scholarly journals Effect of FSW Traverse Speed on Mechanical Properties of Copper Plate Joints

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1937 ◽  
Author(s):  
Tomasz Machniewicz ◽  
Przemysław Nosal ◽  
Adam Korbel ◽  
Marek Hebda
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rolling Direction ◽  
Base Material ◽  
Traverse Speed ◽  
Travel Speed ◽  
Fatigue Tests ◽  
Copper Plate ◽  
Friction Stir ◽  
Microstructural Evaluation

The paper describes the influence of the friction stir welding travel speed on the mechanical properties of the butt joints of copper plates. The results of static and fatigue tests of the base material (Cu-ETP R220) and welded specimens produced at various travel speeds were compared, considering a loading applied both parallel and perpendicularly to the rolling direction of the plates. The mechanical properties of the FSW joints were evaluated with respect to parameters of plates’ material in the delivery state and after recrystallisation annealing. The strength parameters of friction stir welding joints were compared with the data on tungsten inert gas welded joints of copper plates available in the literature. The results of microhardness tests and fractographic analysis of tested joints are also presented. Based on the above test results, it was shown that although in the whole range of considered traverse speeds (from 40 to 80 mm/min), comparable properties were obtained for FSW copper joints in terms of their visual and microstructural evaluation, their static and especially fatigue parameters were different, most apparent in the nine-fold greater observed average fatigue life. The fatigue tests turned out to be more sensitive criteria for evaluation of the FSW joints’ qualities.

Microstructure and Mechanical Properties of Cu-Cr-Zr Alloy by Friction Stir Welding

2012 ◽  
Vol 602-604 ◽  
pp. 608-611
Author(s):  
Di Qiu He ◽  
Rui Lin Lai ◽  
Shao Hua Xu ◽  
Kun Yu Yang ◽  
Shao Yong Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Base Material ◽  
Traverse Speed ◽  
Nugget Zone ◽  
Alloy Plate ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Zr Alloy

In this study, Cu-Cr-Zr alloy joints are successfully fabricated by friction stir welding (FSW). Defect-free weld are produced on 12mm thick Cu-Cr-Zr alloy plate useing a non-consumable tool with a specially designed and shoulder with a constant rotation speed and a fixed traverse speed. The effect of friction stir welding (FSW) on the microstructure and mechanical properties of Cu-Cr-Zr alloy joints are investigated in details: The joints showed the presence of various zones such as nugget zone (NZ) and thermo-mechanically affected zone (TMAZ) and base metal (BM), the microhardness and the tensile strength of welded joints are lower than that of the base material.

scholarly journals Influence of Mx-Trivex, A-Skew, Three Flat Threaded and Concave Shouldered Mx-Triflute Tool Pin Profiles on Tensile Properties and Fractural Behaviour of Aa 6082-T6 Weldments During Friction Stir Welding

2020 ◽  
Vol 9 (4) ◽  
pp. 1376-1384
Keyword(s):  
Friction Stir Welding ◽  
Tensile Test ◽  
Weld Zone ◽  
Base Material ◽  
Traverse Speed ◽  
Friction Stir ◽  
Tool Pin ◽  
Solid State Joining ◽  
Joining Process ◽  
Brass Wire

