scholarly journals Hysteretic Behavior of Geopolymer Concrete with Active Confinement Subjected to Monotonic and Cyclic Axial Compression: An Experimental Study

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 3997 ◽  
Author(s):  
Huailiang Wang ◽  
Yuhui Wu ◽  
Min Wei ◽  
Lang Wang ◽  
Baoquan Cheng
Keyword(s):  
Failure Modes ◽  
Peak Stress ◽  
Hysteretic Behavior ◽  
Stress And Strain ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Cyclic Compression ◽  
Stress States ◽  
Loading Modes ◽  
Good Agreement

This paper investigated the performance of actively confined geopolymer concrete (GPC) through experiments. The mechanical properties of GPC under triaxial stress states were analyzed and discussed from the prospects of failure modes, axial peak stress and strain, monotonic and cyclic constitutive relationships. The experimental results demonstrated that the loading modes (monotonic loading and cyclic loading) had little effect on the failure mode and axial peak stress and strain. The improvement of the strength and ductility of GPC with the increase in confinement level was consistent with that of the conventional cement concrete while the strain enhancement of confined GPC was lower than that of confined conventional cement concrete at the same confinement level. The curves of the monotonic stress–strain and the envelop of cyclic compression were predicted through Mander’s model with good accuracy. The unloading/reloading models proposed by Lokuge were modified and the predicted cyclic hysteresis curves for actively confined GPC were in good agreement with the cyclic compression results. Findings from this study provide references for the application of geopolymer concrete.

scholarly journals Triaxial Mechanical Properties and Micromechanism of Calcareous Sand Modified by Nanoclay and Cement

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Wei Wang ◽  
Jian Li ◽  
Jun Hu
Keyword(s):  
Mechanical Properties ◽  
Failure Modes ◽  
Peak Stress ◽  
Cement Composite ◽  
Friction Angle ◽  
Stress And Strain ◽  
Calcareous Sand ◽  
Marine Biological ◽  
Different Content ◽  
The Impact

Calcareous sand is developed by the fracture of marine biological skeleton under the impact of seawater. Calcareous sand is not transported in the process of deposition. Therefore, calcareous sand retains the characteristics of marine biological skeleton, low strength, and porous. In order to study the effect of nanoclay and cement on the modification of calcareous sand, a series of tests were carried out on the modified cement calcareous sand (CCS) with different content of nanoclay. In this study, the triaxial mechanical properties and failure modes of nanoclay and cement composite modified calcareous sand (NCCS) were studied through the triaxial UU test. Then, SEM tests were carried out on CCS and NCCS samples, and the micromechanism of nanoclay and cement composite modified Nanhai calcareous sand was analyzed. The results showed that (1) the shear properties of CCS could be improved by adding nanoclay. The optimum admixture ratio of nanoclay was 8%, and its peak stress was 23%-39% higher than that of CCS. (2) The peak stress and strain of NCCS showed a linear correlation. (3) Compared with CCS, the internal friction angle and cohesion of NCCS were increased by 5.2% and 52%, respectively. (4) Nanoclay could improve the compactness and structure of cement calcareous sand, and the macroscopic performance is the improvement of peak stress and cohesion.

scholarly journals An Extension Strain Type Mohr–Coulomb Criterion

2021 ◽  
Author(s):  
Manfred Staat
Keyword(s):  
Failure Modes ◽  
Peak Stress ◽  
Fracture Initiation ◽  
Failure Surface ◽  
Confining Pressure ◽  
Biaxial Compression ◽  
Simple Extension ◽  
Strain Criterion ◽  
Shear Component ◽  
Extension Strain

AbstractExtension fractures are typical for the deformation under low or no confining pressure. They can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. In this article, it is shown that the simple extension strain criterion makes unrealistic strength predictions in biaxial compression and tension. To overcome this major limitation, a new extension strain criterion is proposed by adding a weighted principal shear component to the simple criterion. The shear weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting extension failure modes, which are unexpected in the classical understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain leading to dilatancy. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak stress CP. Different from compressive loading, tensile loading requires only a limited number of critical cracks to cause failure. Therefore, for tensile stresses, the failure criteria must be modified somehow, possibly by a cut-off corresponding to the CI stress. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion.

