scholarly journals Microwave Absorption Ability of Steel Slag and Road Performance of Asphalt Mixtures Incorporating Steel Slag

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 663 ◽  
Author(s):  
Baowen Lou ◽  
Zhuangzhuang Liu ◽  
Aimin Sha ◽  
Meng Jia ◽  
Yupeng Li
Keyword(s):  
Microwave Absorption ◽  
Steel Slag ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Microwave Absorber ◽  
Self Healing ◽  
High Temperature Stability ◽  
Road Performance ◽  
On The Road

Excessive usage of non-renewable natural resources and massive construction wastes put pressure on the environment. Steel slags, the main waste material from the metal industry, are normally added in asphalt concrete to replace traditional aggregate. In addition, as a typical microwave absorber, steel slag has the potential to transfer microwave energy into heat, thus increasing the limited self-healing ability of asphalt mixture. This paper aims to investigate the microwave absorption potentials of steel slag and the effect of its addition on road performance. The magnetic parameters obtained from a microwave vector network analyzer were used to estimate the potential use of steel slag as microwave absorber to heal cracks. Meanwhile, the initial self-healing temperature was further discussed according to the frequency sweeping results. The obvious porous structure of steel slag observed using scanning electron microscopy (SEM) had important impacts on the road performance of asphalt mixtures. Steel slag presented a worse effect on low-temperature crack resistance and water stability, while high-temperature stability can be remarkably enhanced when the substitution of steel slag was 60% by volume with the particle size of 4.75–9.5 mm. Overall, the sustainability of asphalt mixtures incorporating steel slag can be promoted due to its excellent mechanical and microwave absorption properties.

Laboratory Study of Pavement Performance of Basalt Fiber-Modified Asphalt Mixture

2011 ◽  
Vol 266 ◽  
pp. 175-179 ◽  
Author(s):  
Yuan Xun Zheng ◽  
Ying Chun Cai ◽  
Ya Min Zhang
Keyword(s):  
Asphalt Mixture ◽  
Basalt Fiber ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Polyester Fiber ◽  
Pavement Performance ◽  
High Temperature Stability ◽  
Modified Asphalt ◽  
And Control ◽  
Temperature Crack

In order to discuss the effect of the basalt fiber on reinforcing pavement performance of asphalt mixtures, the optimum dosage of asphalt and fibers were studied by the method of Marshall test and rut test firstly. Then pavement performances of basalt fiber-modified asphalt mixtures were investigated through tests of high temperature stability, water stability and low temperature crack resistance, and compared with that of polyester fiber, xylogen fiber and control mixture. The testing results showed that the pavement performance of fiber-modified asphalt mixture are improved and optimized comparing with control asphalt mixture, and the performance of basalt fiber-modified asphalt mixture with best composition were excelled than those of polyester fiber and xylogen fiber.

scholarly journals Study on Laboratory Experimental Pavement Performances of SEAM Modified Asphalt Mixture

2019 ◽  
Vol 136 ◽  
pp. 03010
Author(s):  
Ma Qingna ◽  
Zhao Zhiqin ◽  
Xu Qian ◽  
Sun Feng
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Water Stability ◽  
High Temperature Stability ◽  
Modified Asphalt ◽  
The Road ◽  
Road Performance ◽  
Property Index

Adding sulphur dilution asphalt modifier SEAM to asphalt mixture is not only a modifier of asphalt mixture, but also an additive of asphalt mixture. When the modifier is added into the asphalt mixture, the road performance of the asphalt mixture can be improved. This paper studies SEAM modified asphalt mixture the Marshall property index, temperature stability, Water stability and fatigue feature in the Laboratory. On the based of the result of the experiment and analysis, SEAM can improve the high temperature stability, Water stability and fatigue feature. But the low temperature stability can’t improve.