Friction Stir Welding (FSW) is a topical and propitious solid-state joining process producing economical and strengthened joints of age-hardened and heat-treatable Aluminium Alloy AA 6082-T6. Mechanical and fractural behaviour of weldments were investigated in order to find crack initiation and necking on the weld zone thereby perceiving the complete behaviour of fracture occurred near the weld zone. Weldments are fabricated by employing four tool pin profiles namely MX-TRIVEX, A-SKEW, Three flat threaded and Concave shouldered MX-TRIFLUTE tools at various rotational speeds 1000 rpm, 1200 rpm and 1400 rpm at single traverse speed 25 mm/min. EXCETEX-EX-40 CNC wire cut EDM with 0.25 mm brass wire diameter has been employed to perform the extraction of tensile test specimens from the weldments according to ASTM E8M-04 standard. Tensile test was performed on elctromechanically servo controlled TUE-C-200 (UTM machine) according to ASTM B557-16 standards Maximum Ultimate Tensile Strength (UTS) of 172.33 MPa (55.5% of base material) and 0.2% Yield Stress (YS) of 134.10 MPa (51.5% of base material) were obtained by using A-SKEW at 1400 rpm, 25 mm/min and maximum % Elongation (%El) of 11.33 (113.3% of base material) was obtained at MX-TRIVEX at 1000 rpm, 25 mm/min. Minimum UTS of 131.16 MPa (42.30% of base material) and 0.2% YS of 105.207 MPa (40.46% of base material )were obtained by using Concave shouldered MX-TRIFLUTE at 1400 rpm, 25 mm/min. Minimum % El of 5.42 ( 54.2% of base material) was obtained by using A-SKEW at 1000 rpm, 25 mm/min.

Microhardness and Microstructural Studies on Underwater Friction Stir Welding of 5052 Aluminum Alloy

2017 ◽  
Author(s):  
Srinivasa Rao Pedapati ◽  
Dhanis Paramaguru ◽  
Mokhtar Awang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Plate Thickness ◽  
Base Material ◽  
Friction Stir ◽  
Underwater Friction Stir Welding ◽  
Void Area ◽  
Average Size ◽  
Microstructural Studies

As compared to normal Friction Stir Welding (FSW) joints, the Underwater Friction Stir Welding (UFSW) has been reported to be obtainable in consideration of enhancement in mechanical properties. A 5052-Aluminum Alloy welded joints using UFSW method with plate thickness of 6 mm were investigated, in turn to interpret the fundamental justification for enhancement in mechanical properties of material through UFSW. Differences in microstructural features and mechanical properties of the joints were examined and discussed in detail. The results indicate that underwater FSW has reported lower hardness value in the HAZ and higher hardness value in the intermediate of stir zone (SZ). The average hardness value of underwater FSW increases about 53% greater than its base material (BM), while 21% greater than the normal FSW. The maximum micro-hardness value was three times greater than its base material (BM), and the mechanical properties of underwater FSW joint is increased compared to the normal FSW joint. Besides, the evaluated void-area fraction division in the SZ of underwater FSW joint was reduced and about one-third of the base material (BM). The approximately estimated average size of the voids in SZ of underwater FSW also was reduced to as low as 0.00073 mm2, when compared to normal FSW and BM with approximately estimated average voids size of 0.0024 mm2 and 0.0039 mm2, simultaneously.

scholarly journals Research on the Friction Stir Welding of Sc-Modified AA2519 Extrusion

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1024 ◽  
Author(s):  
Robert Kosturek ◽  
Lucjan Śnieżek ◽  
Janusz Torzewski ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Base Material ◽  
Stir Zone ◽  
Welding Parameters ◽  
Friction Stir ◽  
Treated Condition ◽  
Heat Treated ◽  
Heat Treated Condition ◽  
Fsw Parameters

The aim of this research was to investigate the effect of friction stir welding (FSW) parameters on microstructure and mechanical properties of Sc-modified AA2519 extrusion joints. The workpiece was welded by FSW in non-heat-treated condition with seven different sets of welding parameters. For each obtained joint macrostructure and microstructure observations were performed. Mechanical properties of joints were investigated using tensile test together with localization of fracture location. Joint efficiencies were established by comparing measured joints tensile strength to the value for base material. The obtained results show that investigated FSW joints of Sc-modified AA2519 in the non-heat-treated condition have joint efficiency within the range 87–95%. In the joints obtained with the lowest ratio of the tool rotation speed to the tool traverse speed, the occurrence of imperfections (voids) localized in the stir zone was reported. Three selected samples were subjected to further investigations consisting microhardness distribution and scanning electron microscopy fractography analysis. As the result of dynamic recrystallization, the microhardness of the base material value of 86 HV0.1 increased to about 110–125 HV0.1 in the stir zone depending on the used welding parameters. Due to lack of the strengthening phase and low strain hardening of used alloy the lack of a significantly softened zone was reported by both microhardness analysis and investigation of the fractured samples.

