scholarly journals Effect of Soda Residue Addition and Its Chemical Composition on Physical Properties and Hydration Products of Soda Residue-Activated Slag Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1789 ◽  
Author(s):  
Yonghui Lin ◽  
Dongqiang Xu ◽  
Xianhui Zhao
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Cementitious Materials ◽  
Aluminum Silicate ◽  
Chemical Components ◽  
Main Role ◽  
Hydration Products ◽  
Granulated Blast Furnace Slag ◽  
Activated Slag ◽  
Main Components

Soda residue (SR), the solid waste of Na2CO3 produced by ammonia soda process, pollutes water and soil, increasing environmental pressure. SR has high alkalinity, and its main components are Ca(OH)2, NaCl, CaCl2, CaSO4, and CaCO3, which accords with the requirements of being an alkali activator. The aim of this research is to investigate the best proportion of SR addition and the contribution of individual chemical components in SR to SR- activated ground granulated blast furnace slag (GGBS) cementitious materials. In this paper, GGBS pastes activated by SR, Ca(OH)2, Ca(OH)2 + NaCl, Ca(OH)2 + CaCl2, Ca(OH)2 + CaSO4, and Ca(OH)2 + CaCO3 were studied regarding setting time, compressive strength (1 d, 3 d, 7 d, 14 d, 28 d), hydration products, and microstructure. The results demonstrate that SR (24%)-activated GGBS pastes possess acceptable setting time and compressive strength (29.6 MPa, 28 d), and its hydration products are calcium silicate hydrate (CSH) gel, calcium aluminum silicate hydrates (CASH) gel and Friedel’s salt. CaCl2 in SR plays a main role in hydration products generation and high compressive strength of SR- activated GGBS pastes.

scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

Influence of Triethanolamine on the Properties of Cement-Based Materials

2017 ◽  
Vol 898 ◽  
pp. 2010-2017 ◽  
Author(s):  
Xiao Ying Wang ◽  
Ming Zhang Lan ◽  
Wei Fang Hou ◽  
Bin Feng Xiang ◽  
Xu Dong Zhao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Hydration ◽  
Setting Time ◽  
Cementitious Materials ◽  
Hydration Products ◽  
Initial Setting Time ◽  
Final Setting Time ◽  
Retarding Effect ◽  
Initial Setting

The effects of triethanolamine on the compressive strength and setting time of fly ash cementitious materials, slag cementitious materials, and limestone cementitious materials were investigated. The results show that the dosage of 0.04% of triethanolamine can significantly improve the 3d, 7d and 28d compressive strength of fly ash cementitious materials. It possesses less impact on the setting time. The dosage of 0.04% of triethanolamine can significantly improve the 3d and 7d compressive strength of slag cementitious materials while the effect of late strength is not obvious. It extends the initial setting time and the final setting time is not changed, which has retarding effect. The results of hydration heat and XRD show that triethanolamine extends the induction period of cement hydration, and gypsum is exhausted in advance during the hydration process. Triethanolamine promotes the transformation of AFt to AFm and there is no effect on the type of hydration products.

scholarly journals Influence of Na2O Content and Ms (SiO2/Na2O) of Alkaline Activator on Workability and Setting of Alkali-Activated Slag Paste

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2072 ◽  
Author(s):  
Sung Choi ◽  
Kwang-Myong Lee
Keyword(s):  
Setting Time ◽  
High Strength ◽  
Abrupt Decrease ◽  
Na2o Content ◽  
Alkali Activated Slag ◽  
Granulated Blast Furnace Slag ◽  
Type Composition ◽  
Activated Slag ◽  
Binary Alkaline ◽  
Alkali Activated

The performance of alkali-activated slag (AAS) paste using activators of strong alkali components is affected by the type, composition, and dosage of the alkaline activators. Promoting the reaction of ground granulated blast furnace slag (GGBFS) by alkaline activators can produce high-strength AAS concrete, but the workability might be drastically reduced. This study is aimed to experimentally investigate the heat release, workability, and setting time of AAS pastes and the compressive strength of AAS mortars considering the Na2O content and the ratio of Na2O to SiO2 (Ms) of binary alkaline activators blended with sodium hydroxide and sodium silicate. The test results indicated that the AAS mortars exhibited a high strength of 25 MPa at 24 h, even at ambient temperature, even though the pastes with an Na2O content of ≥6% and an Ms of ≥1.0 exhibited an abrupt decrease in flowability and rapid setting.

