scholarly journals Considerations on the Applicability of Test Methods for Mechanical Characterization of Materials Manufactured by FDM

Materials ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 28 ◽  
Author(s):  
Amabel García-Domínguez ◽  
Juan Claver ◽  
Ana María Camacho ◽  
Miguel A. Sebastián
Keyword(s):  
Additive Manufacturing ◽  
Mechanical Characterization ◽  
Test Methods ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
General Test ◽  
Specific Standard ◽  
Characterization Of Materials ◽  
Definition Of

The lack of specific standards for characterization of materials manufactured by Fused Deposition Modelling (FDM) makes the assessment of the applicability of the test methods available and the analysis of their limitations necessary; depending on the definition of the most appropriate specimens on the kind of part we want to produce or the purpose of the data we want to obtain from the tests. In this work, the Spanish standard UNE 116005:2012 and international standard ASTM D638–14:2014 have been used to characterize mechanically FDM samples with solid infill considering two build orientations. Tests performed according to the specific standard for additive manufacturing UNE 116005:2012 present a much better repeatability than the ones according to the general test standard ASTM D638–14, which makes the standard UNE more appropriate for comparison of different materials. Orientation on-edge provides higher strength to the parts obtained by FDM, which is coherent with the arrangement of the filaments in each layer for each orientation. Comparison with non-solid specimens shows that the increase of strength due to the infill is not in the same proportion to the percentage of infill. The values of strain to break for the samples with solid infill presents a much higher deformation before fracture.

Mechanical characterization of 3D printed, non-planar lattice structures under quasi-static cyclic loading

2020 ◽  
Vol 26 (4) ◽  
pp. 707-717 ◽  
Author(s):  
John C.S. McCaw ◽  
Enrique Cuan-Urquizo
Keyword(s):  
Additive Manufacturing ◽  
Cyclic Loading ◽  
Fused Deposition Modeling ◽  
Mechanical Characterization ◽  
Complex Geometries ◽  
Lattice Structures ◽  
Planar Lattice ◽  
Content Type ◽  
Fused Deposition

Purpose While additive manufacturing via melt-extrusion of plastics has been around for more than several decades, its application to complex geometries has been hampered by the discretization of parts into planar layers. This requires wasted support material and introduces anisotropic weaknesses due to poor layer-to-layer adhesion. Curved-layer manufacturing has been gaining attention recently, with increasing potential to fabricate complex, low-weight structures, such as mechanical metamaterials. This paper aims to study the fabrication and mechanical characterization of non-planar lattice structures under cyclic loading. Design/methodology/approach A mathematical approach to parametrize lattices onto Bèzier surfaces is validated and applied here to fabricate non-planar lattice samples via curved-layer fused deposition modeling. The lattice chirality, amplitude and unit cell size were varied, and the properties of the samples under cyclic-loading were studied experimentally. Findings Overall, lattices with higher auxeticity showed less energy dissipation, attributed to their bending-deformation mechanism. Additionally, bistability was eliminated with increasing auxeticity, reinforcing the conclusion of bending-dominated behavior. The analysis presented here demonstrates that mechanical metamaterial lattices such as auxetics can be explored experimentally for complex geometries where traditional methods of comparing simple geometry to end-use designs are not applicable. Research limitations/implications The mechanics of non-planar lattice structures fabricated using curved-layer additive manufacturing have not been studied thoroughly. Furthermore, traditional approaches do not apply due to parameterization deformations, requiring novel approaches to their study. Here the properties of such structures under cyclic-loading are studied experimentally for the first time. Applications for this type of structures can be found in areas like biomedical scaffolds and stents, sandwich-panel packaging, aerospace structures and architecture of lattice domes. Originality/value This work presents an experimental approach to study the mechanical properties of non-planar lattice structures via quasi-static cyclic loading, comparing variations across several lattice patterns including auxetic sinusoids, disrupted sinusoids and their equivalent-density quadratic patterns.

Additive manufacturing of an automotive brake pedal by metal fused deposition modelling

2021 ◽  
Author(s):  
M.I.M. Sargini ◽  
S.H. Masood ◽  
Suresh Palanisamy ◽  
Elammaran Jayamani ◽  
Ajay Kapoor
Keyword(s):  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Brake Pedal ◽  
Fused Deposition ◽  
Automotive Brake

MECHANICAL CHARACTERIZATION OF MATERIALS AND DIAGNOSIS OF STRUCTURES BY INVERSE ANALYSES: SOME INNOVATIVE PROCEDURES AND APPLICATIONS

2014 ◽  
Vol 11 (03) ◽  
pp. 1343002 ◽  
Author(s):  
GIULIO MAIER ◽  
VLADIMIR BULJAK ◽  
TOMASZ GARBOWSKI ◽  
GIUSEPPE COCCHETTI ◽  
GIORGIO NOVATI
Keyword(s):  
Structural Analysis ◽  
Digital Image Correlation ◽  
Residual Stresses ◽  
Mechanical Characterization ◽  
Image Correlation ◽  
Alkali Silica Reaction ◽  
Compression Tests ◽  
Material Models ◽  
Characterization Of Materials

