scholarly journals Microstructure and Residual Stresses of AA2519 Friction Stir Welded Joints under Different Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 834
Author(s):  
Lucjan Śnieżek ◽  
Robert Kosturek ◽  
Marcin Wachowski ◽  
Bogusz Kania
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
Welded Joints ◽  
Precipitation Hardening ◽  
Cold Water ◽  
Traverse Speed ◽  
Welding Parameters ◽  
X Ray ◽  
Friction Stir ◽  
Treatment Conditions

The aim of this research was to investigate the effect of different heat treatment conditions of AA2519 friction stir welded joints on their microstructure and residual stresses. The following welding parameters have been used: 500 rpm tool rotation speed, 150 mm/min tool traverse speed, tool tilt angle 2°, pressure force 17 kN. The welded material was investigated in three different configurations: HT0, HT1, and HT2. The first type of weld (HT-0) was made using AA2519 alloy in non-precipitation hardened state and examined in such condition. The second type of weld (HT-1) has been performed on AA2519-T62, that corresponds to precipitation hardening condition. The last type of weld (HT2) was performed on annealed AA2519 and the obtained welds were subjected to the post-weld precipitation hardening process. The heat treatment was carried out in two stages: solution heat treatment (530 °C/2 h + cooling in cold water) and aging (165 °C/1 0 h). Residual stresses were measured using X-Ray diffraction patterns obtained from Bruker D8 Discover X-ray diffractometer utilizing the concepts of Euler cradle and polycapillary primary beam optics. The conducted research indicates that the best material properties: homogenous microstructure and uniform distribution of microhardness and compressive state of residual stresses were obtained for the HT-2 series samples subjected to heat treatment after the friction stir welding (FSW) process.

scholarly journals Friction Stir Welding Parameters: Impact of Abnormal Grain Growth during Post-Weld Heat Treatment on Mechanical Properties of Al–Mg–Si Welded Joints

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1607
Author(s):  
Amir Hossein Baghdadi ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar ◽  
Armin Rajabi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Friction Stir Welding ◽  
Grain Growth ◽  
Precipitation Hardening ◽  
Al Alloys ◽  
Abnormal Grain Growth ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir

Friction stir welding (FSW) is an alternative method to join aluminum (Al) alloys in a solid-state condition. However, the coarsening or dissolution of precipitation hardening phases in the welding zone causes strength reduction or softening behavior in the welded area of age-hardened Al alloys. Therefore, this research aimed to improve the mechanical properties of an FSW Al–Mg–Si alloy via post-weld heat treatment (PWHT) and the possibility of controlling the abnormal grain growth (AGG) using different welding parameters. FSW was performed with different rotational and travel speeds, and T6 heat treatment was carried out on the FSW samples as the PWHT. The results showed a decrease in the strength of the FSW samples compared with that of the base material (BM) due to the dissolution of precipitation hardening particles in the heat-affected zone. However, the emergence of AGG in the microstructure after the T6-PWHT was identified as the potential event in the microstructure of the PWHT samples. It is found that the AGG of the microstructure in similar joints of Al6061(T6) was governed by the welding parameters. The results proved that PWHT was able to increase the tensile properties of the welded samples to values comparable to that of Al6061(T6)-BM. The increased mechanical properties of the FSW joints were attributed to a proper PWHT that resulted in a homogeneous distribution of the precipitation hardening phases in the welding zones.

scholarly journals Mechanical Property Improvement in Dissimilar Friction Stir Welded Al5083/Al6061 Joints: Effects of Post-Weld Heat Treatment and Abnormal Grain Growth

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 288
Author(s):  
Amir Hossein Baghdadi ◽  
Zainuddin Sajuri ◽  
Azadeh Keshtgar ◽  
Nurulakmal Mohd Sharif ◽  
Armin Rajabi
Keyword(s):  
Heat Treatment ◽  
Mechanical Property ◽  
Grain Growth ◽  
Precipitation Hardening ◽  
Welded Joint ◽  
Abnormal Grain Growth ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir ◽  
Weld Heat

