scholarly journals Color Shift, Color Stability, and Post-Polishing Surface Roughness of Esthetic Resin Composites

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1376
Author(s):  
Yara Khalid Alkhadim ◽  
Malak Jameel Hulbah ◽  
Hani Mohammad Nassar
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Distilled Water ◽  
Significance Level ◽  
Color Changes ◽  
Significant Difference ◽  
Color Shift ◽  
Optical Profilometer ◽  
System Data ◽  
Multiple Comparison Methods

The aim of this study was to compare color shift, color stability, and post-polishing surface roughness of esthetic restorative materials. Twenty-five disc-shaped specimens (10 mm in diameter and 2 mm in thickness) from five esthetic resin materials (Z250XT, IPS Empress-Direct, G-ænial, Vit-l-escence, and Ceram.X) were fabricated. Color shift before and immediately after light-curing (∆E0) then color stability after immersion in tea, coffee, berry juice, and distilled water were measured using a spectrophotometer. Color changes were measured after 2 (ΔE2), 4 (ΔE4), 6 (ΔE6), and 8 weeks (ΔE8). Surface roughness values (Rq) were determined using an optical profilometer after polishing using a rotary polishing system. Data were analyzed using ANOVA and multiple comparison methods at 0.05 significance level. There were no significant differences between the tested materials regarding color shift except between Vit-l-escence and Ceram.X (p = 0.033). There was no significant difference between coffee and tea solutions (p = 1.0) and between berry juice and distilled water (p = 0.15). There was no difference between the tested materials regarding Rq (p = 0.057). Ceram.X was associated with the lowest ΔE8 values overall. Tested materials were comparable regarding color shift and post-polishing surface roughness. Susceptibility to staining was dependent on the material.

scholarly journals Effects of Mouth Rinses on Color Stability of Resin Composites

2008 ◽  
Vol 02 (04) ◽  
pp. 247-253 ◽  
Author(s):  
Cigdem Celik ◽  
Bulem Yuzugullu ◽  
Selim Erkut ◽  
Kıvanc Yamanel
Keyword(s):  
Color Change ◽  
Calculated Data ◽  
Color Stability ◽  
Color Difference ◽  
Distilled Water ◽  
Significance Level ◽  
Color Changes ◽  
Mouth Rinses ◽  
Significant Difference ◽  
Restorative Materials

ABSTRACTObjectives: The aim of this study was to evaluate the effects of 3 commercially available mouth rinses on the color stability of 4 different resin-based composite restorative materials.Methods: Forty disc-shaped specimens (10x2 mm) were prepared from each of the following materials: A nanofill composite Filtek Supreme XT (3M/Espe, St. Paul, MN, USA); a packable lowshrinkage composite, AeliteLS Packable (BISCO, Inc, Shaumburg, IL, USA); nanoceramic compositeresin Ceram-X (Dentsply, Konstanz, Germany); a microhybrid composite, and Aelite All-Purpose Body (BISCO). The specimens were then incubated in distilled water at 37°C for 24 hours. The baseline color values (L*, a*, b*) of each specimen were measured with a colorimeter according to the CIELAB color scale. After baseline color measurements, 10 randomly selected specimens from each group were immersed in 1 of the 3 mouth rinses and distilled water as control. The specimens were stored in 20 mL of each mouth rinse (Oral B Alcohol-free, Listerine Tooth Defense Anti-cavity Fluoride Rinse and Klorhex) for 12 hours. After immersion, the color values of all specimens were remeasured, and the color change value ΔE*ab was calculated. Data were analyzed using a 2-way analysis of variance at a significance level of .05.Results: All specimens displayed color changes after immersion, and there was a statistically significant difference among restorative materials and mouth rinses (P<.05); however, the change was not visually perceptible (ΔE*ab<3.3). The interaction between the effect of mouth rinses and type of restorative materials was not statistically significant (P>.05).Conclusions: It may be concluded that although visually nonperceptible, all resin restorative materials tested showed a color difference after immersion in different mouth rinses. (Eur J Dent 2008;2:247-253)

scholarly journals Evaluation of the color stability and surface roughness of dual-cure, bulk-fill composites

