scholarly journals Experimental Insights into Concrete Flow-Regimes Subject to Shear-Induced Particle Migration (SIPM) during Pumping

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1233 ◽  
Author(s):  
Shirin Fataei ◽  
Egor Secrieru ◽  
Viktor Mechtcherine
Keyword(s):  
Flow Pattern ◽  
Volume Fraction ◽  
Discharge Rate ◽  
High Volume ◽  
Particle Migration ◽  
Hardened Concrete ◽  
Concrete Pipe ◽  
Lubricating Layer ◽  
Definition Of ◽  
Concrete Flow

In this paper, the authors have focused on shear-induced particle migration (SIPM), its effect on concrete flow patterns, and lubricating layer formation during pumping. For this purpose, various volume-fractions ϕ of aggregates were selected. The particle migration was analyzed by applying two methods: sampling hardened concrete exposed to pumping and performing X-ray microcomputed tomography (μCT) and image analysis to determine the thickness of the lubricating layer due to SIPM. The results indicate that the first approach is unsuitable due to the nearly equal molecular density of particles and matrix. The second approach indicated that the actual thickness of the lubricating layer depends on the discharge rate as well as on ϕ and viscosity of concrete bulk; hence, it cannot be defined as a constant parameter for all concrete mixtures. Additionally, the concrete pipe-flow pattern, i.e., plug versus shear flow, was captured and studied while considering pumping pressure and discharge rate. It was concluded that particle migration is essential in the cases of both flowable and very flowable concretes with a high volume-fraction of solids. The changes in rheological properties caused by SIPM are severe enough to influence the definition of the flow pattern as plug or shear and the discharge rate of pumped concrete as well.

Morphology, Distribution and Identification of Micro-Constituents Along Grain Boundaries in Nickel-Base Alloys

1973 ◽  
Vol 31 ◽  
pp. 176-177
Author(s):  
D. E. Fornwalt ◽  
A. R. Geary ◽  
B. H. Kear
Keyword(s):  
Electron Microscope ◽  
Grain Boundaries ◽  
Volume Fraction ◽  
Rupture Life ◽  
Stress Rupture ◽  
High Volume ◽  
Precipitate Morphology ◽  
Stress Rupture Life ◽  
Nickel Base ◽  
Scanning Electron

A systematic study has been made of the effects of various heat treatments on the microstructures of several experimental high volume fraction γ’ precipitation hardened nickel-base alloys, after doping with ∼2 w/o Hf so as to improve the stress rupture life and ductility. The most significant microstructural chan§e brought about by prolonged aging at temperatures in the range 1600°-1900°F was the decoration of grain boundaries with precipitate particles.Precipitation along the grain boundaries was first detected by optical microscopy, but it was necessary to use the scanning electron microscope to reveal the details of the precipitate morphology. Figure 1(a) shows the grain boundary precipitates in relief, after partial dissolution of the surrounding γ + γ’ matrix.

HOT CORROSION OF CERIA-YTTRIA STABILIZED ZIRCONIA PLASMA SPRAYED THERMAL BARRIER COATING BY EUTECTIC VANDIUM PENTAOXIDE-SODIUM SULFATE

2018 ◽  
Vol 18 (1) ◽  
pp. 182-192 ◽  
Author(s):  
Mohammed J Kadhim ◽  
Mohammed H Hafiz ◽  
Maryam A Ali Bash
Keyword(s):  
Thermal Barrier Coating ◽  
Hot Corrosion ◽  
Monoclinic Phase ◽  
Volume Fraction ◽  
High Volume ◽  
Thermal Barrier ◽  
Air Plasma ◽  
Plan View ◽  
Barrier Coating ◽  
Plasma Sprayed

