scholarly journals Synthesis of Fe- and Co-Doped TiO2 with Improved Photocatalytic Activity Under Visible Irradiation Toward Carbamazepine Degradation

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3874 ◽  
Author(s):  
Abderrahim El Mragui ◽  
Yuliya Logvina ◽  
Luís Pinto da Silva ◽  
Omar Zegaoui ◽  
Joaquim C.G. Esteves da Silva
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Diffuse Reflectance Spectroscopy ◽  
Anatase Phase ◽  
Aqueous Suspension ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Doped Tio2 ◽  
Doped Titania ◽  
Co Doped

Pure TiO2 and Fe- and Co-doped TiO2 nanoparticles (NPs) as photocatalysts were synthesized using wet chemical methods (sol-gel + precipitation). Their crystalline structure and optical properties were analyzed using X-ray diffraction (XRD), Raman spectroscopy and Fourier-transform infrared (FTIR) spectroscopy, ultraviolet-visible light (UV-Vis) diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The photocatalytic activity of the synthesized nanoparticles was evaluated through degradation of carbamazepine (CBZ) under UV-A and visible-light irradiations. The XRD and Raman analyses revealed that all synthesized nanomaterials showed only the anatase phase. The DRS results showed that the absorption edge was blue-shifted for Fe-doped TiO2 NPs. The decrease in charge recombination was evidenced from the PL investigation for both Co-doped and Fe-doped TiO2 nanomaterials. An enhancement in photocatalytic degradation of carbamazepine in aqueous suspension under both UV-A light and visible-light irradiations was observed for Fe-doped Titania NPs by comparison with pure TiO2. These results suggest that the doping cations could suppress the electron/hole recombination. Therefore, the photocatalytic activity of TiO2-based nanomaterials was enhanced.

scholarly journals Green Synthesis of N/Zr Co-Doped TiO2 for Photocatalytic Degradation of p-Nitrophenol in Wastewater

Catalysts ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 235
Author(s):  
Hayette Benkhennouche-Bouchene ◽  
Julien G. Mahy ◽  
Cédric Wolfs ◽  
Bénédicte Vertruyen ◽  
Dirk Poelman ◽  
...  
Keyword(s):  
Visible Light ◽  
Tio2 Nanoparticles ◽  
Sol Gel ◽  
Visible Region ◽  
Chemical Properties ◽  
Pure Tio2 ◽  
Molar Ratio ◽  
Xps Spectra ◽  
Doped Tio2 ◽  
Co Doped

TiO2 prepared by a green aqueous sol–gel peptization process is co-doped with nitrogen and zirconium to improve and extend its photoactivity to the visible region. Two nitrogen precursors are used: urea and triethylamine; zirconium (IV) tert-butoxide is added as a source of zirconia. The N/Ti molar ratio is fixed regardless of the chosen nitrogen precursor while the quantity of zirconia is set to 0.7, 1.4, 2, or 2.8 mol%. The performance and physico-chemical properties of these materials are compared with the commercial Evonik P25 photocatalyst. For all doped and co-doped samples, TiO2 nanoparticles of 4 to 8 nm of size are formed of anatase-brookite phases, with a specific surface area between 125 and 280 m2 g−1 vs. 50 m2 g−1 for the commercial P25 photocatalyst. X-ray photoelectron (XPS) measurements show that nitrogen is incorporated into the TiO2 materials through Ti-O-N bonds allowing light absorption in the visible region. The XPS spectra of the Zr-(co)doped powders show the presence of TiO2-ZrO2 mixed oxide materials. Under visible light, the best co-doped sample gives a degradation of p-nitrophenol (PNP) equal to 70% instead of 25% with pure TiO2 and 10% with P25 under the same conditions. Similarly, the photocatalytic activity improved under UV/visible reaching 95% with the best sample compared to 50% with pure TiO2. This study suggests that N/Zr co-doped TiO2 nanoparticles can be produced in a safe and energy-efficient way while being markedly more active than state-of-the-art photocatalytic materials under visible light.