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 266-273
Author(s):  
Zehra Şivgan Güner ◽  
Behiye Bolgül ◽  
Tacettin İnandı
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Pediatric Dentistry ◽  
Ease Of Use ◽  
Composite Resins ◽  
Distilled Water ◽  
Significant Difference ◽  
Cherry Juice ◽  
Experimental Group ◽  
Composite Samples

Aim: In recent years, tooth-colored, dual-cure, bulk-fill composite resins, which have attracted attention for their ease of use, constitute one of the latest developments in pediatric dentistry applications. This study aimed to evaluate the color stability and surface roughness properties of three different dual-cure, bulk-fill materials and one light-cure, bulk-fill composite material used in pediatric dentistry. Methodology: In this study, three different dual-cure, bulk-fill composites (Fill-Up, HyperFIL, Cention-N) and one light-polymerized bulk-fill composite (Reveal HD) were used. A total of 70 samples were obtained for surface roughness testing. The surface roughness testing was performed with a Hysitron TI 950 Triboindenter device. A total of 105 samples were obtained for the evaluation of color stability. Cherry juice, iced tea, and distilled water were used as solutions. Initial and final color measurements were made using a spectrophotometer. The color differences between measurements were recorded according to the CIEDE 2000 system. Results: The least surface roughness among the composite groups was observed in the light polymerized Cention-N composite samples in the experimental group. In the Fill-Up and Cention-N composite groups in the experimental group, the surface roughness of the samples left to self-polymerization and the samples polymerized with light showed a statistically significant difference (p < 0.05). Among the composite groups, the highest amount of coloring was observed in the Fill-Up composite samples, which were left to self-polymerization and kept in cherry juice in the experimental group. The least coloration among the composite groups was observed in the Cention-N composite samples polymerized with light and kept in distilled water. Conclusion: Based on this information, a decrease in surface roughness and an increase in color stability can be expected due to self-polymerization and the light polymerization of dual-cured, bulk-fill composites.   How to cite this article: Şivgan Güner Z, Bolgül B, İnandı T. Evaluation of the color stability and surface roughness of dual-cure, bulk-fill composites. Int Dent Res 2021;11(Suppl.1):266-273. https://doi.org/10.5577/intdentres.2021.vol11.suppl.39   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

scholarly journals Influence of Photoinitiator on Accelerated Artificial Aging and Bond Strength of Experimental Resin Cements

2018 ◽  
Vol 29 (1) ◽  
pp. 82-87
Author(s):  
Helouise Righi ◽  
Ana Rosa Costa ◽  
Dayane Carvalho Ramos Salles de Oliveira ◽  
Gabriel Flores Abuna ◽  
Mario Alexandre Coelho Sinhoreti ◽  
...  
Keyword(s):  
Bond Strength ◽  
Color Stability ◽  
Test Results ◽  
Color Analysis ◽  
Color Test ◽  
Resin Cements ◽  
Significance Level ◽  
Significant Difference ◽  
System Data

Abstract The goal of this study was to evaluate in vitro the effect of the photoinitiator phenylpropanedione (PPD), alone or combined with camphorquinone (CQ), on color stability of photoactivated resin cements and their bond strength to ceramics using a micro-shear test. Four resin cements were used: a commercial brand cement (RelyX Veneer®) and 3 experimental cements with different types and concentration of photoinitiators. For color analysis, ceramic discs were cemented on bovine dentin specimens to simulate indirect restorations (n=8) and were exposed to UV for 120 h and tested for color alteration using a reflectance spectrophotometer and the CIEL*a*b* system. Data were analyzed by Anova and Tukey’s test at 5% significance level. The color test results did not present statistically significant difference for the ∆E for all the studied cements, neither for ∆L, ∆a and ∆b. For the bond strength, all the studied cements showed statistically significant differences to each other, with the highest result for the RelyX Veneer® (29.07 MPa) cement, followed by the cement with CQ (21.74 MPa) and CQ+PPD (19.09 MPa) cement; the lowest result was obtained by the cement using only PPD as a photoinitiator (13.99 MPa). So, based on the studied parameters, PPD was not advantageous as photoinitiator of resin cements, because it showed a low value of bond strength to the ceramics and no superior color stability.

