scholarly journals Machinability Study of Hardened 1045 Steel When Milling with Ceramic Cutting Inserts

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3974 ◽  
Author(s):  
Mohamed Shnfir ◽  
Oluwole A. Olufayo ◽  
Walid Jomaa ◽  
Victor Songmene
Keyword(s):  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Mechanical Shock ◽  
Tool Edge ◽  
Aisi 1045 ◽  
High Feed ◽  
1045 Steel ◽  
Edge Preparation

Intermittent machining using ceramic tools such as hard milling is a challenging task due to the severe mechanical shock that the inserts undergo during machining and the brittleness of ceramic inserts. This study investigates the machinability of hardened steel AISI 1045 during face milling using SiAlON and whisker (SiCW) based ceramic inserts. The main focus seeks to identify the effects of cutting parameters, milling configuration, edge preparation and work material hardness on machinability indicators such as resultant cutting force, power consumption and flank tool wear. The effects of these varying cutting conditions on performance characteristics were investigated using a Taguchi orthogonal array design L32 (21 44) and evaluated using ANOVA. Results indicate lower resultant cutting forces were recorded with honed edge inserts of SiAlON ceramic grade. In addition, a decrease in resultant cutting forces was associated with reduced feed rates and increased hardness. The feed rate and cutting speed were also identified as the greatest influencing factors in the amount of cutting power. The main wear mechanisms responsible for flank wear on the ceramic inserts are micro-scale abrasion and micro-chipping. Increased flank wear was observed at low cutting speed and high feed rates, while micro-chipping mostly ensued from the cyclic loading of the radial tool edge form, which is more susceptible to impact fragmentation. Thus, the use of tools with chamfered tool-edge preparation greatly improved observed wear values. Additional confirmation tests were also conducted to validate the results of the tests.

scholarly journals Online Tool Wear Monitoring by the Analysis of Cutting Forces in Transient State for Dry Machining of Ti6Al4V Alloy

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1014 ◽  
Author(s):  
Sánchez Hernández ◽  
Trujillo Vilches ◽  
Bermudo Gamboa ◽  
Sevilla Hurtado
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Transient State ◽  
Cutting Parameters ◽  
Dry Machining ◽  
Crater Wear ◽  
Force Amplitude

In this work, the analysis of the cutting speed and feed rate influence on tool wear and cutting forces in Ti6Al4V alloy dry machining is presented. The study has been focused on the machining in a transient state. The tool wear mechanisms, tool wear intensity and cutting forces evolution have been analyzed as a function of the cutting parameters. Experimental results show that the main cutting force amplitude exhibits a general trend to increase with both cutting parameters. Crater wear was more evident at high cutting speeds, whereas flank wear was present on the whole interval of the cutting parameters analyzed. Furthermore, the cutting speed shows a slightly higher influence on crater wear and the feed rate shows a higher influence on flank wear. Finally, several experimental parametric models have been obtained. These models allow predicting the evolution of crater and flank tool wear, as well as the cutting forces, as a function of the cutting parameters. Additionally, a model that allows monitoring the tool wear on the machining transient state as a function of the main cutting force amplitude has been developed.

scholarly journals An Investigation into the Effect of Electro-Contact Heating in the Machining of Low-Rigidity Thin-Walled Micro-Machine Parts

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4427
Author(s):  
Antoni Świć ◽  
Arkadiusz Gola ◽  
Olga Orynycz ◽  
Karol Tucki
Keyword(s):  
Control System ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Contact Heating ◽  
Thin Walled ◽  
Micro Machine

Low-rigidity thin-walled parts are components of many machines and devices, including high precision electric micro-machines used in control and tracking systems. Unfortunately, traditional machining methods used for machining such types of parts cause a significant reduction in efficiency and in many cases do not allow obtaining the required accuracy parameters. Moreover, they also fail to meet modern automation requirements and are uneconomical and inefficient. Therefore, the aim of provided studies was to investigate the dependency of cutting forces on cutting parameters and flank wear, as well as changes in cutting forces induced by changes in heating current density and machining parameters during the turning of thin-walled parts. The tests were carried out on a specially designed and constructed turning test stand for measuring cutting forces and temperature at specific cutting speed, feed rate, and depth of cut values. As part of the experiments, the effect of cutting parameters and flank wear on cutting forces, and the effect of heating current density and turning parameters on changes in cutting forces were analyzed. Moreover, the effect of cutting parameters (depth of cut, feed rate, and cutting speed) on temperature has been determined. Additionally, a system for controlling electro-contact heating and investigated the relationship between changes in cutting forces and machining time in the operations of turning micro-machine casings with and without the use of the control system was developed. The obtained results show that the application of an electro-contact heating control system allows to machine conical parts and semi-finished products at lower cutting forces and it leads to an increase in the deformation of the thin-walled casings caused by runout of the workpiece.

