed based on the experimental data. Adequacy of the models were analyzed statistically using Analysis of Variance (ANOVA) in determining the significant input variables and possible interactions. The multi objective optimization was performed through numerical optimization, and the predicted results were validated. The agreement between the experimental and selected solution was found to be strong, between 95% to 96%, thus validating the solution as the optimal machining condition. The findings suggest that feed rate was the main factor affecting surface roughness and delamination .

Sign in / Sign up

Export Citation Format

Share Document