scholarly journals Varying the Polishing Protocol Influences the Color Stability and Surface Roughness of Bulk-Fill Resin-Based Composites

2020 ◽  
Vol 12 (1) ◽  
pp. 1
Author(s):  
Filipa Freitas ◽  
Teresa Pinheiro de Melo ◽  
António HS Delgado ◽  
Paulo Monteiro ◽  
João Rua ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Color Change ◽  
Resin Composite ◽  
Color Stability ◽  
Control Surface ◽  
Significance Level ◽  
Color Changes ◽  
Atomic Force ◽  
Polishing Procedures

Surface properties of composites such as roughness and color impact periodontal health and aesthetic outcomes. Novel bulk-fill composites with improved functionality are being introduced and, in light of the existing variety of finishing/polishing procedures, research of their surface properties is warranted. Sixty discs were prepared from bulk-fill composites (Filtek™ Bulk Fill Posterior Restorative and Fill-Up™) and incremental-fill Filtek™ Z250. They were further divided according to different polishing procedures (n = 5): three multi-step polishing procedures or finishing with a bur (control). Surface roughness (Ra) was measured using an atomic force microscope (The AFM Workshop TT-AFM). A spectrophotometer (Spectroshade Micro Optic) was used to determine color stability, after exposure to a coffee solution. Data were analyzed using two-way MANOVA (significance level of 5%). Resin composite type, polishing procedure, and their interaction had a statistically significant effect on surface roughness (p < 0.001) and color change (p < 0.001). Fill-Up™ exhibited the highest surface roughness and greatest color change. Differences in color change were statistically significant (p < 0.001). Filtek™ Bulk Fill registered the lowest surface roughness and color change, after the three-step polishing procedure. Both parameters were significantly correlated (ρ = 0.754, p < 0.001) and found to be material dependent and polishing-procedure dependent. Higher surface roughness relates to greater color changes.

scholarly journals Effect of 2 Bleaching Agents with a Content of High Concentrated Hydrogen Peroxide on Stained 2 CAD/CAM Blocks and a Nanohybrid Composite Resin: An AFM Evaluation

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
İzgen Karakaya ◽  
Esra Cengiz
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Control Group ◽  
Whiteness Index ◽  
Color Changes ◽  
Significant Difference ◽  
Cad Cam ◽  
Cielab System ◽  
And Control ◽  
Pure White

The aim of this study was to evaluate color stability of 3 restorative materials, discoloration ability of different solutions, efficacy of 2 office bleaching agents, and surface roughness and topography. Sixty specimens for Clearfil Majesty Esthetic (CME), Lava Ultimate (LU), and Vita Enamic (VE) were prepared. They were immersed into 3 staining solutions for 2 weeks and then they were bleached. According to the measuredL⁎,a⁎, andb⁎parameters described by CIELAB system, color changes (ΔE00), translucency parameters (TP), whiteness index values (W⁎), and changes in closeness to pure white (ΔW⁎) were calculated. Then 3 specimens from each group were scanned with an atomic force microscope for surface analysis. After staining, CME groups and control groups of LU and VE showed clinically acceptable color changes (ΔE00<1,8). After bleaching, while a reverse effect on color was observed, VE showed the furthest color values to pure white. There was no statistically significant difference between whiteness index values of LU and CME. LU was the most translucent material during the study and TP values of materials showed minimal differences. Most of the VE groups and a control group of LU showed surface roughness (Ra) values higher than critical value for biofilm accumulation (0,2 μm).