scholarly journals Effect of Cutting Parameters on Tool-Chip Interface Temperature in an Orthogonal Turning Process

2014 ◽  
Vol 903 ◽  
pp. 21-26 ◽  
Author(s):  
Shamsuddin Sulaiman ◽  
Amir Roshan ◽  
Soroosh Borazjani
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Interface Temperature ◽  
Machined Surface ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

The aim of this paper is to investigate the effect of cutting speed and uncut chip thickness on cutting performance. A Finite Element Method (FEM) based on the ABAQUS explicit software which involves Johnson-Cook material mode and Coulombs friction law was used to simulate of High Speed Machining (HSM) of AISI 1045 steel. In this simulation work, feed rate ranging from 0.05 mm/rev to 0.13 mm/rev and cutting speed ranging from 200 m/min to 600 m/min at three different cutting speeds were investigated. From the simulation results it was observed that increasing feed rate and cutting speed lead to increase temperature and stress distribution at tool/chip interface. The results obtained from this study are highly essential to predict machining induced residual stresses and thermo-mechanical deformation related properties on the machined surface.

Microscopic Studies of Flank Wear on Alumina Tools

1991 ◽  
Vol 113 (1) ◽  
pp. 204-209 ◽  
Author(s):  
Sukyoung Kim ◽  
Delcie R. Durham
Keyword(s):  
Flank Wear ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Physical And Mechanical Properties ◽  
Thermal Conditions ◽  
Mechanical Wear ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Flank Surface ◽  
Aisi 4340

The flank wear of alumina cutting tools in the machining of annealed steels, AISI 1045 and 4340, which were approximately the same hardness, was studied microscopically. The intent was to establish whether any chemical wear occurred in addition to the mechanical wear on the flank surface. While the hardness of the two steels was essentially the same, the chemistry and the carbide present in the microstructure differed. The flank wear morphology was studied and three regions within the wear land could be defined. The flank wear of the alumina tools, which increased with an increase of cutting speeds, was found to be strongly dependent upon the chemistry of the work material being machined. At the higher speeds, the flank wear when cutting AISI 1045 steel was approximately twice that of AISI 4340. It was observed that different wear mechanisms could be associated with the material being machined. The thermally activated chemical and mechanical wear processes were predominant in the AISI 1045 machining, but the chemical wear was not significant in machining AISI 4340. At lower temperatures, the mechanical wear predominated for both steels. The wear pattern consisted of three regions on the flank wear surface, which varied with cutting speed, cutting distance, and position within the wear land. The surface roughness on the worn tool was also related to these same test parameters. The flank wear appears to depend upon not only the workpiece, but also upon an interfacial oxide layer that forms during cutting. The physical and mechanical properties of the interfacial oxide depend upon its constituents, which relate back to workpiece composition and thermal conditions at the interface.

Modeling of Stresses and Temperature in Turning Using Finite Element Method

2013 ◽  
Vol 307 ◽  
pp. 174-177 ◽  
Author(s):  
Kuldip Singh Sangwan ◽  
Girish Kant ◽  
Aditya Deshpande ◽  
Pankaj Sharma
Keyword(s):  
Finite Element ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Machining Parameters ◽  
Effective Stresses ◽  
Wide Range ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

This paper focuses on finite element modeling of orthogonal cutting process of AISI 1045 steel using Modified Johnson Cook (MJC) as constitutive material flow model under various machining parameters. Finite element solutions of cutting forces, effective stresses and temperature are obtained for a wide range of cutting speeds and feeds. The effect of feed and cutting speed on cutting forces, effective stresses and temperature has been studied over a wide range of values. Percentage variation of each is also studied to predict co-relation with the different machining parameters.

scholarly journals Influence of Tool Wear on Form Deviations in Dry Machining of UNS A97075 Alloy

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 958
Author(s):  
Francisco Javier Trujillo Vilches ◽  
Sergio Martín Béjar ◽  
Carolina Bermudo Gamboa ◽  
Manuel Herrera Fernández ◽  
Lorenzo Sevilla Hurtado
Keyword(s):  
Tool Wear ◽  
General Trend ◽  
Cutting Speed ◽  
Main Tool ◽  
Cutting Parameters ◽  
Adhesion Wear ◽  
Tool Wear Mechanisms ◽  
Tool Wear Mechanism ◽  
High Feed ◽  
Dry Conditions

