scholarly journals Bio-Based Polymer Electrolytes for Electrochemical Devices: Insight into the Ionic Conductivity Performance

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 838 ◽  
Author(s):  
Marwah Rayung ◽  
Min Min Aung ◽  
Shah Christirani Azhar ◽  
Luqman Chuah Abdullah ◽  
Mohd Sukor Su’ait ◽  
...  
Keyword(s):  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Future Prospects ◽  
Electrolyte System ◽  
The Past ◽  
Device Applications ◽  
Electrochemical Devices ◽  
Insight Into ◽  
General Method

With the continuing efforts to explore alternatives to petrochemical-based polymers and the escalating demand to minimize environmental impact, bio-based polymers have gained a massive amount of attention over the last few decades. The potential uses of these bio-based polymers are varied, from household goods to high end and advanced applications. To some extent, they can solve the depletion and sustainability issues of conventional polymers. As such, this article reviews the trends and developments of bio-based polymers for the preparation of polymer electrolytes that are intended for use in electrochemical device applications. A range of bio-based polymers are presented by focusing on the source, the general method of preparation, and the properties of the polymer electrolyte system, specifically with reference to the ionic conductivity. Some major applications of bio-based polymer electrolytes are discussed. This review examines the past studies and future prospects of these materials in the polymer electrolyte field.

Structural and Ionic Conductivity Studies of CMC Based Polymerelectrolyte Doped with NH4Cl

2015 ◽  
Vol 1107 ◽  
pp. 247-252 ◽  
Author(s):  
Nur Hidayah Ahmad ◽  
M.I.N. Isa
Keyword(s):  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Ammonium Chloride ◽  
Polymer Electrolytes ◽  
Chloride Concentration ◽  
Xrd Analysis ◽  
Electrolyte System ◽  
Conductivity Enhancement ◽  
Ftir Studies ◽  
Amorphous Nature

The present study aims to investigate the structural and ionic conductivity of carboxymethyl cellulose - ammonium chloride as proton conducting polymer electrolytes. The complexion of polymer electrolyte films has been confirmed via FTIR studies. The conductivity enhancement with the addition of ammonium chloride concentration was proved due to the increase in amorphous nature of the films as evidenced by XRD analysis. Impedance studies indicate that the highest ionic conductivity of 1.43 x 10-3 Scm-1 was observed with the addition of 16 wt.% ammonium chloride in polymer electrolyte system obtained at ambient temperature.

Highly efficient solid polymer electrolytes using ion containing polymer microgels

2015 ◽  
Vol 6 (7) ◽  
pp. 1052-1055 ◽  
Author(s):  
Suting Yan ◽  
Jianda Xie ◽  
Qingshi Wu ◽  
Shiming Zhou ◽  
Anqi Qu ◽  
...  
Keyword(s):  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Lithium Batteries ◽  
Polymer Electrolytes ◽  
Solid Polymer Electrolyte ◽  
Solid Polymer Electrolytes ◽  
High Ionic Conductivity ◽  
Solid Polymer ◽  
Highly Efficient ◽  
Potential Use

A solid polymer electrolyte fabricated using ion containing microgels manifests high ionic conductivity for potential use in lithium batteries.

scholarly journals Characteristics of Dye-Sensitized Solar Cell Assembled from Modified Chitosan-Based Gel Polymer Electrolytes Incorporated with Potassium Iodide

Molecules ◽  
2020 ◽  
Vol 25 (18) ◽  
pp. 4115 ◽  
Author(s):  
Aimi Mahirah Zulkifli ◽  
Nur Izzah Aqilah Mat Said ◽  
Shujahadeen Bakr Aziz ◽  
Elham Mohammed Ali Dannoun ◽  
Shameer Hisham ◽  
...  
Keyword(s):  
Solar Cells ◽  
Ionic Conductivity ◽  
Dielectric Permittivity ◽  
Polymer Electrolyte ◽  
Potassium Iodide ◽  
Polymer Electrolytes ◽  
Dye Sensitized Solar Cells ◽  
Gel Polymer Electrolytes ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

In the present work, phthaloyl chitosan (PhCh)-based gel polymer electrolytes (GPEs) were prepared using dimethylformamide (DMF) as a solvent, ethyl carbonate (EC) as a co-solvent, and a set of five quaternaries of potassium iodide (KI) as a doping salt, which is a mixed composition of iodine (I2). The prepared GPEs were applied to dye-sensitized solar cells (DSSC) to observe the effectiveness of the electrolyte, using mesoporous TiO2, which was sensitized with N3 dye as the sensitizer. The incorporation of the potassium iodide-based redox couple in a polymer electrolyte is fabricated for dye-sensitized solar cells (DSSCs). The number of compositions was based on the chemical equation, which is 1:1 for KI:I2. The electrical performance of prepared GPE systems have been assessed using electrical impedance spectroscopy (EIS), and dielectric permittivity. The improvement in the ionic conductivity of PhCh-based GPE was observed with the rise of salt concentration, and the maximum ionic conductivity (4.94 × 10−2 S cm−1) was achieved for the 0.0012 mol of KI:I2. The study of dielectric permittivity displays that ions with a high dielectric constant are associated with a high concentration of added ions. Furthermore, the gel polymer electrolyte samples were applied to DSSCs to detect the conversion effectiveness of the electrolytes. For electrolytes containing various content of KI:I2 the highest conversion efficiency (η%) of DSSC obtained was 3.57% with a short circuit current density (Jsc) of 20.33 mA cm−2, open-circuit voltage (Voc) of 0.37 V, fill factor (FF) of 0.47, as well as a conductivity of 2.08 × 10−2 S cm−1.