scholarly journals Effect of an Optical Whitening Toothpaste on Color Stability of Tooth-Colored Restorative Materials

2020 ◽  
Vol 14 (01) ◽  
pp. 085-091
Author(s):  
Sedighe Sadat Hashemikamangar ◽  
Farnoosh Hoseinpour ◽  
Nazanin Kiomarsi ◽  
Mehrzad Gholampour Dehaki ◽  
Mohammad Javad Kharazifard
Keyword(s):  
Statistical Analysis ◽  
Color Change ◽  
Color Stability ◽  
Composite Resins ◽  
Time Points ◽  
Color Changes ◽  
Honestly Significant Difference ◽  
Significant Difference ◽  
Resin Modified Glass Ionomer ◽  
Composite Samples

Abstract Objectives This study aimed to assess the effect of an optical whitening toothpaste on color stability of microhybrid, nanofilled, and microfilled composite resins and resin-modified glass ionomer (RMGI) cement in comparison of two other toothpastes. Materials and Methods In this experimental study, disc-shaped composite samples were fabricated. The samples were then polished using silicon carbide papers. Twenty-seven samples of each material were fabricated and subjected to colorimetry using a spectrophotometer. Each group of material was then divided into three subgroups for the application of conventional whitening and whitening containing blue covarine toothpastes. One operator brushed the samples with an electric soft toothbrush with circular motion twice a day, each time for 30 seconds. Colorimetry was performed at 0, 1, 7, 30, and 90 days. Statistical Analysis Two-way analysis of variance (ANOVA), one-way ANOVA, and Tukey’s honestly significant difference (HSD) test were used for statistical analysis. Results The interaction effect of type of restorative material and time on ∆E was not significant at baseline or 1 day (p > 0.05). The effect of type of toothpaste on ∆E was not significant at baseline or 1 day (p = 0.78) but the effect of type of material was significant (p < 0.05). The toothpastes had significantly different effects on ∆E of Z250 at all time points (p < 0.05) except for ∆E0–30 (p = 0.106). The toothpastes had significantly different effects on ∆E of Z350 and Gradia at all time points (p < 0.05). The same was true for RMGI except for ∆E0–7 (p = 0.43) and ∆E0–90 (p = 0.52). The majority of color changes caused by toothpastes were not clinically perceivable (∆E < 3.3), except for ∆E0–90 by the whitening toothpaste (∆E = 9), ∆E0–90 by the conventional toothpaste for Z350 (∆E = 3.9), and ∆E0–1 by the whitening toothpaste for RMGI (∆E = 3.7). Conclusion The color change of all composite samples was not clinically perceivable (<3.3) at all time points, which shows that the tested toothpastes do not cause a significant change in color of composite materials.

scholarly journals Evaluation of color change in acrylic and bisacrylic resin resins in different solutions

2018 ◽  
Vol 5 (4) ◽  
pp. 76
Author(s):  
Mone Laiz Bortoli ◽  
Cristina Von Appen ◽  
Camila Longoni ◽  
Carmen Beatriz Borges Fortes ◽  
Jefferson Tomio Sanada
Keyword(s):  
Color Change ◽  
Color Stability ◽  
Acrylic Resin ◽  
Color Variation ◽  
Color Reading ◽  
Control Group ◽  
Color Changes ◽  
Significant Difference ◽  
Prosthesis Material ◽  
Chlorhexidine Solution