The 5083 and 6061(T6) aluminum (Al) alloys are widely used in transportation industries and the development of structural designs because of their high toughness and high corrosion resistance. Friction stir welding (FSW) was performed to produce the dissimilar welded joint of Al5083-Al 6061(T6) under different welding parameters. However, softening behavior occurred in the friction stir welded (FSWed) samples because of grain coarsening or the dissolution of precipitation-hardening phases in the welding zone. Consequently, this research intended to investigate the effect of the post-weld heat treatment (PWHT) method on the mechanical property improvement of the dissimilar FSWed Al5083-Al6061(T6) and governing abnormal grain growth (AGG) through different welding parameters. The results showed PWHT enhanced the mechanical properties of dissimilar joints of Al5083-Al6061(T6). AGG was obtained in the microstructure of PWHTed joints, but appropriate PWHT could recover the dissolved precipitation-hardening particle in the heat-affected zone of the as-welded joint. Further, the tensile strength of the dissimilar joint increased from 181 MPa in the as-welded joint to 270 MPa in the PWHTed joint, showing 93% welding efficacy.

scholarly journals X-ray Determination of Compressive Residual Stresses in Spring Steel Generated by High-Speed Water Quenching

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1154
Author(s):  
Diego E. Lozano ◽  
George E. Totten ◽  
Yaneth Bedolla-Gil ◽  
Martha Guerrero-Mata ◽  
Marcel Carpio ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
High Speed ◽  
Spring Steel ◽  
X Ray Diffraction ◽  
Laboratory Equipment ◽  
X Ray ◽  
Water Chamber ◽  
Hardened Case ◽  
Compressive Residual Stresses

Automotive components manufacturers use the 5160 steel in leaf and coil springs. The industrial heat treatment process consists in austenitizing followed by the oil quenching and tempering process. Typically, compressive residual stresses are induced by shot peening on the surface of automotive springs to bestow compressive residual stresses that improve the fatigue resistance and increase the service life of the parts after heat treatment. In this work, a high-speed quenching was used to achieve compressive residual stresses on the surface of AISI/SAE 5160 steel samples by producing high thermal gradients and interrupting the cooling in order to generate a case-core microstructure. A special laboratory equipment was designed and built, which uses water as the quenching media in a high-speed water chamber. The severity of the cooling was characterized with embedded thermocouples to obtain the cooling curves at different depths from the surface. Samples were cooled for various times to produce different hardened case depths. The microstructure of specimens was observed with a scanning electron microscope (SEM). X-ray diffraction (XRD) was used to estimate the magnitude of residual stresses on the surface of the specimens. Compressive residual stresses at the surface and sub-surface of about −700 MPa were obtained.

A Study of the Influence of Local Heat Treatment on the Structure of Welded Titanium Pipelines

2021 ◽  
Vol 410 ◽  
pp. 37-41
Author(s):  
Natalia A. Astafeva ◽  
Andrey A. Balanovskiy ◽  
Anna A. Pershina
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
Titanium Alloys ◽  
Welded Joints ◽  
Treatment Method ◽  
Local Heat ◽  
Optical Metallography ◽  
Heat Treated ◽  
Weld Structure ◽  
Heat Treatment Method

The article analyzes the results of a study of the influence of zonal heat treatment on the structure of welded joints of pipeline elements made of titanium alloys Ti-3.5Al-1.5Mn. In the manufacture of such structures, the TIG welding method is used to join pipe elements, after which the heat treatment method can be used to relieve residual stresses. The experiments have confirmed the effectiveness of zonal heat treatment preceded by welding. It was revealed that for welded joints made of titanium alloys, heat treatment can stabilize the structure. In experiments conducted by the method of optical metallography, the structure of heat treated and untreated welded joints was investigated. The influence of heat treatment on the weld structure and heat-affected zone was identified.

scholarly journals The Effect of Specimen Size on Residual Stresses in Friction Stir Welded Aluminum Components

2014 ◽  
Vol 996 ◽  
pp. 445-450 ◽  
Author(s):  
Wulf Pfeiffer ◽  
Eduard Reisacher ◽  
Michael Windisch ◽  
Markus Kahnert
Keyword(s):  
Residual Stresses ◽  
Specimen Size ◽  
Hole Drilling ◽  
X Ray Diffraction ◽  
X Ray ◽  
Friction Stir ◽  
Metal Parts ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
Drilling Method