Fatigue Properties of Al-Li Plates Joined by Friction Stir Welding

2008 ◽  
Vol 385-387 ◽  
pp. 849-852 ◽  
Author(s):  
Pasquale Cavaliere ◽  
Francesco W. Panella ◽  
Antonio Squillace
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Testing Machine ◽  
Rolling Direction ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Control Mode ◽  
Fatigue Properties ◽  
Amplitude Control ◽  
Friction Stir

Al-Li alloys are characterized by a strong anisotropy in mechanical properties and microstructure with respect to the rolling direction. Plates of 2198 Al-Li alloy were friction stir welded by employing maximum rotation speed: 1000 rev/min and welding speed of 80 mm/min, both in parallel and orthogonal directions with respect to the rolling one. The joints mechanical properties were evaluated by means of tensile tests at room temperature. In addition, fatigue tests performed with a resonant electro-mechanical testing machine under constant amplitude control up to 250 Hz loading, were conducted in axial control mode with R(σmin/σmax)=0.33, for all the welding and rotating speed conditions. The fatigue crack propagation experiments were performed by employing single edge notched specimens.With the aim to characterize the weld performances, both the microstructure evolution at jointed cross sections, related to the welding variables, and the fractured surfaces were respectively analyzed by means of optical and scanning electron microscopy.

Evaluation of dissimilar joints properties of 5083-H12 and 6061-T6 aluminum alloys produced by tungsten inert gas and friction stir welding

2015 ◽  
Vol 231 (3) ◽  
pp. 297-308 ◽  
Author(s):  
Morteza Ghaffarpour ◽  
Mohammad Kazemi ◽  
Mohammad Javad Mohammadi Sefat ◽  
Ahmad Aziz ◽  
Kamran Dehghani
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Traverse Speed ◽  
Inert Gas ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys ◽  
The Difference ◽  
Welding Processes

In the present study, friction stir welding (FSW) and tungsten inert gas (TIG) techniques were used to join the dissimilar aluminum alloys of 5083-H12 and 6061-T6. The laboratory tests were designed using design of experiment (DOE) method. Variables for the FSW process were the rotational speed, traverse speed, shoulder diameter, and pin diameter. They changed in ranges of 700–2500 r/min, 25–400 mm/min, 10–14 mm, and 2–4 mm, respectively. In the case of TIG process, the variables were current intensity, traverse speed, and tilt angle. These parameters varied from 80 to 90 A, 200 to 400 mm/min, and 3° to 12°, respectively. The optimum amounts of parameters were obtained using response surface methodology (RSM). The RSM-based model was developed to predict ultimate tensile strength (UTS) of the welds produced. In FSW, the difference between predicted and measured UTS was about 1.28% and in TIG it was 1.78%. The good agreement between experimental and predicted results indicates the high accuracy of the developed model. Mechanical properties and also the microstructure of the welds were compared after optimizing both welding processes using RSM. The results showed that the welds produced by FSW indicated a considerably higher quality and also improved mechanical properties compared to TIG. Properties of the joints obtained by FSW in single-sided joints were more desirable. In the double-sided welds obtained by FSW these differences were of an even higher significance.

