scholarly journals Microstructure and Properties of the Copper Alloyed with Ag and Ti Powders Using Fiber Laser

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2430 ◽  
Author(s):  
Mariusz Krupiński ◽  
Paulina Ewelina Smolarczyk ◽  
Mirosław Bonek
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Chemical Composition ◽  
Abrasion Resistance ◽  
Melting Zone ◽  
Hardness Measurement ◽  
Copper Surface ◽  
Laser Alloying ◽  
Microstructure And Mechanical Properties ◽  
The Impact

The scope of the work covers the development of the relationship between the chemical composition of surface-modified copper and the diffusion of alloy elements as well as the microstructure and mechanical properties. This article presents the impact of laser alloying with titanium and silver powders on the microstructure and mechanical properties of copper. In order to investigate the phenomena occurring during the laser alloying process, microstructural studies were performed using scanning electron microscopy (SEM), optical microscopy, and energy dispersive x-ray spectroscopic (EDS) analysis of the chemical composition in micro-areas. In addition, to test the properties of the resulting alloy, abrasion resistance, hardness measurement at low loading force, and conductivity measurements were performed. As a result of alloying with Ag and Ti powders, three distinct zones were indeed recognized: re-melting zone (RZ), diffusion zone (DZ), and heat affected zone (HAZ). The surface modification that results from laser alloying increases the hardness as well as the abrasion resistance of the material. Overall, it was found that laser alloying with Ti powder increased the strength of the copper surface layer due to the formation of intermetallic phases (Cu3Ti2). It was also found that laser alloying with Ag powder changed the mechanical properties of the surface layer due to the solid solution strengthening.

scholarly journals Process Design Strategies for Producing Heavy Section Steel with Improved Quality

2013 ◽  
Vol 652-654 ◽  
pp. 988-991
Author(s):  
Jing Wei Zhao ◽  
Zheng Yi Jiang ◽  
Dong Bin Wei ◽  
Chong Soo Lee
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Longitudinal Direction ◽  
Ring Rolling ◽  
Design Strategies ◽  
Noticeable Effect ◽  
Heavy Section ◽  
Microstructure And Mechanical Properties ◽  
Impact Energies ◽  
The Impact

Uniformity of microstructure and mechanical properties is required for the heavy section steel. In the present work, a heavy section wind tower flange was manufactured by controlled ring-rolling. Post-rolling heat treatment was employed to optimize the microstructure and mechanical properties. The chemical composition, microstructure and mechanical properties in different zones of the flange were investigated. The results showed that the chemical composition and microstructure were uniformly distributed in the flange. The tensile strength showed similar values in different sampling locations. The strain and impact energies of specimens prepared along the longitudinal direction were higher than that prepared along both the radius and thickness directions. Notch direction did not have noticeable effect on the impact energy. It is demonstrated that the designed process is effective for producing heavy section steel with improved quality.

Microstructure and Properties of the Aluminum Alloyed with ZrO Powder Using Fiber Laser

2021 ◽  
Vol 326 ◽  
pp. 157-165
Author(s):  
Paulina Smolarczyk ◽  
Mariusz Krupiński ◽  
Wojciech Pakieła
Keyword(s):  
Mechanical Properties ◽  
Abrasion Resistance ◽  
Load Force ◽  
Pure Aluminium ◽  
Laser Alloying ◽  
Low Load ◽  
Surface Modified ◽  
The Impact ◽  
The Relationship ◽  
Microstructural Studies

The scope of the work covers the development of the relationship between the chemical composition of surface-modified aluminium and its mechanical properties. This article presents the impact of laser alloying with ZrO powder on the microstructure and mechanical properties of pure aluminium. In order to study the phenomena occurring during the laser alloying process, microstructural studies were carried out using optical microscopy. Additionally, the properties of the obtained alloy were tested - abrasion resistance and hardness measured at low load force. As a result of the alloying process, three distinct zones were identified: the remelting zone (RZ), the diffusion zone (DZ) and the heat affected zone (HAZ). The surface modification resulting from laser alloying increases the hardness and abrasion resistance of the material.

