scholarly journals Mechanical Behaviour of Silicone Membranes Saturated with Short Strand, Loose Polyester Fibres for Prosthetic and Rehabilitative Surrogate Skin Applications

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3647 ◽  
Author(s):  
Richard Arm ◽  
Arash Shahidi ◽  
Tilak Dias
Keyword(s):  
Plastic Deformation ◽  
Tensile Strength ◽  
High Strain ◽  
Mechanical Tests ◽  
Fibre Content ◽  
Strain Rates ◽  
Linear Coefficient ◽  
The Aesthetic ◽  
Silicone Membranes ◽  
Hardness Values

Silicone-based elastomers saturated with embedded, short-strand fibres are used for their ability to mimic the aesthetic qualities of skin in clinical and theatrical maxillofacial appliance design. Well-known to prostheses fabricators and technicians, the mechanical impact of fibre addition on elastomeric behaviour endures as tacit, embodied knowledge of the craft, almost unknown in the literature. To examine mechanical changes caused by fibre addition, 100 modified polydimethylsiloxane (PDMS) elastomeric compounds containing incremental amounts of loose polyester fibres were prepared and examined in a variety of mechanical tests. It was found that elasticity and strain percentage at breaking point was reduced by increasing fibre content, but Young’s modulus and ultimate tensile strength (UTS) increased. As fibre content was increased, strain hardening was seen at low strain rates, but exaggerated plastic deformation at high strain rates. PDMS hardness increased by 5 degrees of hardness (Shore-00 scale) for every additional percentage of fibres added and a strong positive linear coefficient (0.993 and 0.995) was identified to reach the hardness values given in the literature for living human skin. The apparent reorienting of loose fibres in the PDMS interrupts and absorbs stress during the loading process similar to the organic response to soft tissue loading, except in extension.

A finite element study on effect of frictional heating in the taylor rod impact problem

2014 ◽  
Vol 11 (6) ◽  
pp. 529-542 ◽  
Author(s):  
Sachin Gautam ◽  
Ravindra Saxena
Keyword(s):  
Plastic Deformation ◽  
Finite Element ◽  
High Strain ◽  
Frictional Heating ◽  
Equivalent Plastic Strain ◽  
Surface Friction ◽  
Effect Of Temperature ◽  
Element Formulation ◽  
Strain Rates ◽  
High Strain Rates

In an impact phenomenon the material is subjected to very short duration high force levels resulting large plastic deformations and rise in temperature at high strain rates. A circular rod impacting against a rigid surface called as Taylor rod impact test is widely used for determining the mechanical behaviour of materials subjected to high strain rates with associated increase in temperature. A three-dimensional large deformation, thermo-elasto-plastic, dynamic, contact, finite element formulation is developed to study the effect of temperature rise due to plastic deformation and surface friction on the deformation and stress fields. It is found that the predicted equivalent plastic strain values are influenced by temperature generated due to plastic deformation and surface friction. The values of the coefficient of friction have a profound effect on the location of fracture initiation on the impacting face in a circular rod.

Comparative Study of the Dynamic Behavior of AA2519 Aluminum Alloy in T6 and T8 Temper Conditions

2019 ◽  
Author(s):  
Adewale Olasumboye ◽  
Gbadebo Owolabi ◽  
Olufemi Koya ◽  
Horace Whitworth ◽  
Nadir Yilmaz
Keyword(s):  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Stress Response ◽  
Flow Stress ◽  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Second Phase ◽  
Strain Rates ◽  
High Strain Rates

Abstract This study investigates the dynamic response of AA2519 aluminum alloy in T6 temper condition during plastic deformation at high strain rates. The aim was to determine how the T6 temper condition affects the flow stress response, strength properties and microstructural morphologies of the alloy when impacted under compression at high strain rates. The specimens (with aspect ratio, L/D = 0.8) of the as-cast alloy used were received in the T8 temper condition and further heat-treated to the T6 temper condition based on the standard ASTM temper designation procedures. Split-Hopkinson pressure bar experiment was used to generate true stress-strain data for the alloy in the range of 1000–3500 /s strain rates while high-speed cameras were used to monitor the test compliance with strain-rate constancy measures. The microstructures of the as received and deformed specimens were assessed and compared for possible disparities in their initial microstructures and post-deformation changes, respectively, using optical microscopy. Results showed no clear evidence of strain-rate dependency in the dynamic yield strength behavior of T6-temper designated alloy while exhibiting a negative trend in its flow stress response. On the contrary, AA2519-T8 showed marginal but positive response in both yield strength and flow behavior for the range of strain rates tested. Post-deformation photomicrographs show clear disparities in the alloys’ initial microstructures in terms of the second-phase particle size differences, population density and, distribution; and in the morphological changes which occurred in the microstructures of the different materials during large plastic deformation. AA2519-T6 showed a higher susceptibility to adiabatic shear localization than AA2519-T8, with deformed and bifurcating transformed band occurring at 3000 /s followed by failure at 3500 /s.

scholarly journals An Image-Based Impact Test for the High Strain Rate Tensile Properties of Brittle Materials

2018 ◽  
Vol 183 ◽  
pp. 02042
Author(s):  
Lloyd Fletcher ◽  
Fabrice Pierron
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
High Strain Rate ◽  
Strain Rate ◽  
Stress Wave ◽  
High Strain ◽  
Brittle Materials ◽  
Test Method ◽  
Strain Rates ◽  
High Strain Rates