Research on the Road Performance of the AC-25 Asphalt Mixtures

2012 ◽  
Vol 204-208 ◽  
pp. 1593-1598
Author(s):  
Hong Mei Li ◽  
Wen Fang Liu
Keyword(s):  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Central Layer ◽  
The Road ◽  
Road Performance ◽  
On The Road

In this paper, firstly, based on asphalt pavement central layer, the comparison with the foreign related gradation of asphalt mixtures, one typical kinds of gradations are decided; Secondly, the asphalt aggregate ratio is predicted based on professor Lin’s Theory , and five asphalt aggregate ratio are selected. Finally, the road performance of asphalt mixture is experimented, and the road performance of five asphalt aggregate ratio is analyzed. As a result, we can predict the range of the optimum asphalt aggregate ratio based on the road performance.

The Analyze Study of Compacting Temperature and Road Performance of Warm Mix Asphalt Mixture (LEADCAP)

2013 ◽  
Vol 361-363 ◽  
pp. 1681-1688 ◽  
Author(s):  
Hai Sheng Zhao ◽  
Wei Chen ◽  
Xiao Yan Wang
Keyword(s):  
Low Temperature ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Organic Additive ◽  
Bending Test ◽  
High Temperature Stability ◽  
The Road ◽  
Indirect Tension ◽  
Road Performance

This paper used one kind of organic additive LEADCAP to reduce the compacting temperature of SBS WMA mixture, and compared the WMA mixture compacted by superpave gyratory compactor (SGC) with HMA mixture to determine the compacting temperature of WMA mixture. Rutting test, low temperature bending test, freeze-thaw indirect tension test, Hamburg Wheel-Track test and dynamic modulus were carried out to evaluate the road performance of WMA mixed with LEASCAP. The test result showed that the WMA mixed with LEADCAP had well performed high temperature stability, low temperature stability, water stability, rutting cracking resistance, and high dynamic modulus, the compacting temperature were 127 °C, and affectively reduced the compacting temperature of SBS WMA mixture.

Study of Road Property of Basalt Fiber Asphalt Concrete

2012 ◽  
Vol 238 ◽  
pp. 22-25 ◽  
Author(s):  
Yuan Zhao Chen ◽  
Zhen Xia Li
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Basalt Fiber ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Polyester Fiber ◽  
Pavement Performance ◽  
High Temperature Stability ◽  
Reference Mixture ◽  
Temperature Crack

In order to discuss the effectiveness of basalt fiber in reinforcing pavement performance of asphalt mixtures, the pavement performances of basalt fiber asphalt mixtures were investigated by tests of high temperature stability, water stability and low temperature crack resistance, and compared with the pavement performance of asphalt mixtures with polyester fiber and xylogen fiber, and that of reference mixture. The results show that pavement performance of fiber asphalt mixture are improved and optimized comparing with reference asphalt mixture, the performance of asphalt mixture with basalt fiber are excelled than those with polyester fiber and xylogen fiber while the dosage of fibers is keeping at the optimum.

scholarly journals Study of the Self-Healing Performance of Semi-Flexible Pavement Materials Grouted with Engineered Cementitious Composites Mortar based on a Non-Standard Test

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3488 ◽  
Author(s):  
Cai ◽  
Huang ◽  
Wu
Keyword(s):  
Flexural Strength ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Flexible Pavement ◽  
Standard Test ◽  
The Self ◽  
Cementitious Composites ◽  
Self Healing ◽  
High Temperature Stability ◽  
Engineered Cementitious Composites

Semi-flexible pavement (SFP) materials, with their characteristics of good high temperature stability, strong durability, and lower cost, are suitable for heavy-duty roads, but their cracking problem has hindered the development and popularization of this kind of pavement to a certain extent. In this study, engineered cementitious composites (ECC) were used to form ECC-SFP materials. The self-healing properties of ECC-SFP materials with three kinds of voids of matrix asphalt mixtures were studied. The test results showed that the fluidity and strength of the ECC mortars met the specification requirements when the water–cement ratio was 0.23 and the ECC fiber dosage was 1–2%. The flexural strength of ECC mortar is better than that of ordinary mortar. The higher the ECC fiber dosage, the higher the flexural strength. Increasing the void of the matrix asphalt mixture and the amount of ECC mortar increased the toughness of the ECC-SFP material, which was seen as an increase of the flow value. Curing conditions are key factor affecting the self-healing properties of ECC mortar and ECC-SFP materials. The self-healing effect of materials in 60 °C water is the best. When an ECC fiber dosage of 1% was used, the HImor of ECC mortar and HImix of ECC-SFP material were 27.5% and 24.8%, respectively. With the addition of ECC material, ECC-SFP material achieved a certain degree of self-healing, but this still needs to be further optimized. Studies of grouting process optimization and increasing the ECC fiber dosage are feasible directions to explore in order to improve the self-healing properties of ECC-SFP materials in the future.