An investigation on the mechanical properties of friction stir welded polycarbonate/aluminium oxide nanocomposite sheets

2016 ◽  
Vol 49 (6) ◽  
pp. 498-512 ◽  
Author(s):  
Ali Doniavi ◽  
Saeedeh Babazadeh ◽  
Taher Azdast ◽  
Rezgar Hasanzadeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Rotational Speed ◽  
Signal To Noise Ratio ◽  
Base Material ◽  
Travel Speed ◽  
Effective Parameter ◽  
Welding Parameters ◽  
Effective Parameters ◽  
Friction Stir

Although considerable progress has been made in recent years in field of polymer welding, challenges still remain in using a friction stir welding method to join polycarbonate (PC) composites. This research provides an investigation on the effect of welding parameters (tool’s travel and rotational speeds) on mechanical properties of PC nanocomposite weld lines. PC nanocomposites were prepared with different percentages of Al2O3 nanofiller using a twin screw extruder and injection moulded as sheets in order to ease the welding. Considering various parameters and their levels, optimization of Taguchi experimental design was carried out, an L16 orthogonal standard array was selected and the effective parameter was calculated using analysis of variance of the results. The results indicated that nanoalumina percentage is the most effective parameter on the tensile strength of weld and tool’s travel speed and rotational speed are next effective parameters, respectively. According to signal-to-noise ratio, maximum weld tensile strength (89.5% of base material) is revealed when nanoalumina percentage, tool’s travel speed and tool’s rotational speed were chosen as 1 wt%, 12 mm/min and 1250 r/min, respectively.

Investigation of Microstructure and Mechanical Properties of Friction Stir Lap Jointed Ni Base Superalloy

2012 ◽  
Vol 724 ◽  
pp. 481-485
Author(s):  
Kuk Hyun Song ◽  
Kazuhiro Nakata
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Friction Stir Welding ◽  
Base Material ◽  
Lap Joints ◽  
Stir Zone ◽  
Inconel 600 ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

This study evaluated the microstructure and mechanical properties of friction stir welded lap joints. Inconel 600 and SS 400 as experimental materials were selected, and friction stir welding was carried out at tool rotation speed of 200 rpm and welding speed of 100 mm/min. Applying the friction stir welding was notably effective to reduce the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. Joint interface between Inconel 600 and SS 400 showed a sound weld without voids and cracks. Also, the hook, along the Inconel 600 alloy from SS 400, was formed at advancing side, which directly affected an increase in peel strength. In this study, we systematically discussed the evolution on microstructure and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.

scholarly journals Investigation of microstructural and mechanical properties of AA1050-AZ91D dissimilar friction stir welding

2021 ◽  
Vol 15 (3) ◽  
pp. 8332-8343
Author(s):  
Oyindamola Kayode ◽  
Esther Titilayo Akinlabi
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Solid State ◽  
Chemical Properties ◽  
Traverse Speed ◽  
Friction Stir ◽  
Microhardness Distribution ◽  
Dissimilar Weld ◽  
State Diffusion ◽  
Dissimilar Friction Stir Welding

Joining of aluminium and magnesium alloys frequently pose significant challenges to the extent where joining may seem impossible, due to differences in the physical, metallurgical, and chemical properties of the materials. Friction stir welding is a solid-state welding technique which uses a non-consumable tool to join metals. This study examines the dissimilar friction stir welding of 3 mm thick AA1050 and AZ91D alloy sheets. Successful defect-free joints were achieved at rotational speeds of 400 rpm and 600 rpm, and a constant traverse speed of 50 mm/min. The metallurgical investigations used to characterize the microstructure of the welds are optical microscopy (OM), scanning electron microscope (SEM) and X-ray diffraction (XRD). The microstructures of the samples show distinct morphology attributed to their different rotational speeds. However, Al3Mg2 intermetallics (IMCs) phase was detected in the white bands present in both weld samples. The IMCs were formed through solid-state diffusion. The mechanical properties characterizations includes the microhardness profiles and tensile testing. The variation in the rotational speeds do not have a significant effect on the microhardness distribution of the weld samples. The tensile strength of the dissimilar weld improved substantially with the presence of an interpenetration feature (IPF).

Sign in / Sign up

Export Citation Format

Share Document