scholarly journals Assimilation of Dynamic Combined Finite Discrete Element Methods Using the Ensemble Kalman Filter

2021 ◽  
Vol 11 (7) ◽  
pp. 2898
Author(s):  
Humberto C. Godinez ◽  
Esteban Rougier
Keyword(s):  
Kalman Filter ◽  
Ensemble Kalman Filter ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Peak Stress ◽  
Discrete Element ◽  
Material Behavior ◽  
Model Parameters ◽  
Hopkinson Pressure Bar ◽  
Parameter Values

Simulation of fracture initiation, propagation, and arrest is a problem of interest for many applications in the scientific community. There are a number of numerical methods used for this purpose, and among the most widely accepted is the combined finite-discrete element method (FDEM). To model fracture with FDEM, material behavior is described by specifying a combination of elastic properties, strengths (in the normal and tangential directions), and energy dissipated in failure modes I and II, which are modeled by incorporating a parameterized softening curve defining a post-peak stress-displacement relationship unique to each material. In this work, we implement a data assimilation method to estimate key model parameter values with the objective of improving the calibration processes for FDEM fracture simulations. Specifically, we implement the ensemble Kalman filter assimilation method to the Hybrid Optimization Software Suite (HOSS), a FDEM-based code which was developed for the simulation of fracture and fragmentation behavior. We present a set of assimilation experiments to match the numerical results obtained for a Split Hopkinson Pressure Bar (SHPB) model with experimental observations for granite. We achieved this by calibrating a subset of model parameters. The results show a steady convergence of the assimilated parameter values towards observed time/stress curves from the SHPB observations. In particular, both tensile and shear strengths seem to be converging faster than the other parameters considered.

Numerical Simulation of Ring-Shape Rock Failure under Compressive Loading

2011 ◽  
Vol 378-379 ◽  
pp. 15-18
Author(s):  
Yong Bin Zhang ◽  
Zheng Zhao Liang ◽  
Shi Bin Tang ◽  
Jing Hui Jia
Keyword(s):  
Numerical Simulation ◽  
Fracture Process ◽  
Failure Modes ◽  
Failure Process ◽  
Compressive Loading ◽  
Orientation Angle ◽  
Crack Orientation ◽  
Ring Specimen ◽  
Ring Shape ◽  
Good Agreement

In this paper, a ring shaped numerical specimen is used to studying the failure process in brittle materials. The ring specimen is subjected to a compressive diametral load and contains two angled central cracks. Numerical modeling in this study is performed. It is shown that the obtained numerical results are in a very good agreement with the experiments. Effect of the crack orientation angle on the failure modes and loading-displace responses is discussed. In the range of 0°~40°, the fracture paths are curvilinear forms starting from the tip of pre-existing cracks and grow towards the loading points. For the crack orientation angle 90°, vertical fractures will split the specimen and the horizontal cracks do not influence the fracture process.

Experimental and theoretical study of sandwich composites with Z-pins under quasi-static compression loading

2021 ◽  
pp. 136943322110073
Author(s):  
Erdem Selver ◽  
Gaye Kaya ◽  
Hussein Dalfi
Keyword(s):  
Vinyl Ester ◽  
Failure Modes ◽  
Critical Role ◽  
Sandwich Composites ◽  
Test Results ◽  
Compressive Properties ◽  
Element Analysis ◽  
Static Compression ◽  
Quasi Static Compression ◽  
Good Agreement

This study aims to enhance the compressive properties of sandwich composites containing extruded polystyrene (XPS) foam core and glass or carbon face materials by using carbon/vinyl ester and glass/vinyl ester composite Z-pins. The composite pins were inserted into foam cores at two different densities (15 and 30 mm). Compression test results showed that compressive strength, modulus and loads of the sandwich composites significantly increased after using composite Z-pins. Sandwich composites with 15 mm pin densities exhibited higher compressive properties than that of 30 mm pin densities. The pin type played a critical role whilst carbon pin reinforced sandwich composites had higher compressive properties compared to glass pin reinforced sandwich composites. Finite element analysis (FE) using Abaqus software has been established in this study to verify the experimental results. Experimental and numerical results based on the capabilities of the sandwich composites to capture the mechanical behaviour and the damage failure modes were conducted and showed a good agreement between them.