Europium Doped Titania Nanocomposites with Enhanced Photocatalytic Activity towards the Degradation of Partially Hydrolysis Polyacrylamide

2011 ◽  
Vol 391-392 ◽  
pp. 219-224
Author(s):  
Jin Huan Li ◽  
Hong Bo Fang ◽  
Wei Wang ◽  
Gui Fan Liu ◽  
Shao Dong Zhang
Keyword(s):  
Photocatalytic Activity ◽  
Oil Recovery ◽  
Inductively Coupled Plasma ◽  
Diffuse Reflectance Spectroscopy ◽  
Uv Light ◽  
Anatase Phase ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Surface Shape ◽  
Titanium Tetraisopropoxide

Nanocrystals with different Eu3+ doping levels (%) were prepared by sol-gel and hydrothermal synthetic method using titanium tetraisopropoxide (TTIP) as titanium source. The products exhibited anatase phase structure, mesoporosity, and interesting surface compositions with three oxygen species and two titanium species. The crystallite sizes, crystal form, surface shape, composition and optical property of catalysts were characterized by X-ray diffraction patterns, UV-Vis diffuse reflectance spectroscopy, XPS and inductively coupled plasma atomic emission spectroscopy. The products were used as the photocatalysts to degrade a partially hydrolysis polyacrylamide (HPAM) under UV-light irradiation, a very useful polymer in oil recovery. For comparison, Degussa P25 and as-prepared pure TiO2 were also tested under the same conditions. The enhanced photocatalytic activity was obtained on as-prepared Eu3+ composites, and the reasons were explained.

Sol-Gel Preparation, Characterization and Photocatalytic Activity of Co Doped Nano-TiO2

2010 ◽  
Vol 177 ◽  
pp. 54-57 ◽  
Author(s):  
Li Na Meng ◽  
Wen Yuan Xu ◽  
Ting Xu
Keyword(s):  
Thin Films ◽  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Sol Gel ◽  
Inhibitory Effect ◽  
Pure Tio2 ◽  
Tio2 Thin Films ◽  
Doped Tio2 ◽  
Co Doping ◽  
Co Doped

Co doped TiO2 nanoparticles and thin films were prepared from Ti(OC4H9)4 by sol-gel method. The influence of Co-doping and its content on the crystallite structure and phase composition of TiO2 was systematically investigated by SEM and XRD, the precursor was analysed by TGA. The photocatalytic activity of nanocomposites was investigated in the photocatalytic degradation of methyl orange. The results indicated that the inhibitory effect of Co-doping on the phase transformation of TiO2 from anatase to rutile receded obviously when the calcination temperature was changed to 650°C from 550°C. Under the ultraviolet light radiation, the favourite Co-doping concentration was 1% and the obtained Co doped TiO2 thin films exhibited higher photocatalytic activity than nanoparticles and pure TiO2 in the photodegradation of methyl orange.

Nonporous Nitrogen and Ruthenium Co-Doped Titania Films for Photocatalysis

2019 ◽  
Vol 18 (03n04) ◽  
pp. 1940043 ◽  
Author(s):  
O. Linnik ◽  
L. Khoroshko
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Structural Properties ◽  
Sol Gel ◽  
High Photocatalytic Activity ◽  
Gel Technique ◽  
Titania Films ◽  
Doped Titania ◽  
Co Doped

Nitrogen and ruthenium co-doped titania films synthesized by sol–gel technique exhibit high photocatalytic activity under both UV and visible light. Incorporation of nitrogen and ruthenium ions in titania lattice is proven by XPS. Both doping agents affected the structural properties of the films.

Effect of Chromium Doping on Visible Light Absorption of Nanosized Titania Sol-Gel

2009 ◽  
Vol 5 ◽  
pp. 95-104 ◽  
Author(s):  
J.A. Pedraza-Avella ◽  
R. López ◽  
F. Martínez-Ortega ◽  
E.A. Páez-Mozo ◽  
Ricardo Gómez
Keyword(s):  
Visible Light ◽  
Light Absorption ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Anatase Phase ◽  
Sol Gel ◽  
Visible Light Absorption ◽  
X Ray ◽  
Chromium Doping ◽  
Doped Titania

Visible light absorption of TiO2 can be induced by the addition of transition metal impurities. However, many dissimilar results have been reported about this subject and there are various interpretations about the origin of these absorption features. In this work, samples of chromium-doped titania (TiO2-Cr) with different dopant contents (0.1, 0.5, 1.0 and 5.0 wt. %) were prepared by a sol-gel method. Their particle size was determined by dynamic light scattering and it was on the nanometer scale (18 nm). X-ray powder diffraction and Raman spectroscopy showed only the presence of anatase phase in all samples. X-ray photoelectron spectroscopy reveals that the oxidation state of chromium in the prepared materials is different than in the dopant precursor. This change can be associated to the oxidative gelling conditions used in the materials preparation. UV VIS diffuse reflectance spectroscopy showed that the chromium doping, until 1.0 wt. %, did not effectively narrow the TiO2 band-gap but it induces the visible light absorption probably through the formation of color centers.