Aim: This work aimed to evaluate the color stability of an acrylic resin chemically activated (ARCA) using different handling techniques, and a bisacrylic resin when exposed to different pigmentation solutions.Material and Methods: Silicon matrixes were confectioned (10x10x3mm) to be used as specimens. The groups were designed as follows: Group Pot, Group Brush, Group Manufacturer and Group Bisacrylic (n=18). Each group was exposed to three different pigmentation solutions: distilled water, coke and chlorhexidine digluconate 0.12%. Three readings were performed for each specimen using a spectrophotometer, and the evaluations were carried out in three different time. After the color reading, three averages and the standard deviation of variation were performed after 24 hours (T1), 7 days (T2) and 14 days (T3). Data were submitted to the ANOVA and 2 criteria and Tukey (P<0.05) in the statistical software SSPS 18 for Macintosh (SPSS Inc., Chicago, USA).Results: When compared the solutions in each group of material, there was no statistically significant difference, except for T3, where the group Dencor Brush and Bisacrylic demonstrated higher color variation in all the solutions, even in the control group, and the values in Chlorhexidine higher than the other, showing greater instability after 14 days.Conclusions: With the results, bisacrylic resin used as provisory prosthesis material presents greater color instability than the ARCA, when submitted to different solutions. Bisacrylic resin and Dencor Brush present significantly visible color changes in chlorhexidine solution after 14 days. All the materials in coke solution present homogeneity in the color change after 7 days exposition to the solution, with no visible color change.

scholarly journals The effect of optical brightening toothpaste on the color stability of esthetic restorative materials

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 81-85
Author(s):  
Firdevs Kahvecioğlu ◽  
Elçim Çoban ◽  
Hayriye Esra Ülker
Keyword(s):  
Color Change ◽  
Calculated Data ◽  
Color Stability ◽  
Color Changes ◽  
Significant Difference ◽  
Restorative Materials ◽  
Cherry Juice ◽  
Native Speakers Of English ◽  
Materials Used ◽  
Post Hoc

Aim: The aim of this study is to evaluate the effects of whitening toothpaste applications on the color stability of different tooth-colored restorative materials (Fuji IX, GC Fuji II LC, Equia Forte, and Kerr Point 4)  Methodology: Standardized fourty disc-shaped specimens were prepared from esthetic restorative materials and polished. The baseline color values of each specimen were then measured using a spectrophotometer, according to the Commission Internationale de l'Eclairage L*, a*, and b* (CIELAB) color scale. Ten specimens from each group were then immersed in two different beverages (cherry juice and coke) for seven days. After immersion, the color value of each specimen was re-measured. Each sample was brushed with whitening toothpaste for 30 seconds using an electric toothbrush. The samples were kept in distilled water at room temperature and brushing continued twice a day for seven days. The color change value, Delta E (ΔE), was calculated. Data were analyzed by two-way ANOVA and post hoc Tukey's test. Results: When the results were evaluated, after the colored samples had been brushed with whitening toothpaste, a difference was found between the Delta E values according to the materials used (p<0.001), but no difference was found in relation to the beverages (p>0.001). When the values of the color changes were evaluated after the first brushing with whitening toothpaste and before the specimens were colored with drinks, a difference was observed in the Fuji II cola, Fuji II cherry, and Equia Forte cola groups (p<0.05). When the values of the color changes were evaluated for specimens in which brushing had been done twice a day for seven days with whitening toothpaste and before they were colored with drinks, a significant difference was observed in the Fuji II cherry and Equia Forte cola groups (p<0.05). Conclusion: Using Signal White Now whitening toothpaste for 2 min 2 times a day for seven days caused significant changes in the color of the restorative materials. The color change is dependent upon the type of restorative material that is used.   How to cite this article: Kahvecioğlu F, Çoban E, Ülker HE. The effect of optical brightening toothpaste on the color stability of esthetic restorative materials. Int Dent Res 2021;11(Suppl.1):80-4. https://doi.org/10.5577/intdentres.2021.vol11.suppl1.13   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

scholarly journals Bleaching Agent Action on Color Stability, Surface Roughness and Microhardness of Composites Submitted to Accelerated Artificial Aging

2011 ◽  
Vol 05 (02) ◽  
pp. 143-149 ◽  
Author(s):  
Raphael Mendes Bezerra Rattacaso ◽  
Lucas de Fonseca Roberti Garcia ◽  
Fabiano Gamero Aguilar ◽  
Simonides Consani ◽  
Fernanda de Carvalho Panzeri Pires-de-Souza
Keyword(s):  
Surface Roughness ◽  
Artificial Aging ◽  
Artificial Saliva ◽  
Color Stability ◽  
Color Reading ◽  
Bleaching Agent ◽  
Significant Difference ◽  
Knoop Microhardness ◽  
Initial Color ◽  
Daily Application