Improving the structural performance of reinforced geopolymer concrete incorporated with hazardous heavy metal waste ash

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Suresh Kumar Arunachalam ◽  
Muthukannan Muthiah ◽  
Kanniga Devi Rangaswamy ◽  
Arunkumar Kadarkarai ◽  
Chithambar Ganesh Arunasankar
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Medical Waste ◽  
Source Material ◽  
Geopolymer Concrete ◽  
Deformation Capacity ◽  
Cement Concrete ◽  
Content Type ◽  
Load Carrying ◽  
Reinforced Cement

Purpose Demand for Geopolymer concrete (GPC) has increased recently because of its many benefits, including being environmentally sustainable, extremely tolerant to high temperature and chemical attacks in more dangerous environments. Like standard concrete, GPC also has low tensile strength and deformation capacity. This paper aims to analyse the utilization of incinerated bio-medical waste ash (IBWA) combined with ground granulated blast furnace slag (GGBS) in reinforced GPC beams and columns. Medical waste was produced in the health-care industry, specifically in hospitals and diagnostic laboratories. GGBS is a form of industrial waste generated by steel factories. The best option to address global warming is to reduce the consumption of Portland cement production and promote other types of cement that were not a pollutant to the environment. Therefore, the replacement in ordinary Portland cement construction with GPC is a promising way of reducing carbon dioxide emissions. GPC was produced due to an alkali-activated polymeric reaction between alumina-silicate source materials and unreacted aggregates and other materials. Industrial pollutants such as fly ash and slag were used as raw materials. Design/methodology/approach Laboratory experiments were performed on three different proportions (reinforced cement concrete [RCC], 100% GGBS as an aluminosilicate source material in reinforced geopolymer concrete [GRGPC] and 30% replacement of IBWA as an aluminosilicate source material for GGBS in reinforced geopolymer concrete [IGRGPC]). The cubes and cylinders for these proportions were tested to find their compressive strength and split tensile strength. In addition, beams (deflection factor, ductility factor, flexural strength, degradation of stiffness and toughness index) and columns (load-carrying ability, stress-strain behaviour and load-deflection behaviours) of reinforced geopolymer concrete (RGPC) were studied. Findings As shown by the results, compared to Reinforced Cement Concrete (RCC) and 100% GGBS based Reinforced Geopolymer Concrete (GRGPC), 30% IBWA and 70% GGBS based Reinforced Geopolymer Concrete (IGRGPC) (30% IBWA–70% GGBS reinforced geo-polymer concrete) cubes, cylinders, beams and columns exhibit high compressive strength, tensile strength, flexural strength, load-carrying ability, ultimate strength, stiffness, ductility and deformation capacity. Originality/value All the results were based on the experiments done in this research. All the result values obtained in this research are higher than the theoretical values.

Biaxial Strength of HY 80 Steel

1985 ◽  
Vol 107 (2) ◽  
pp. 132-137 ◽  
Author(s):  
K. S. Chan ◽  
U. S. Lindholm ◽  
J. Wise
Keyword(s):  
Biaxial Tension ◽  
Strain Ratio ◽  
Thin Wall ◽  
Plastic Strain Ratio ◽  
Axial Tension ◽  
Diffuse Necking ◽  
Stress States ◽  
Von Mises ◽  
Tube Geometry ◽  
Good Agreement

The biaxial deformation behavior of HY 80 steel has been examined by testing thin wall tubes under combined axial tension and internal pressure. The effective stress-strain curves and the hardening response have been found to vary with the stress state. The plastic strain ratio at a given stress ratio deviates from the von Mises value except at the stress states near uniaxial tension, plane strain and equi-biaxial tension. Using Drucker theory, these deviations are eliminated and the resulting yield locus is in good agreement with both the Bishop-Hill theory and the experimental results. Influenced by the tube geometry, the instability strains at the onset of diffuse necking are decreased by an increase in hoop tension. The diffuse necking strains are reasonably predicted by the Swift and the Lankford-Saibel/Mellor criteria.

Sign in / Sign up

Export Citation Format

Share Document