Analysis of the microstructure and properties of T92 steel after long-term service

2018 ◽  
Vol 1 (93) ◽  
pp. 5-11
Author(s):  
A. Merda ◽  
K Klimaszewska ◽  
M. Sroka ◽  
P. Wieczorek ◽  
G. Golański
Keyword(s):  
Mechanical Properties ◽  
Hardness Measurement ◽  
Steam Superheater ◽  
Martensitic Steels ◽  
Precipitate Morphology ◽  
Microstructural Investigation ◽  
Microstructure And Mechanical Properties ◽  
Static Tensile ◽  
The Impact

Purpose: The purpose of the investigation was to determine and analyse the changes in the microstructure and mechanical properties of the T92 steel after service in creep conditions of the following parameters: temperature – 575°C, pressure – 28.2 MPa, service time – 41914 hrs. Design/methodology/approach: The tests were performed on the test samples taken from a pipe section of a steam superheater after long-term service. The range of the investigations included: microstructural investigation – the optical and SEM microscopy, the analysis of precipitation – carbide isolates, the investigation of mechanical properties: the Vickers hardness measurement, the impact test and static tensile test. Findings: The performed tests showed a slight degree of exhaustion of the structure of the analysed T92 steel. The relatively small changes in the microstructure of the examined steel were reflected in the still retained high mechanical properties. Research limitations/implications: he analysis of the microstructure of the examined steel using SEM was performed to determine the influence of the service on the processes of changes in the precipitate morphology. Practical implications: The metal science investigation of the sections taken from the elements of the power installations after long-term service is one of the basic elements of building the data base of materials and their joints used in the power industry. The results obtained from the performed research constitute a building block for the degradation characteristics of the microstructure and mechanical properties of martensitic steels of the 9-12%Cr type. Originality/value: The results of investigation and analysis of the metallographic and mechanical properties of martensitic T92 steel after long-term service are presented.

scholarly journals Microstructure and Mechanical Properties of Heat-Affected Zone of Repeated Welding AISI 304N Austenitic Stainless Steel by Gleeble Simulator

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 773
Author(s):  
Y.H. Guo ◽  
Li Lin ◽  
Donghui Zhang ◽  
Lili Liu ◽  
M.K. Lei
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Energy ◽  
Heat Affected Zone ◽  
Ferrite Content ◽  
Equipment Safety ◽  
Microstructure And Mechanical Properties ◽  
Δ Ferrite ◽  
The Impact

Heat-affected zone (HAZ) of welding joints critical to the equipment safety service are commonly repeatedly welded in industries. Thus, the effects of repeated welding up to six times on the microstructure and mechanical properties of HAZ for AISI 304N austenitic stainless steel specimens were investigated by a Gleeble simulator. The temperature field of HAZ was measured by in situ thermocouples. The as-welded and one to five times repeated welding were assigned as-welded (AW) and repeated welding 1–5 times (RW1–RW5), respectively. The austenitic matrices with the δ-ferrite were observed in all specimens by the metallography. The δ-ferrite content was also determined using magnetic and metallography methods. The δ-ferrite had a lathy structure with a content of 0.69–3.13 vol.%. The austenitic grains were equiaxial with an average size of 41.4–47.3 μm. The ultimate tensile strength (UTS) and yield strength (YS) mainly depended on the δ-ferrite content; otherwise, the impact energy mainly depended on both the austenitic grain size and the δ-ferrite content. The UTS of the RW1–RW3 specimens was above 550 MPa following the American Society of Mechanical Engineers (ASME) standard. The impact energy of all specimens was higher than that in ASME standard at about 56 J. The repeated welding up to three times could still meet the requirements for strength and toughness of welding specifications.