Testing ceramics at high strain rates presents many experimental diffsiculties due to the brittle nature of the material being tested. When using a split Hopkinson pressure bar (SHPB) for high strain rate testing, adequate time is required for stress wave effects to dampen out. For brittle materials, with small strains to failure, it is difficult to satisfy this constraint. Because of this limitation, there are minimal data (if any) available on the stiffness and tensile strength of ceramics at high strain rates. Recently, a new image-based inertial impact (IBII) test method has shown promise for analysing the high strain rate behaviour of brittle materials. This test method uses a reflected compressive stress wave to generate tensile stress and failure in an impacted specimen. Throughout the propagation of the stress wave, full-field displacement measurements are taken, from which strain and acceleration fields are derived. The acceleration fields are then used to reconstruct stress information and identify the material properties. The aim of this study is to apply the IBII test methodology to analyse the stiffness and strength of ceramics at high strain rates. The results show that it is possible to identify the elastic modulus and tensile strength of tungsten carbide at strain rates on the order of 1000 s-1. For a tungsten carbide with 13% cobalt binder the elastic modulus was identified as 516 GPa and the strength was 1400 MPa. Future applications concern boron carbide and sapphire, for which limited data exist in high rate tension.

scholarly journals Effect of Fiber Blending Ratio on the Tensile Properties of Steel Fiber Hybrid Reinforced Cementitious Composites under Different Strain Rates

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4504
Author(s):  
Minjae Son ◽  
Gyuyong Kim ◽  
Hongseop Kim ◽  
Sangkyu Lee ◽  
Yaechan Lee ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Synergistic Effect ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Performance ◽  
Steel Fiber ◽  
High Strain ◽  
Strain Rates ◽  
Cementitious Composite ◽  
Hybrid Fiber

In this study, a high-performance hybrid fiber-reinforced cementitious composite (HP-HFRCC) was prepared, by mixing hooked steel fiber (HSF) and smooth steel fiber (SSF) at different blending ratios, to evaluate the synergistic effect of the blending ratio between HSF and SSF and the strain rate on the tensile properties of HP-HFRCC. The experimental results showed that the micro- and macrocrack control capacities of HP-HFRCC varied depending on the blending ratio and strain rate, and the requirement for deriving the appropriate blending ratio was confirmed. Among the HP-HFRCC specimens, the specimen mixed with HSF 1.0 vol.% and SSF 1.0 vol.% (H1.0S1.0) exhibited a significant increase in the synergistic effect on the tensile properties at the high strain rate, as SSF controlled the microcracks and HSF controlled the macrocracks. Consequently, it exhibited the highest strain rate sensitivities of tensile strength, strain capacity, and peak toughness among the specimens evaluated in this study.

Mechanical properties of mother of pearl in tension

1977 ◽  
Vol 196 (1125) ◽  
pp. 443-463 ◽  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Mechanical Behaviour ◽  
Mechanical Tests ◽  
Protein Matrix ◽  
Submicroscopic Structure ◽  
Measured Strain ◽  
Work Of Fracture ◽  
Extensive Plastic Deformation

Mother of pearl, or nacre, is one of a number of characteristic skeletal structures of molluscs, occurring in cephalopods, gastropods and bivalves. It consists of plates of aragonite, about 0.3 μm thick, arranged in sheets, with a tenuous protein matrix. Mechanical tests of nacre from all three classes show that it has a tensile strength of between 35 and 110 MN m -2 . It is slightly viscoelastic, and shows marked, though not extensive, plastic deformation. The maximum measured strain was 0.018. While under­going plastic deformation the material shows considerable optical changes. The regions where plastic flow is occurring show ‘tension lines’, probably equivalent to similar lines in bone. These are probably caused by voids forming in the protein matrix. The work of fracture is very different in different loading directions, being about 1.65 x 10 3 J m -2 when fractured across the grain, and 1.5 x 10 2 J m -2 when fractured along it. Nacre shows considerable ability to stop cracks. An attempt is made to explain qualitatively the mechanical behaviour of nacre in terms of its submicroscopic structure. It is concluded that the precise geometric arrangement of the plates is most important, and that this constraint may make nacre less suitable for shells that must be built quickly.

Rate Dependent Deformation of Semi-Crystalline Polypropylene Near Room Temperature

1997 ◽  
Vol 119 (3) ◽  
pp. 216-222 ◽  
Author(s):  
E. M. Arruda ◽  
S. Ahzi ◽  
Y. Li ◽  
A. Ganesan
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Room Temperature ◽  
Strain Softening ◽  
High Strain ◽  
Constant Strain Rate ◽  
Strain Rates ◽  
High Strain Rates ◽  
Rate Dependent ◽  
Static Conditions

We examine the strain rate dependent, large plastic deformation in isotropic semi-crystalline polypropylene at room temperature. Constant strain rate uniaxial compression tests on cylindrical polypropylene specimens show very little true strain softening under quasi-static conditions. At high strain rates very large amounts (38 percent) of apparent strain softening accompanied by temperature rises are recorded. We examine the capability of a recently proposed constitutive model of plastic deformation in semi-crystalline polymers to predict this behavior. We neglect the contribution of the amorphous phase to the plastic deformation response and include the effects of adiabatic heating at high strain rates. Attention is focused on the ability to predict rate dependent yielding, strain softening, strain hardening, and adiabatic temperature rises with this approach. Comparison of simulations and experimental results show good agreement and provide insight into the merits of using a polycrystalline modeling assumption versus incorporating the amorphous contribution. Discrepancies between experiments and model predictions are explained in terms of expectations associated with neglecting the amorphous deformation.

Sign in / Sign up

Export Citation Format

Share Document