Geometrical tolerances play a very important role in the functionality and assembly of parts made of light alloys for aeronautical applications. These parts are frequently machined in dry conditions. Under these conditions, the tool wear becomes one of the most important variables that influence geometrical tolerances. In this work, the influence of tool wear on roundness, straightness and cylindricity of dry-turned UNS A97075 alloy has been analyzed. The tool wear and form deviations evolution as a function of the cutting parameters and the cutting time has been assessed. In addition, the predominant tool wear mechanisms have been checked. The experimental results revealed that the indirect adhesion wear (BUL and BUE) was the main tool-wear mechanism, with the feed being the most influential cutting parameter. The combination of high feed and low cutting speed values resulted in the highest tool wear. The analyzed form deviations showed a general trend to increase with both cutting parameters. The tool wear and the form deviations tend to increase with the cutting time only within the intermediate range of feed tested. As the main novelty, a relationship between the cutting parameters, the cutting time (and, indirectly, the tool wear) and the analyzed form deviations has been found.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

Influence of the Cutting Parameters on the Cutting Forces of Carbon Steel

2002 ◽  
Author(s):  
Zulay Cassier ◽  
Patricia Mun˜oz-Escanola ◽  
Rolda´n Sa´nchez
Keyword(s):  
Carbon Steel ◽  
Cutting Forces ◽  
Low Cost ◽  
Cutting Parameters ◽  
Carbon Steels ◽  
Machining Process ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 1045 ◽  
Alloy Steels

Plain carbon steels and alloy steels have a great application in the manufacturing process especially due to their characteristic of high machinability and low cost. The machining of these materials, the study of the cutting forces, and the power required for the cutting process is one of the most important parameters to be evaluated. The relationship between this parameter and the other cutting variables process is crucial for the optimization of the machining process. The results of this research are empirical expressions, obtained from the cutting parameters (tool nose radius, feed rate and depth of cut) and the influence of these parameters on the cutting forces for each carbon steel studied (AISI 1020, AISI 1045 and AISI 4340), as well as a general expression which includes the mechanical properties of these carbon steels. These results enable the user to predict cutting forces when using a turning process.

Wear Characteristic and Life of Al2O3/(W,Ti)C Ceramic Tool in Turning Iron-Based P/M Composites

2010 ◽  
Vol 26-28 ◽  
pp. 1052-1055
Author(s):  
Li Fa Han ◽  
Sheng Guan Qu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Empirical Model ◽  
Feed Rate ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Ceramic Tool ◽  
Iron Based

The wear characteristics and life of Al2O3/(W,Ti)C ceramic tool in turning NbCp-reinforced iron-based P/M composites was investigated. Experimental results indicate that cutting parameters have an influence on tool wear, among which cutting speed and depth of cut seem to be more prominent. The maximum flank wear rapidly increases as the increase in cutting speed and depth of cut. While, it increases gradually as the decrease in feed rate. Meanwhile, an empirical model of tool life is established, from which the influence of cutting speed and depth of cut on tool life is far greater than that of feed rate. Also from the empirical model, the preferable range of cutting parameters was obtained.

Investigation of Cutting Force in High Feed Milling of Ti6Al4V

2013 ◽  
Vol 770 ◽  
pp. 106-109 ◽  
Author(s):  
Jie Xu ◽  
Bin Rong ◽  
Hong Zhou Zhang ◽  
Dong Sheng Wang ◽  
Liang Li
Keyword(s):  
Titanium Alloys ◽  
Cutting Force ◽  
Aerospace Industry ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Increasing Trend ◽  
High Feed ◽  
Series Of Experiments ◽  
Titanium Alloy Ti6al4v

Titanium alloys are widely used in aviation and aerospace industry due to their special mechanical properties. In the process of machining titanium alloys, cutting force is an important physical quantity. In this paper, a series of experiments were carried out to investigate the cutting force in detail during high feed milling of titanium alloy Ti6Al4V with different high feed cutters. Effects of cutting parameters, such as milling speed, feed per tooth, radial cutting depth and axial cutting depth on cutting force were analyzed. The results showed that cutting force presented an obvious increasing trend with the increase of feed per tooth and axial cutting depth. However, the effects of cutting speed and radial cutting depth on cutting force were not obvious.

Sign in / Sign up

Export Citation Format

Share Document