The Effect of Aging Heat Treatment on the Microstructure and Mechanical Properties of 10Cr20Ni25Mo1.5NbN Austenitic Steel

2016 ◽  
Vol 35 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Zhiyuan Liang ◽  
Wanhua Sha ◽  
Qinxin Zhao ◽  
Chongbin Wang ◽  
Jianyong Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Austenitic Steel ◽  
Treatment Time ◽  
Aging Treatment ◽  
Secondary Phases ◽  
Aging Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
The Impact

AbstractThe effect of aging heat treatment on the microstructure and mechanical properties of 10Cr20Ni25Mo1.5NbN austenitic steel was investigated in this article. The microstructure was characterized by scanning electron microscopy, energy dispersive spectrometry and transmission electron microscopy. Results show that the microstructure of 10Cr20Ni25Mo1.5NbN austenitic is composed of austenite. This steel was strengthened by precipitates of secondary phases that were mainly M23C6 carbides and NbCrN nitrides. As aging treatment time increased, the tensile strength first rose (0–3,000 h) and then fell (3,000–5,000 h) due to the decrease of high density of dislocations. The impact absorbed energy decreased sharply, causing the sulfides to precipitate at the grain boundary. Therefore, the content of sulfur should be strictly controlled in the steelmaking process.

scholarly journals Microstructure and Mechanical Properties of Modern 11%Cr Heat-Resistant Steel Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3430
Author(s):  
Grzegorz Golański ◽  
Jacek Słania ◽  
Marek Sroka ◽  
Paweł Wieczorek ◽  
Michał Urzynicok ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Martensitic Steel ◽  
Base Material ◽  
Hardness Measurement ◽  
Power Industry ◽  
Strength Properties ◽  
Typical Structure ◽  
Δ Ferrite ◽  
The Impact

In addition to good high-temperature creep resistance and adequate heat resistance, steels for the power industry must have, among other things, good weldability. Weldability of such steels is one of the criteria determining whether or not the material is suitable for applications in the power industry. Therefore, when materials such as martensitic steel Thor 115 (T115) are introduced into the modern power industry, the quality and properties of welded joints must be assessed. The paper presents the results of metallographic and mechanical investigations of T115 martensitic steel welded joints. The analysis was carried out on joints welded with two filler metals: WCrMo91 (No. 1) and EPRI P87 (No. 2). The scope of the investigations included: microstructural investigations carried out using optical, scanning and transmission electron microscopy and mechanical testing, i.e., Vickers microhardness and hardness measurement, static tensile test and impact test. The macro- and microstructural investigations revealed correct structure of the weld, without welding imperfections. The microstructural investigations of joint No. 1 revealed a typical structure of this type of joint, i.e., the martensitic structure with numerous precipitates, while in joint No. 2, the so-called Nernst’s layers and δ-ferrite patches were observed in the weld fusion zone as well as the heat affected zone (HAZ). The mechanical properties of the test joints met the requirements for the base material. A slight influence of the δ-ferrite patch on the strength properties of joint No. 2 was observed, and its negative effect on the impact energy of HAZ was visible.

scholarly journals Microstructure and Mechanical Properties of 14Cr-ODS Steels with Zr Addition

2019 ◽  
Vol 38 (2019) ◽  
pp. 404-410 ◽  
Author(s):  
Weijuan Li ◽  
Haijian Xu ◽  
Xiaochun Sha ◽  
Jingsong Meng ◽  
Zhaodong Wang
Keyword(s):  
Mechanical Properties ◽  
Hot Isostatic Pressing ◽  
Oxide Dispersion Strengthened ◽  
Nominal Composition ◽  
Ods Steel ◽  
Zr Addition ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Ods Steels ◽  
The Impact

AbstractIn this study, oxide dispersion strengthened (ODS) ferritic steels with nominal composition of Fe–14Cr–2W–0.35Y2O3 (14Cr non Zr-ODS) and Fe–14Cr–2W–0.3Zr–0.35Y2O3 (14Cr–Zr-ODS) were fabricated by mechanical alloying (MA) and hot isostatic pressing (HIP) technique to explore the impact of Zr addition on the microstructure and mechanical properties of 14Cr-ODS steels. Microstructure characterization revealed that Zr addition led to the formation of finer oxides, which was identified as Y4Zr3O12, with denser dispersion in the matrix. The ultimate tensile strength (UTS) of the non Zr-ODS steel is about 1201 MPa, but UTS of the Zr-ODS steel increases to1372 MPa, indicating the enhancement of mechanical properties by Zr addition.

scholarly journals Influence of Vanadium on the Microstructure and Mechanical Properties of Medium-Carbon Steels for Wheels