ABSTRACTObjectives: The purpose of this study was to evaluate the bleaching agent action on color stability, surface roughness and microhardness of composites (Charisma, Filtek Supreme and Heliomolar - A2) submitted to accelerated artificial aging (AAA). Methods: A Teflon matrix (12 x 2 mm) was used to fabricate 18 specimens (n=6) which, after polishing (Sof-Lex), were submitted to initial color reading (ΔE), Knoop microhardness (KHN) (50 g/15 s load) and roughness (Ra) (cut-off 0.25 mm) tests. Afterwards, the samples were submitted to AAA for 384 hours and new color, microhardness and roughness readings were performed. After this, the samples were submitted to daily application (4 weeks) of 16% Carbamide Peroxide (NiteWhite ACP) for 8 hours and kept in artificial saliva for 16 hours. New color, microhardness and roughness readings were made at the end of the cycle, and 15 days after bleaching. Results: Comparison of the ΔE means (2-way ANOVA, Bonferroni, P<.05) indicated clinically unacceptable color alteration for all composites after AAA, but without significant difference. Statistically significant increase in the KHN values after AAA was observed, but without significant alterations 15 days after bleaching. For Ra there was no statistically significant difference after AAA and 15 days after bleaching. Conclusions: The alterations promoted by the bleaching agent and AAA are material dependent. (Eur J Dent 2011;5:143-149)

scholarly journals Effect of In-Office Bleaching on Color and Surface Roughness of Composite Restoratives

2010 ◽  
Vol 04 (02) ◽  
pp. 118-127 ◽  
Author(s):  
Randa Hafez ◽  
Doa Ahmed ◽  
Mai Yousry ◽  
Wafa El-Badrawy ◽  
Omar El-Mowafy
Keyword(s):  
Surface Roughness ◽  
Surface Texture ◽  
Color Change ◽  
Distilled Water ◽  
Bleaching Agent ◽  
Color Changes ◽  
Before And After ◽  
Colorimetric Measurements ◽  
Natural Teeth ◽  
Environmental Sem

Objectives: The purpose of this study was to determine color changes and surface roughness of composites when they were subjected to in-office bleaching.Methods: 12 discs 15 mm in diameter and 2 mm thick were prepared from two shades (A2 & A4) of two composites, Durafil VS (DF) and TPH3 (TPH). Specimens were polished and stored in distilled water for 24 hours at 37°C before being subjected to bleaching, staining, and re-bleaching. Each of the groups of specimens (DF-A2, DF-A4, TPH-A2 and TPH-A4) were subdivided into three subgroups (n=4) and bleached with Beyond, LumaWhite-Plus, and Opalescence-Boost. Specimens were then stained by immersing them in a coffee solution for 48 hours at 37°C, and then they were re-bleached. Colorimetric measurements were performed at baseline, after bleaching, after staining, and after rebleaching. Surface roughness was determined with environmental SEM before and after bleaching. Data were statistically-analyzed.Results: None of the bleaching systems notably changed the color of composites (delta-E<2). Coffee staining affected DF specimens more than TPH. Stained specimens showed variable responses to whitening with no significant color change observed with TPH (delta-E<2) and significant changes observed with DF. Surface roughness significantly changed with bleaching, but the degree varied according to composite shade and bleaching agent.Conclusions: Three in-office bleaching agents had no significant color changes on two composites. DF showed more color change than TPH when immersed in coffee. Stained composites showed different degrees of whitening, with DF showing more response. Bleaching may adversely affect the surface texture of composites. Dentists should take into consideration that composite restorations may not respond to bleaching in the same way that natural teeth do. (Eur J Dent 2010;4:118-127)

Sign in / Sign up

Export Citation Format

Share Document