The high temperature corrosion behavior of thermal barrier coating (TBC) systemconsisting of IN-738 LC superalloy substrate, air plasma sprayed Ni24.5Cr6Al0.4Y (wt%)bond coat and air plasma sprayed ZrO2-20 wt% ceria-3.6 wt% yttria (CYSZ) ceramic coatwere characterized. The upper surfaces of CYSZ covered with 30 mg/cm2 , mixed 45 wt%Na2SO4-55 wt% V2O5 salt were exposed at different temperatures from 800 to 1000 oC andinteraction times from 1 up to 8 h. The upper surface plan view of the coatings wereidentified for topography, roughness, chemical composition, phases and reaction productsusing scanning electron microscopy, energy dispersive spectroscopy, talysurf, and X-raydiffraction. XRD analyses of the plasma sprayed coatings after hot corrosion confirmed thephase transformation of nontransformable tetragonal (t') into monoclinic phase, presence ofYVO4 and CeVO4 products. Analysis of the hot corrosion CYSZ coating confirmed theformation of high volume fraction of YVO4, with low volume fractions of CeOV4 and CeO2.The formation of these compounds were combined with formation of monoclinic phase (m)from transformation of nontransformable tetragonal phase (t').

scholarly journals Face Grinding Surface Quality of High Volume Fraction SiCp/Al Composite Materials

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Xu Zhao ◽  
Yadong Gong ◽  
Guiqiang Liang ◽  
Ming Cai ◽  
Bing Han
Keyword(s):  
Friction Coefficient ◽  
Surface Morphology ◽  
Surface Quality ◽  
Volume Fraction ◽  
High Volume ◽  
Spindle Speed ◽  
High Volume Fraction ◽  
Machining Parameters ◽  
Al Composite

AbstractThe existing research on SiCp/Al composite machining mainly focuses on the machining parameters or surface morphology. However, the surface quality of SiCp/Al composites with a high volume fraction has not been extensively studied. In this study, 32 SiCp/Al specimens with a high volume fraction were prepared and their machining parameters measured. The surface quality of the specimens was then tested and the effect of the grinding parameters on the surface quality was analyzed. The grinding quality of the composite specimens was comprehensively analyzed taking the grinding force, friction coefficient, and roughness parameters as the evaluation standards. The best grinding parameters were obtained by analyzing the surface morphology. The results show that, a higher spindle speed should be chosen to obtain a better surface quality. The final surface quality is related to the friction coefficient, surface roughness, and fragmentation degree as well as the quantity and distribution of the defects. Lower feeding amount, lower grinding depth and appropriately higher spindle speed should be chosen to obtain better surface quality. Lower feeding amount, higher grinding depth and spindle speed should be chosen to balance grind efficiently and surface quality. This study proposes a systematic evaluation method, which can be used to guide the machining of SiCp/Al composites with a high volume fraction.

scholarly journals Study on the High-Speed Milling Performance of High-Volume Fraction SiCp/Al Composites

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4143
Author(s):  
Youzheng Cui ◽  
Shenrou Gao ◽  
Fengjuan Wang ◽  
Qingming Hu ◽  
Cheng Xu ◽  
...  
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Volume Fraction ◽  
Simulation Analysis ◽  
Cutting Temperature ◽  
High Volume ◽  
Cutting Parameters ◽  
High Volume Fraction ◽  
High Wear Resistance ◽  
Element Analysis

Compared with other materials, high-volume fraction aluminum-based silicon carbide composites (hereinafter referred to as SiCp/Al) have many advantages, including high strength, small change in the expansion coefficient due to temperature, high wear resistance, high corrosion resistance, high fatigue resistance, low density, good dimensional stability, and thermal conductivity. SiCp/Al composites have been widely used in aerospace, ordnance, transportation service, precision instruments, and in many other fields. In this study, the ABAQUS/explicit large-scale finite element analysis platform was used to simulate the milling process of SiCp/Al composites. By changing the parameters of the tool angle, milling depth, and milling speed, the influence of these parameters on the cutting force, cutting temperature, cutting stress, and cutting chips was studied. Optimization of the parameters was based on the above change rules to obtain the best processing combination of parameters. Then, the causes of surface machining defects, such as deep pits, shallow pits, and bulges, were simulated and discussed. Finally, the best cutting parameters obtained through simulation analysis was the tool rake angle γ0 = 5°, tool clearance angle α0 = 5°, corner radius r = 0.4 mm, milling depth ap = 50 mm, and milling speed vc= 300 m/min. The optimal combination of milling parameters provides a theoretical basis for subsequent cutting.