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 978 ◽  
Author(s):  
Pengfei Wang ◽  
Zhaodong Li ◽  
Guobiao Lin ◽  
Shitong Zhou ◽  
Caifu Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Grain Refinement ◽  
Carbon Steels ◽  
Precipitation Strengthening ◽  
Austenite Grain Size ◽  
Medium Carbon ◽  
Microstructure And Mechanical Properties ◽  
Medium Carbon Steels ◽  
The Impact

Steels used for high-speed train wheels require a combination of high strength, toughness, and wear resistance. In 0.54% C-0.9% Si wheel steel, the addition of 0.075 or 0.12 wt % V can refine grains and increase the ferrite content and toughness, although the influence on the microstructure and toughness is complex and poorly understood. We investigated the effect of 0.03, 0.12, and 0.23 wt % V on the microstructure and mechanical properties of medium-carbon steels (0.54% C-0.9% Si) for train wheels. As the V content increased, the precipitation strengthening increased, whereas the grain refinement initially increased, and then it remained unchanged. The increase in strength and hardness was mainly due to V(C,N) precipitation strengthening. Increasing the V content to 0.12 wt % refined the austenite grain size and pearlite block size, and increased the density of high-angle ferrite boundaries and ferrite volume fraction. The grain refinement improved the impact toughness. However, the impact toughness then reduced as the V content was increased to 0.23 wt %, because grain refinement did not further increase, whereas precipitation strengthening and ferrite hardening occurred.

scholarly journals The impact of the top coating on the mechanical properties of lacquered wood surfaces

2012 ◽  
pp. 87-100
Author(s):  
Milan Jaic ◽  
Tanja Palija
Keyword(s):  
Mechanical Properties ◽  
Wood Species ◽  
Abrasion Resistance ◽  
Direct Contact ◽  
Quercus Robur ◽  
Scratch Resistance ◽  
Indentation Hardness ◽  
Polyurethane Coating ◽  
The Impact ◽  
Wood Surfaces

This paper investigates the impact of the top coating on the basic mechanical properties of a lacquered surface, including indentation hardness, scratch resistance and abrasion resistance. Three types of the top coating were used, including a 2K polyurethane coating, a 2K acrylate-isocyanate coating and a 2K alkyd-urethane coating. Samples of two wood species, spruce (Picea abies Karst.) and oak (Quercus robur L.), were used in this study, in order to determine whether the wood species, which is not in direct contact with the top coating, has an impact on the mechanical properties of a lacquered surface. The samples coated with a 2K acrylate-isocyanate coating showed the highest values of indentation hardness, in the samples of both wood species (1.34 N for spruce; 1.4 N for oak). The samples coated with a 2K alkyd-urethane coating showed the highest values of scratch resistance (20 N for both wood species) and abrasion resistance (mass loss of 480 mg after 700 cycles for both wood species). The results have shown that the wood species does not affect the value of indentation hardness, scratch resistance and abrasion resistance of a lacquered surface.

Microstructure and Mechanical Properties of Al-12.6%Si Composite Reinforced by Al63Cu25Fe12Quasicrystal

2012 ◽  
Vol 182-183 ◽  
pp. 162-166
Author(s):  
Can Can Li ◽  
Hao Ran Geng ◽  
Zhen Yuan Li ◽  
Hai Ou Qin
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Cooling Rate ◽  
Quasicrystalline Phase ◽  
Melt Temperature ◽  
Microstructure And Mechanical Properties

In this paper, Al-12.6%Si/Al63Cu25Fe12 composites were fabricated by method of casting. The microstructure and chemical composition of Al63Cu25Fe12 quasicrystal alloy and Al-12.6%Si alloy reinforced by the quasicrystal were studied, and the mechanical properties of Al-12.6%Si composite were also measured. The results show that almost single quasicrystalline phases exist in the samples which are cast with the 1300°C melt. Quickly enough cooling rate and appropriate melt temperature are necessary for the formation of the quasicrystalline phase. In addition, Al-12.6%Si composite has optimal mechanical properties when the amount of Al63Cu25Fe12 quasicrystal is 3 wt%.

Sign in / Sign up

Export Citation Format

Share Document