scholarly journals Effect of Modified Natural Filler O-Methylene Phosphonic κ-Carrageenan on Chitosan-Based Polymer Electrolytes

Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1910 ◽  
Author(s):  
Joy Liew ◽  
Kee Loh ◽  
Azizan Ahmad ◽  
Kean Lim ◽  
Wan Wan Daud
Keyword(s):  
Nuclear Magnetic Resonance ◽  
Tensile Strength ◽  
Infrared Spectroscopy ◽  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Solid Polymer Electrolyte ◽  
Solid Polymer ◽  
Solution Casting ◽  
Natural Filler

The potential for using O-methylene phosphonic κ-carrageenan (OMPk) as a filler in the chitosan-based polymer electrolyte N-methylene phosphonic chitosan (NMPC) was investigated. OMPk, a derivative of κ-carrageenan, was synthesized via phosphorylation and characterized using infrared spectroscopy (IR) and nuclear magnetic resonance (NMR). Both the IR and NMR results confirmed the phosphorylation of the parent carrageenan. The solid polymer electrolyte (SPE)-based NMPC was prepared by solution casting with different weight percentages of OMPk ranging from 2 to 8 wt %. The tensile strength of the polymer membrane increased from 18.02 to 38.95 MPa as the amount of OMPk increased to 6 wt %. However, the increase in the ionic conductivity did not match the increase in the tensile strength. The highest ionic conductivity was achieved with 4 wt % OMPk, which resulted in 1.43 × 10−5 Scm−1. The κ-carrageenan-based OMPk filler strengthened the SPE while maintaining an acceptable level of ionic conductivity.

scholarly journals Highly Conductive Redox-Couple Solid Polymer Electrolyte System: Blend-KI-I2 for Dye-Sensitized Solar Cells

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
Ravindra Kumar Gupta ◽  
Hee-Woo Rhee
Keyword(s):  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Solid Polymer Electrolyte ◽  
Dye Sensitized Solar Cells ◽  
Weight Fraction ◽  
Redox Couple ◽  
Solid Polymer ◽  
Equal Weight ◽  
Electrolyte System ◽  
Dye Sensitized

Ionic conductivity of a redox-couple solid polymer electrolyte system, () blend: [0.9KI : 0.1I2] with in weight fraction, is reported. A blend of poly(ethylene oxide) (abbreviated as PEO) and succinonitrile in equal weight fraction was used as a polymeric matrix instead of the PEO and succinonitrile because of its low-cost, electrical conductivity superior to the PEO, and thermal stability better than the succinonitrile. The electrolyte with showed ionic conductivity of S cm−1 and iodine ion diffusivity of nearly  cm2 s−1 at 25°C. The conductivity and diffusivity values were nearly two orders of magnitude higher than those of the PEO-KI-I2 due to the improved PEO crystallinity. It also exhibited dye-sensitized solar cell efficiency of 2.2% at 100 mW cm−2, which is twice of the cell prepared using the PEO-KI-I2 only.

scholarly journals Increased Ion Conductivity in Composite Solid Electrolytes With Porous Co3O4 Cuboids

2021 ◽  
Vol 8 ◽  
Author(s):  
Qiongyu Zhou ◽  
Songli Liu ◽  
Shiju Zhang ◽  
Yong Che ◽  
Li-Hua Gan
Keyword(s):  
Solid State ◽  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Composite Polymer Electrolyte ◽  
Composite Polymer ◽  
Composite Electrolyte ◽  
Base Interaction ◽  
Solid State Batteries ◽  
All Solid State Batteries

Compared with the fagile ceramic solid electrolyte, Li-ion conducting polymer electrolytes are flexible and have better contact with electrodes. However, the ionic conductivity of the polymer electrolytes is usually limited because of the slow segment motion of the polymer. In this work, we introduce porous Co3O4 cuboids to Poly (Ethylene Oxide)-based electrolyte (PEO) to investigate the influence of these cuboids on the ionic conductivity of the composite electrolyte and the performance of the all-solid-state batteries. The experiment results showed the porous cuboid Co3O4 fillers not only break the order motion of segments of the polymer to increase the amorphous phase amount, but also build Li+ continuous migration pathway along the Co3O4 surface by the Lewis acid-base interaction. The Li+ conductivity of the composite polymer electrolyte reaches 1.6 × 10−4 S cm−1 at 30°C. The good compatibility of the composite polymer electrolyte to Li metal anode and LiFePO4 cathode ensures good rate performance and long cycle life when applying in an all-solid-state LiFePO4 battery. This strategy points out the direction for developing the high-conducting composite polymer electrolytes for all-solid-state batteries.