Research on the Paving Performance of Montmorillonite/SBS Modified Asphalt Mixtures

2012 ◽  
Vol 204-208 ◽  
pp. 4143-4146
Author(s):  
Zhong Guo He ◽  
Xin De Tang ◽  
Wen Jun Yin ◽  
Yi Fan Sun ◽  
Zhong Bo Liu
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
High Temperature Stability ◽  
Moisture Susceptibility ◽  
Modified Asphalt ◽  
Sbs Modified Asphalt ◽  
Enhanced Stability

Montmorillonite/SBS composite modifed asphalts were prepared by mixing montmorillonite with SBS-modified asphalt, further the corresponding asphalt mixtures were obtained. The paving technical indexes of the mixture such as physical properties, moisture suscepyibility, and high temperature stability were tested, and compared with that of the corresponding SBS-modifed asphalt mixture and base asphalt mixture. The results demonstrate that the montmorillonite/SBS composite modifed asphalt mixture exhibites enhanced stability, improved flow value and moisture susceptibility, and increased high temperature stability.

scholarly journals Feasibility Evaluation of Preparing Asphalt Mixture with Low-Grade Aggregate, Rubber Asphalt and Desulphurization Gypsum Residues

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1481 ◽  
Author(s):  
Xiaoliang Zhang ◽  
Ben Zhang ◽  
Huaxin Chen ◽  
Dongliang Kuang
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Crack Resistance ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Limestone Powder ◽  
Low Grade ◽  
High Temperature Stability ◽  
Temperature Crack

Road construction consumes great amounts of high-grade natural resources. Using low-grade natural rocks or some solid wastes as substitute materials is a hot topic. Considering this, the feasibility of using low-grade granite aggregate, solid waste-based filler (desulphurization gypsum residues, DGR) and binder (waste tire rubber modified asphalt, RMA) simultaneously in asphalt mixtures has been fully investigated in this research. The commonly used base asphalt and limestone powder (LP) filler were control groups. Material characteristics of raw materials mainly including micro-morphology, functional group, mineral phase, chemical composition and thermal stability were first evaluated in order to recognize them. Four asphalt mixtures (two asphalt binder and two filler) were then designed by standard Superpave method. Finally, a detailed investigation into the pavement performance of asphalt mixtures was carried out. The moisture damage resistance and low-temperature crack resistance were detected by the changing rules of stability, strength and fracture energy, and the high-temperature stability and fatigue performance were determined by wheel tracking test and indirect tensile (IDT) fatigue test, respectively. Results suggested that RMA and DGR both showed positive effects on the low-temperature crack resistance and fatigue property of the granite asphalt mixture. DGR also strengthened moisture stability. The contribution of RMA on high-temperature deformation resistance of the granite asphalt mixture was compelling. It can offset the insufficiency in high-temperature stability made by DGR. A conclusion can be made that asphalt mixture prepared with granite, DGR and RMA possesses satisfactory pavement performances.

scholarly journals Optimizing Gradation Design for Ultra-Thin Wearing Course Asphalt

Materials ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 189 ◽  
Author(s):  
Wentian Cui ◽  
Kuanghuai Wu ◽  
Xu Cai ◽  
Haizhu Tang ◽  
Wenke Huang
Keyword(s):  
High Temperature ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Wear Test ◽  
Asphalt Mixtures ◽  
Skid Resistance ◽  
High Temperature Stability ◽  
Functional Layer ◽  
Rutting Resistance ◽  
Road Surfaces