A survey is presented herein of some recent research contributions to the methodology of inverse structural analysis based on statical tests for diagnosis of possibly damaged structures and for mechanical characterization of materials in diverse industrial environments. The following issues are briefly considered: identifications of parameters in material models and of residual stresses on the basis of indentation experiments; mechanical characterization of free-foils and laminates by cruciform and compression tests and digital image correlation measurements; diagnosis, both superficially and in depth, of concrete dams, possibly affected by alkali-silica-reaction or otherwise damaged.

scholarly journals Automated Testing and Characterization of Additive Manufacturing (ATCAM)

2021 ◽  
Author(s):  
Arash Alex Mazhari ◽  
Randall Ticknor ◽  
Sean Swei ◽  
Stanley Krzesniak ◽  
Mircea Teodorescu
Keyword(s):  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Cell System ◽  
Automated Testing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Machine Calibration

AbstractThe sensitivity of additive manufacturing (AM) to the variability of feedstock quality, machine calibration, and accuracy drives the need for frequent characterization of fabricated objects for a robust material process. The constant testing is fiscally and logistically intensive, often requiring coupons that are manufactured and tested in independent facilities. As a step toward integrating testing and characterization into the AM process while reducing cost, we propose the automated testing and characterization of AM (ATCAM). ATCAM is configured for fused deposition modeling (FDM) and introduces the concept of dynamic coupons to generate large quantities of basic AM samples. An in situ actuator is printed on the build surface to deploy coupons through impact, which is sensed by a load cell system utilizing machine learning (ML) to correlate AM data. We test ATCAM’s ability to distinguish the quality of three PLA feedstock at differing price points by generating and comparing 3000 dynamic coupons in 10 repetitions of 100 coupon cycles per material. ATCAM correlated the quality of each feedstock and visualized fatigue of in situ actuators over each testing cycle. Three ML algorithms were then compared, with Gradient Boost regression demonstrating a 71% correlation of dynamic coupons to their parent feedstock and provided confidence for the quality of AM data ATCAM generates.

Animal orthosis fabrication with additive manufacturing – a case study of custom orthosis for chicken

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wiktoria Maria Wojnarowska ◽  
Jakub Najowicz ◽  
Tomasz Piecuch ◽  
Michał Sochacki ◽  
Dawid Pijanka ◽  
...  
Keyword(s):  
Veterinary Medicine ◽  
Additive Manufacturing ◽  
Computer Aided Design ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Secondary Objective ◽  
Traditional Manufacturing ◽  
Aided Design

Purpose Chicken orthoses that cover the ankle joint area are not commercially available. Therefore, the main purpose of this study is to fabricate a customised temporary Ankle–Foot Orthosis (AFO) for a chicken with a twisted ankle using computer-aided design (CAD) and three-dimensional (3D) printing. The secondary objective of the paper is to present the specific application of Additive Manufacturing (AM) in veterinary medicine. Design/methodology/approach The design process was based on multiple sketches, photos and measurements that were provided by the owner of the animal. The 3D model of the orthosis was made with Autodesk Fusion 360, while the prototype was fabricated using fused deposition modelling (FDM). Evaluation of the AFO was performed using the finite element method. Findings The work resulted in a functional 3D printed AFO for chicken. It was found that the orthosis made with AM provides satisfactory stiffen and a good fit. It was concluded that AM is suitable for custom bird AFO fabrication and, in some respects, is superior to traditional manufacturing methods. It was also concluded that the presented procedure can be applied in other veterinary cases and to other animal species and other parts of their body. AM provides veterinary with a powerful tool for the production of well-fitted and durable orthoses for animals. Research limitations/implications The study does not include the chicken's opinion on the comfort or fit of the manufactured AFO due to communication issues. Evaluation of the final prototype was done by the researchers and the animal owner. Originality/value No evidence was found in the literature on the use of AM for chicken orthosis, so this study is the first to describe such an application of AM. In addition, the study demonstrates the value of AM in veterinary medicine, especially in the production of devices such as orthoses.

scholarly journals Strength Comparison of FDM 3D Printed PLA Made by Different Manufacturers

TEM Journal ◽  
2020 ◽  
pp. 966-970
Author(s):  
Damir Hodžić ◽  
Adi Pandžić ◽  
Ismar Hajro ◽  
Petar Tasić
Keyword(s):  
Experimental Study ◽  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Manufacturing Technique ◽  
Plastic Materials ◽  
Wide Range ◽  
3D Printed ◽  
The Difference ◽  
Printing Parameters

Widely used additive manufacturing technique for plastic materials is Fused Deposition Modelling (FDM). The FDM technology has gained interest in industry for a wide range of applications, especially today when large number of different materials on the market are available. There are many different manufacturers for the same FDM material where the difference in price goes up to 50%. This experimental study investigates possible difference in strength of the 3D printed PLA material of five different manufacturers. All specimens are 3D printed on Ultimaker S5 printer with the same printing parameters, and they are all the same colour.

Sign in / Sign up

Export Citation Format

Share Document