Optimization of polymer electrolytes with the effect of concentration of additives in PEO-NH4HF2 polymer electrolytes

2020 ◽  
pp. 089270572093075
Author(s):  
Jitender Paul Sharma ◽  
Neelam Guleria
Keyword(s):  
Activation Energy ◽  
Dielectric Constant ◽  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Fumed Silica ◽  
Room Temperature ◽  
Testing Machine ◽  
Scanning Calorimetry ◽  
Nanocomposite Polymer

In the present work, nanocomposite polymer electrolyte films were prepared by solution casting technique using nanosized fumed silica to polyethylene oxide (PEO)-based polymer electrolytes containing ammonium bifluoride (NH4HF2). The ionic conductivity of 1.19 × 10−5 S cm−1 has been observed at room temperature (25°C) for 3 wt% fumed silica in PEO-10 wt% NH4HF2 polymer electrolytes after which the conductivity was observed to decrease. Furthermore, the addition of high dielectric constant plasticizer propylene carbonate (PC) in the optimized composition of nanocomposite polymer electrolytes has increased the number of charge carriers by the large dissolution of ionic salt, amorphous content, and hence the ionic conductivity. Maximum ionic conductivity obtained at room temperature was found to be 1.55 × 10−4 S cm−1 in the case of PEO-10 wt% NH4HF2-3 wt% fumed silica-0.3 (ml) PC polymer electrolytes which is five orders of magnitude higher than that of the polymer host material. Temperature-dependent ionic conductivity, activation energy, and dielectric constant studies have been described for all the compositions of polymer electrolytes. Ionic conductivity and dielectric constant studies were determined from impedance data. Polymer electrolytes containing both fumed silica and PC highlight that there is no phase transition in the polymer electrolyte and temperature dependence of ionic conductivity in the temperature range is of almost Arrhenius type. The lowest activation energy value for the highest conducting polymer electrolyte was found to be 0.172 eV. Change in melting temperature, % crystallinity ( χ c), and mechanical properties have also been observed in polymer electrolytes containing fumed silica as well as PC as studied by Differential Scanning Calorimetry/Thermogravimetric Analysis (DSC/TGA) and universal testing machine, respectively.

Impedance Behavior of Treated Methyl-Grafted Natural Rubber Polymer Electrolytes

2015 ◽  
Vol 1107 ◽  
pp. 217-222 ◽  
Author(s):  
Ahmad Fairoz Aziz ◽  
Khuzaimah Nazir ◽  
Siti Fadzilah Ayub ◽  
Rosnah Zakaria ◽  
Muhd Zu Azhan Yahya ◽  
...  
Keyword(s):  
Ionic Conductivity ◽  
Dielectric Permittivity ◽  
Natural Rubber ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Dissipation Factor ◽  
Dielectric Modulus ◽  
Aging Properties ◽  
Solution Cast ◽  
Cast Technique

Methyl-grafted natural rubber (MG30) was treated with N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine (6PPD) to enhance it anti-aging properties. The treated MG30 was used as polymer electrolyte by incorporating lithium trifluoromethane sulfonate (LiTF) through solution-cast technique. The impedance behavior of the sample has been carried out by analyzing the dielectric permittivity, dissipation factor, dielectric modulus and ionic conductivity as a function of temperature at different frequencies through impedance spectroscopy. Keywords: Methyl-grafted natural rubber, polymer electrolyte, N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine, ionic conductivity, dielectric.

Electrical Analysis of Cornstarch-Based Polymer Electrolyte Doped with NaCl

2017 ◽  
Vol 268 ◽  
pp. 347-351 ◽  
Author(s):  
Syakirah binti Shahrudin ◽  
Azizah Hanom Ahmad
Keyword(s):  
Ionic Conductivity ◽  
Polymer Electrolyte ◽  
Polymer Electrolytes ◽  
Room Temperature ◽  
Transport Number ◽  
Corn Starch ◽  
Solution Casting ◽  
Arrhenius Model ◽  
Casting Technique ◽  
Solution Casting Technique

Corn starch (CS) – sodium chloride (NaCl) based polymer electrolytes were prepared by solution casting technique. At room temperature, CS-NaCl film with ratio of 70 wt. % - 30 wt. % demonstrates the highest ionic conductivity in the range of (1.72 ± 0.12) x10-5 Scm-1. Temperature-dependence ionic conductivity study follows Arrhenius model and using related plot, the activation energy for highest conducting composition is 0.16eV. The transport number measurement studies confirmed that the ionic conductivity of this polymer electrolyte is due to ions. Fourier transform infrared spectroscopy (FTIR) analysis proved the interaction between CS and NaCl.

Sign in / Sign up

Export Citation Format

Share Document