Experimental Study on Alkali-Activated Slag-Lithium Slag-Fly Ash Environmental Concrete

2011 ◽  
Vol 287-290 ◽  
pp. 1237-1240
Author(s):  
Lan Fang Zhang ◽  
Rui Yan Wang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Alkali Activated Slag ◽  
Percent Increase ◽  
Compressive Strength Of Concrete ◽  
Activated Slag ◽  
Lithium Slag ◽  
Alkali Activated

The aim of this paper is to study the influence of lithium-slag and fly ash on the workability , setting time and compressive strength of alkali-activated slag concrete. The results indicate that lithium-slag and fly-ash can ameliorate the workability, setting time and improve the compressive strength of alkali-activated slag concrete，and when 40% or 60% slag was replaced by lithium-slag or fly-ash, above 10 percent increase in 28-day compressive strength of concrete were obtained.

scholarly journals Protective Geopolymer Coatings Containing Multi-Componential Precursors: Preparation and Basic Properties Characterization

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Adhesive Strength ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Rapid Test ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.

scholarly journals Utilization of tailings in cement and concrete: A review

2019 ◽  
Vol 26 (1) ◽  
pp. 449-464 ◽  
Author(s):  
Mifeng Gou ◽  
Longfei Zhou ◽  
Nathalene Wei Ying Then
Keyword(s):  
Compressive Strength ◽  
Cementitious Materials ◽  
Solid Wastes ◽  
Supplementary Cementitious Materials ◽  
Cement Clinker ◽  
Fine Aggregate ◽  
Granulated Blast Furnace Slag ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Cement And Concrete

AbstractOne of the advantages of cement and the cement concrete industry in sustainability is the ability to utilize large amounts of industrial solid wastes such as fly ash and ground granulated blast furnace slag. Tailings are solid wastes of the ore beneficiation process in the extractive industry and are available in huge amounts in some countries. This paper reviews the potential utilization of tailings as a replacement for fine aggregates, as supplementary cementitious materials (SCMs) in mortar or concrete, and in the production of cement clinker. It was shown in previous research that while tailings had been used as a replacement for both fine aggregate and cement, the workability of mortar or concrete reduced. Also, at a constant water to cement ratio, the compressive strength of concrete increased with the tailings as fine aggregate. However, the compressive strength of concrete decreased as the replacement content of the tailings as SCMs increased, even whentailings were ground into smaller particles. Not much research has been dedicated to the durability of concrete with tailings, but it is beneficial for heavy metals in tailings to stabilize/solidify in concrete. The clinker can be produced by using the tailings, even if the tailings have a low SiO2 content. As a result, the utilization of tailings in cement and concrete will be good for the environment both in the solid waste processing and virgin materials using in the construction industry.

scholarly journals Study of Hydration and Microstructure of Mortar Containing Coral Sand Powder Blended with SCMs

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4248
Author(s):  
Xingxing Li ◽  
Ying Ma ◽  
Xiaodong Shen ◽  
Ya Zhong ◽  
Yuwei Li
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Silica Fume ◽  
Dilution Effect ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Limestone Powder ◽  
Chemical Effect ◽  
Granulated Blast Furnace Slag ◽  
Coral Sand

The utilization of coral waste is an economical way of using concrete in coastal and offshore constructions. Coral waste with more than 96% CaCO3 can be ground to fines and combined with supplementary cementitious materials (SCMs) such as fly ash, silica fume, granulated blast furnace slag in replacing Portland cement to promote the properties of cement concrete. The effects of coral sand powder (CSP) compared to limestone powder (LSP) blended with SCMs on hydration and microstructure of mortar were investigated. The result shows CSP has higher activity than LSP when participating in the chemical reaction. The chemical effect among CSP, SCMs, and ordinary Portland cement (OPC) results in the appearance of the third hydration peak, facilitating the production of carboaluminate. CSP-SCMs mortar has smaller interconnected pores on account of the porous character of CSP as well as the filler and chemical effect. The dilution effect of CSP leads to the reduction of compressive strength of OPC-CSP and OPC-CSP-SCMs mortars. The synergic effects of CSP with slag and silica fume facilitate the development of compressive strength and lead to a compacted isolation and transfer zone (ITZ) in mortar.