scholarly journals High concentration Brownian coagulation in jet flow using two enhancement formulations

2012 ◽  
Vol 16 (5) ◽  
pp. 1519-1523
Author(s):  
Pei-Feng Lin ◽  
Di-Chong Wu ◽  
Ze-Fei Zhu
Keyword(s):  
Volume Fraction ◽  
Taylor Series Expansion ◽  
Expansion Method ◽  
High Volume ◽  
Jet Flow ◽  
High Concentration ◽  
Brownian Coagulation ◽  
Planar Jet ◽  
Ultra Fine Particle ◽  
The One

Ultra-fine particle coagulation by Brownian motion at high concentration in planar jet flow is simulated. A Taylor-Series Expansion Method of Moments is employed to solve the particle general dynamic equation. The volume fraction gets high value, very closes to that at the nozzle exit. As the vortex pairing develops, the high volume fraction region rolls out and mixes with the low value region. The enhancement factor given by Trzeciak et al. will be less than one at some specific outer positions, which seems to be less accurate than the one given by Heine et al.

Formabilities of C-Si-Al-Mn Transformation-Induced Plasticity-Aided Martensitic Sheet Steel

2016 ◽  
Vol 838-839 ◽  
pp. 546-551
Author(s):  
Junya Kobayashi ◽  
Yumenori Nakashima ◽  
Koh Ichi Sugimoto ◽  
Goroh Itoh
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Lath Martensite ◽  
Sheet Steel ◽  
Void Formation ◽  
High Volume ◽  
Stress Concentrations ◽  
Transformation Induced Plasticity ◽  
Al Content

The substitution of Si with Al in 0.2%C-1.5%Si-1.25%Mn-0.2%Cr ultrahigh strength transformation-induced plasticity (TRIP)-aided martensitic (TM) sheet steel improves galvanization. The effect of Al content on the microstructure and formabilities of the TM steel was therefore investigated. Replacement of Si with Al maintained the high volume fraction of the retained austenite and the high stretch-formability and stretch-flangeability, whereas it decreased the tensile strength. Complex addition of Si and Al yielded the best formabilities with 1.5 GPa tensile strength grade. The superior formabilities of Si-Al bearing TM steel were attributed to the strain-induced transformation of the metastable retained austenite and the relatively soft lath-martensite structure matrix. The former leads to plastic relaxation of the localized stress concentrations, thus suppressing void formation.

Insight into the Formation of Ultrafine Nanostructures in Bulk Amorphous Zr54.5 Ti7.5Al10Cu20Ni8

2001 ◽  
Vol 703 ◽  
Author(s):  
André Heinemann ◽  
Helmut Hermann ◽  
Albrecht Wiedenmann ◽  
Norbert Mattern ◽  
Uta Kühn ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Volume Fraction ◽  
High Volume ◽  
High Resolution Electron Microscopy ◽  
Scattering Data ◽  
Scanning Calorimetry ◽  
Enhanced Diffusion ◽  
Resolution Electron ◽  
The Mean ◽  
Interparticle Interference

ABSTRACTBulk amorphous Zr54.5 Ti7.5Al10Cu20Ni8 is investigated by means of smal-angle neutron scattering (SANS), differential-scanning calorimetry (DSC), high-resolution electron microscopy (HREM) and other methods. The formation of ultrafine nanostructures in the glassy phase is observed and explained by a new model. Structura fluctuations of randomly distributed partialy ordered domains grow during annealing just below the glass transition temperature by local re-ordering. During anneaing the DSC gives evidence for a increasing volume fraction of the localy ordered domains. At high volume fractions of impinging domains a percolation threshold on the interconnected domain boundaries occurs and enhanced diffusion becomes possible. At that stage SANS measurements lead to satistically significant scattering data. The SANS signals are anayzed in terms of a model taking into account spherica particles surrounded by diffusion zones and interparticle interference effects. The mean radius of the nanocrystaline particles is determined to 1 nm and the mean thickness of the depletion zone is 2 nm. The upper limit for the volume fraction after annealing at 653 K for 4hours is about 20 %. Electron microscopy confirms the size and shows that the particle are crystaline.

Sign in / Sign up

Export Citation Format

Share Document