In recent years, ultra-thin wearing course asphalt mixture has been widely used in the reconstruction of old road surfaces and the functional layer of new road surfaces due to its good road performance. To improve the rutting resistance of ultra-thin wearing course asphalt mixture, this research presents an Ultra-thin Wearing Course-10 (UTWC-10) asphalt mixture with good high-temperature stability and skid resistance based on the Taylor system standard mesh specifications. The Course Aggregate Void Filling (CAVF) method is used to design the UTWC-10 asphalt mixture, which is compared with two other traditional ultra-thin wearing course asphalt mixtures on the basis of different laboratory performance tests. The high-temperature rutting test data shows that the rutting dynamic stability (DS) index of the UTWC-10 asphalt mixture is much higher than that of traditional wearing course asphalt mixtures, as it has better high-temperature stability. Moreover, anti-sliding performance attenuation tests are conducted by a coarse aggregate polishing machine. The wear test results show that the skid resistance of the UTWC-10 asphalt mixture is promising. The anti-sliding performance attenuation test can effectively reflect the skid resistance attenuation trend of asphalt pavement at the long-term vehicle load. It is verified that the designed UTWC-10 asphalt mixture shows excellent high-temperature rutting resistance and skid resistance, as well as better low temperature crack resistance and water stability than the traditional wearing course asphalt mixtures.

scholarly journals Properties of a Steel Slag–Permeable Asphalt Mixture and the Reaction of the Steel Slag–Asphalt Interface

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3603 ◽  
Author(s):  
Wenhuan Liu ◽  
Hui Li ◽  
Huimei Zhu ◽  
Pinjing Xu
Keyword(s):  
Mineral Composition ◽  
Asphalt Pavement ◽  
Steel Slag ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Tricalcium Silicate ◽  
Dicalcium Silicate ◽  
High Temperature Stability ◽  
X Ray ◽  
Marshall Stability

Steel slag is an industrial solid waste with the largest output in the world. It has the characteristics of wear resistance, good particle shape, large porosity, etc. At the same time, it has good adhesion characteristics with asphalt. If steel slag is used in asphalt pavement, it not only solves the problem of insufficient quality aggregates in asphalt concrete, but can also give full play to the high hardness and high wear resistance of steel slag to improve the performance of asphalt pavement. In this study, a steel slag aggregate was mixed with road petroleum asphalt to prepare a permeable steel slag–asphalt mixture, which was then compared with the permeable limestone–asphalt mixture. According to the Technical Regulations for Permeable Asphalt Pavement (CJJT 190-2012), the permeability, water stability, and Marshall stability of the prepared asphalt mixtures were tested and analyzed. In addition, the high-temperature stability and expansibility were analyzed according to the Experimental Regulations for Highway Engineering Asphalt and Asphalt Mixture (JTG E20-2011). The chemical composition of the steel slag was tested and analyzed by X-ray fluorescence spectrometer (XRF). The mineral composition of the steel slag was tested and analyzed by X-ray diffractometer (XRD). The asphalt was analyzed by Fourier transform infrared spectroscopy (FTIR). The results show that the steel slag asphalt permeable mixture had good permeability, water stability, and Marshall stability, as well as good high-temperature stability and a low expansion rate. The main mineral composition was ferroferric oxide, the RO phase (RO phase is a broad solid solution formed by melting FeO, MgO, and other divalent metal oxides such as MnO), dicalcium silicate, and tricalcium silicate. In the main chemical composition of steel slag, there was no chemical reaction between aluminum oxide, calcium oxide, silicon dioxide, and asphalt, while ferric oxide chemically reacted with asphalt and formed new organosilicon compounds. The main mineral composition of the steel slag (i.e., triiron tetroxide, dicalcium silicate, and tricalcium silicate) reacted chemically with the asphalt and produced new substances. There was no chemical reaction between the RO phase and asphalt.

Sign in / Sign up

Export Citation Format

Share Document