Friction stir welding (FSW) is a well-known technique which allows joining of metal parts without severe distortion. Because FSW involves less heat input relative to conventional welding, it may be assumed that cutting specimens from larger friction stir welded components results in a negligible redistribution of residual stresses. The aim of the investigations was to verify these assumptions for a welded aluminum plate and a circumferentially-welded aluminum cylinder. Strain gage measurements, X-ray diffraction and the incremental hole drilling method were used.

scholarly journals Non-destructive Evaluation of Friction Stir Welded Joints by X-ray Radiography and Infrared Thermography

2014 ◽  
Vol 86 ◽  
pp. 469-475 ◽  
Author(s):  
T. Saravanan ◽  
B.B. Lahiri ◽  
K. Arunmuthu ◽  
S. Bagavathiappan ◽  
A.S. Sekhar ◽  
...  
Keyword(s):  
Infrared Thermography ◽  
Welded Joints ◽  
X Ray ◽  
Friction Stir ◽  
Non Destructive Evaluation ◽  
Non Destructive

A Study on Friction Stir Welding Process for AA2219/AA2195 Joints

2018 ◽  
Vol 762 ◽  
pp. 339-342
Author(s):  
Ho Sung Lee ◽  
Koo Kil No ◽  
Joon Tae Yoo ◽  
Jong Hoon Yoon
Keyword(s):  
Friction Stir Welding ◽  
Welded Joints ◽  
Rotation Speed ◽  
Microstructural Analysis ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Manufacturing Cost ◽  
Significant Saving ◽  
Friction Stir ◽  
Rotation Direction

The object of this study was to study mechanical properties of friction stir welded joints of AA2219 and AA2195. AA2219 has been used as an aerospace materials for many years primarily due to its high weldability and high specific strength in addition to the excellent cryogenic property so to be successfully used for manufacturing of cryogenic fuel tank for space launcher. Relatively new Aluminum-Lithium alloy, AA2195 provides significant saving on weight and manufacturing cost with application of friction stir welding. Friction stir welding is a solid-state joining process, which use a spinning tool to produce frictional heat in the work piece. To investigate the effect of the rotation direction of the tool, the joining was performed by switching the positions of the two dissimilar alloys. The welding parameters include the travelling speed, rotation speed and rotation direction of the tool, and the experiment was conducted under the condition that the travelling speed of the tool was 120-300 mm/min and the rotation speed of the tool was 400-800 rpm. Tensile tests were conducted to study the strength of friction stir welded joints and microhardness were measured with microstructural analysis. The results indicate the failure occurred in the relatively weaker TMAZ/HAZ interface of AA2219. The optimum process condition was obtained at the rotation speed of 600-800 rpm and the travelling speed of 180-240 mm/min.

Mechanical Behavior of Friction Stir Welded AA-6061 Thick Plates in Different Heat Treatment Conditions

2021 ◽  
Vol 875 ◽  
pp. 203-210
Author(s):  
Talha Ahmed ◽  
Wali Muhammad ◽  
Zaheer Mushtaq ◽  
Mustasim Billah Bhatty ◽  
Hamid Zaigham
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Treatment ◽  
Travel Speed ◽  
Butt Joint ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Joint Form

In this study, mechanical properties of friction stir welded Aluminum Alloy (AA) 6061 in three different heat treatment conditions i.e. Annealed (O), Artificially aged (T6) and Post Weld Heat Treated (PWHT) were compared. Plates were welded in a butt joint form. Parameters were optimized and joints were fabricated using tool rotational speed and travel speed of 500 rpm and 350 mm/min respectively. Two sets of plates were welded in O condition and out of which one was, later, subjected to post weld artificial aging treatment. Third set was welded in T6 condition. The welds were characterized by macro and microstructure analysis, microhardness measurement and mechanical testing. SEM fractography of the tensile fracture surfaces was also performed. Comparatively better mechanical properties were achieved in the plate with PWHT condition.

Sign in / Sign up

Export Citation Format

Share Document