Effect of W doping level on TiO2 on the photocatalytic degradation of Diuron

2016 ◽  
Vol 75 (1) ◽  
pp. 20-27 ◽  
Author(s):  
Ghania Foura ◽  
Ahcène Soualah ◽  
Didier Robert
Keyword(s):  
Visible Light ◽  
Separation Efficiency ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Solar Light ◽  
X Ray Diffraction ◽  
Simulated Solar Light ◽  
Uv Visible ◽  
Doped Titania

In the present study, three compositions of W-doped titania nano-photocatalyst are synthesized via the sol–gel method. The powders obtained were characterized by X-ray diffraction, Raman spectroscopy and UV–visible diffuse reflectance spectroscopy. The photocatalytic performances of the different photocatalysts are tested with respect to the degradation of Diuron in water solutions under simulated solar light and visible light irradiation. The W0.03Ti0.97O2 catalyst exhibits better photoactivity than the pure TiO2 even under simulated solar light and visible light. This improvement in activity was attributed to photoelectron/hole separation efficiency.

Preparation and Photocatalytic Properties of Nanosized La3+ and Co2+ Co-Doped TiO2 by Microemulsions

2007 ◽  
Vol 336-338 ◽  
pp. 1943-1945
Author(s):  
Wei Liang Liu ◽  
Dan Li Lu ◽  
Chang Chun Ge ◽  
Jian Hua Chen ◽  
Zhi Ping He
Keyword(s):  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Visible Light ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Uv Light ◽  
Pure Tio2 ◽  
Doped Tio2 ◽  
Co Doped

La3+ and Co2+ co-doped titania nanoparticles were prepared from reacting TiOSO4, La(NO3)3 and Co(NO3)2 with NH4OH in water/Triton X-100/n-hexanol/cyclohexane microemulsions. The structure, surface morphology and the specific surface area of the samples were characterized. The photocatalytic efficiency of as-prepared TiO2 was tested by photodegrading methyl orange. The results showed that doping with La3+ and Co2+ could suppress the growth of TiO2 grains and increase the specific surface area; When the calcination temperature increased from 300°C to 900°C, the average crystallite size of the particles increased from 7.3nm to 35.6 nm andthe specific surface area of the particles decreased rapidly from 205.5m2/g to 41.2m2/g. The synthesized amorphous particles wer transformed into anatase phase at 300°C, and further into rutile phase at 900°C. UV-Vis diffuse reflectance spectrum revealed that La3+ and Co2+ co-doped TiO2 absorbed UV light and visible light, while pure TiO2 could only absorb UV light. In the experiments of photodegrading methyl orange, it was proved that La3+ and Co2+ co-doped TiO2 had high photocatalytic activity under UV light and visible light, while pure TiO2 showed photocatalytic activity just under UV light.

scholarly journals Enhanced Photocatalytic Activity of CuWO4 Doped TiO2 Photocatalyst Towards Carbamazepine Removal under UV Irradiation

Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Component Part ◽  
Energy Yield ◽  
Mechanical Agitation ◽  
X Ray

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.

Visible-Light-Induced Photocatalytic Activity of Boron-Doped BiVO4

2014 ◽  
Vol 809-810 ◽  
pp. 890-894
Author(s):  
Dan Li ◽  
Lian Wei Shan ◽  
Gui Lin Wang ◽  
Li Min Dong ◽  
Wei Li ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Reflectance Spectroscopy ◽  
Scheelite Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Boron Doped

Boron-BiVO4 samples were synthesized by sol-gel method. They were characterized by UV-vis diffuse reflectance spectroscopy, X-ray diffraction. Photocatalytic activity of the obtained BiVO4 samples was investigated through degrading methylene blue (MB). The results reveal that boron-BiVO4 catalysts have monoclinic scheelite structure. The BiVO4 and Co-BiVO4 photocatalysts were responsive to visible light. Co-BiVO4 photocatalyst showed higher photocatalytic activity than pure BiVO4, resulting in the significantly improved efficiency of degradation of MB.

Sign in / Sign up

Export Citation Format

Share Document