Suitability of Cordia millenii Ash Blended Cement in Concrete Production

2016 ◽  
Vol 22 ◽  
pp. 59-67 ◽  
Author(s):  
Olusola Emmanuel Babalola ◽  
Paul O. Awoyera
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Blended Cement ◽  
Cementitious Materials ◽  
Strength Properties ◽  
Supplementary Cementitious Materials ◽  
Sieve Analysis ◽  
Concrete Production ◽  
Alternative Materials ◽  
Concrete Control

Supplementary cementitious materials are most needed to enhance a sustainable development in poor communities. It is pertinent to investigate the suitability of such alternative materials for construction. The present study evaluates the strength characteristics of concrete made with varied proportion of Cordia millenii ash blended with Portland cement. Chemical composition of Cordia millenii and the setting time when blended with cement was determined. Other laboratory tests performed on Cordia millenii blended cement include: sieve analysis and specific gravity. Five replacement percentages of Cordia millenii (5%, 10%, 15%, and 20%) were blended with cement in concrete. Control specimens were also produced with only cement. Tests to determine the workability, air entrained, bulk density and compressive strength properties of the concrete were also conducted. Results obtained revealed that optimum Cordia millenii mix is 10%, which yielded the highest density and compressive strength in the concrete.

Alkali Activation of Granulated Blast Furnace Slag

2010 ◽  
Vol 158 ◽  
pp. 1-11 ◽  
Author(s):  
Zi Qiao Jin ◽  
Xian Jun Lu ◽  
Shu Gang Hu
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Portland Cement ◽  
Blast Furnace Slag ◽  
Ordinary Portland Cement ◽  
Hydration Product ◽  
Early Age ◽  
Hydration Products ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

In order to stimulate the potential cementitious property of granulated blast furnace slag (GBFS), the ground GBFS sample (Wei Fang Iron and Steel Corporation, China) was activated by lime and gypsum under different dosages. The results showed that lime is an effective activator for the slag, and the optimum dosage of lime is about 10% (w/w) of the slag. At the optimum dosage of lime, the 28 days compressive strength of the lime-slag paste is higher than that of 32.5 ordinary Portland cement (OPC). But, the early age strength (3 and 7 days compressive strength) of the lime-slag paste is lower than that of the OPC. Addition of gypsum can effectively improve the early age strength of the lime-slag paste. At the ratio of gypsum:lime:slag of 8.2:9.2:82.6 (w/w), both the early and long-term compressive strengths of the gypsum-lime-slag paste are higher than that of the OPC. According to XRD, TG-DTA and SEM detections of the hydration products of the lime-slag paste, the gypsum-lime-slag paste and the OPC paste, it reveals that the hydration process of the GBFS-based cementitious material is different from the ordinary Portland cement and the presence of ettringite (AFt) contributes to the early age strength of the pastes. The major hydration product of the OPC paste (<7 days) were measured as ettringite (AFt), but the AFt phase was not detected in the hydration product of the lime-slag paste and the major hydration product of the lime-slag paste was determined as amorphous CSH gel. However, AFt was detected in the hydration products of the gypsum-lime-slag paste in the early stages of hydration, and the formation of AFt is favorable for the early strength improvement of the material.

Modified Plasters for Restoration and Finishing Works

2014 ◽  
Vol 923 ◽  
pp. 42-47 ◽  
Author(s):  
Myroslav Sanytsky ◽  
Tetiana Kropyvnytska ◽  
Roman Kotiv
Keyword(s):  
Compressive Strength ◽  
Chemical Composition ◽  
Cementitious Materials ◽  
Quality Parameters ◽  
Supplementary Cementitious Materials ◽  
Cement Matrix ◽  
Hydration Products ◽  
High Quality ◽  
Physico Chemical ◽  
White Portland Cement

The paper is devoted to the research and development of modified plasters for restoration and finishing works based on decorative multicomponent cements containing white Portland cement and supplementary cementitious materials (silica fume, metakaolin and fine ground limestone). This cements are similar to Roman cement by their chemical composition. The use of optimal granulometry of decorative multicomponent cements provide directed formation of microstructure of the cement matrix with the formation of stable hydration products. Compositions of modified plasters by the criterions of workability and compressive strength were designed. Physico-chemical modification of plaster by complex air-entraining admixture allows to obtain high-quality modified plasters with improved quality parameters.

Sign in / Sign up

Export Citation Format

Share Document