scholarly journals Catalytic Soot Oxidation Activity of NiO–CeO2 Catalysts Prepared by a Coprecipitation Method: Influence of the Preparation pH on the Catalytic Performance

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3436 ◽  
Author(s):  
Amar Bendieb Aberkane ◽  
María Pilar Yeste ◽  
Djazi Fayçal ◽  
Daniel Goma ◽  
Miguel Ángel Cauqui
Keyword(s):  
Electron Microscopy ◽  
Surface Area ◽  
Mixed Oxide ◽  
Soot Oxidation ◽  
Catalytic Performance ◽  
Coprecipitation Method ◽  
Bet Surface Area ◽  
Mixed Oxide Catalysts ◽  
Ph Values ◽  
Tight Contact

A series of NiO–CeO2 mixed oxide catalysts have been synthesized by a modified coprecipitation method at three different pH values (pH = 8, 9, and 10). The NiO–CeO2 mixed oxide samples were characterized by TGA, XRD, inductively coupled plasma atomic emission spectroscopy (ICP-AES), FTIR, Brunauer–Emmett–Teller (BET) surface area, H2 temperature-programmed reduction (H2-TPR), and electron microscopy (high-angle annular dark-field transmission electron microscopy/energy-dispersive X-ray spectroscopy (HAADF-TEM/EDS)). The catalytic activities of the samples for soot oxidation were investigated under loose and tight contact conditions. The catalysts exhibited a high BET surface area with average crystal sizes that varied with the pH values. Electron microscopy results showed the formation of small crystallites (~5 nm) of CeO2 supported on large plate-shaped particles of NiO (~20 nm thick). XRD showed that a proportion of the Ni2+ was incorporated into the ceria network, and it appeared that the amount on Ni2+ that replaced Ce4+ was higher when the synthesis of the mixed oxides was carried out at a lower pH. Among the synthesized catalysts, Ni-Ce-8 (pH = 8) exhibited the best catalytic performance.

scholarly journals Magnetically Recyclable Wool Keratin Modified Magnetite Powders for Efficient Removal of Cu2+ Ions from Aqueous Solutions

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1068
Author(s):  
Xinyue Zhang ◽  
Yani Guo ◽  
Wenjun Li ◽  
Jinyuan Zhang ◽  
Hailiang Wu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Ion Concentration ◽  
Bet Surface Area ◽  
Chemical Compositions ◽  
Ion Adsorption ◽  
X Ray ◽  
Wool Keratin

The treatment of wastewater containing heavy metals and the utilization of wool waste are very important for the sustainable development of textile mills. In this study, the wool keratin modified magnetite (Fe3O4) powders were fabricated by using wool waste via a co-precipitation technique for removal of Cu2+ ions from aqueous solutions. The morphology, chemical compositions, crystal structure, microstructure, magnetism properties, organic content, and specific surface area of as-fabricated powders were systematically characterized by various techniques including field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), thermogravimetric (TG) analysis, and Brunauer–Emmett–Teller (BET) surface area analyzer. The effects of experimental parameters such as the volume of wool keratin hydrolysate, the dosage of powder, the initial Cu2+ ion concentration, and the pH value of solution on the adsorption capacity of Cu2+ ions by the powders were examined. The experimental results indicated that the Cu2+ ion adsorption performance of the wool keratin modified Fe3O4 powders exhibited much better than that of the chitosan modified ones with a maximum Cu2+ adsorption capacity of 27.4 mg/g under favorable conditions (0.05 g powders; 50 mL of 40 mg/L CuSO4; pH 5; temperature 293 K). The high adsorption capacity towards Cu2+ ions on the wool keratin modified Fe3O4 powders was primarily because of the strong surface complexation of –COOH and –NH2 functional groups of wool keratins with Cu2+ ions. The Cu2+ ion adsorption process on the wool keratin modified Fe3O4 powders followed the Temkin adsorption isotherm model and the intraparticle diffusion and pseudo-second-order adsorption kinetic models. After Cu2+ ion removal, the wool keratin modified Fe3O4 powders were easily separated using a magnet from aqueous solution and efficiently regenerated using 0.5 M ethylene diamine tetraacetic acid (EDTA)-H2SO4 eluting. The wool keratin modified Fe3O4 powders possessed good regenerative performance after five cycles. This study provided a feasible way to utilize waste wool textiles for preparing magnetic biomass-based adsorbents for the removal of heavy metal ions from aqueous solutions.

scholarly journals Statistically Guided Synthesis of MoV-Based Mixed-Oxide Catalysts for Ethane Partial Oxidation

Catalysts ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 370
Author(s):  
Juan Jimenez ◽  
Kathleen Mingle ◽  
Teeraya Bureerug ◽  
Cun Wen ◽  
Jochen Lauterbach
Keyword(s):  
Acetic Acid ◽  
Partial Oxidation ◽  
Mixed Oxide ◽  
Structural Integrity ◽  
Product Distribution ◽  
Catalytic Performance ◽  
Oxide Catalysts ◽  
Acid Yield ◽  
Mixed Oxide Catalysts ◽  
Catalyst Composition

The catalytic performance of Mo8V2Nb1-based mixed-oxide catalysts for ethane partial oxidation is highly sensitive to the doping of elements with redox and acid functionality. Specifically, control over product distributions to ethylene and acetic acid can be afforded via the specific pairing of redox elements (Pd, Ni, Ti) and acid elements (K, Cs, Te) and the levels at which these elements are doped. The redox element, acid element, redox/acid ratio, and dopant/host ratio were investigated using a three-level, four-factor factorial screening design to establish relationships between catalyst composition, structure, and product distribution for ethane partial oxidation. Results show that the balance between redox and acid functionality and overall dopant level is important for maximizing the formation of each product while maintaining the structural integrity of the host metal oxide. Overall, ethylene yield was maximized for a Mo8V2Nb1Ni0.0025Te0.5 composition, while acetic acid yield was maximized for a Mo8V2Nb1Ti0.005Te1 catalyst.

scholarly journals Pt-Promoted Tungsten Carbide Nanostructures on Mesoporous Pinewood-Derived Activated Carbon for Catalytic Oxidation of Formaldehyde at Low Temperatures

2020 ◽  
Vol 1 (2) ◽  
pp. 86-105
Author(s):  
Qiangu Yan ◽  
Zhiyong Cai
Keyword(s):  
Electron Microscopy ◽  
Activated Carbon ◽  
Relative Humidity ◽  
Tungsten Carbide ◽  
Catalytic Oxidation ◽  
Space Velocity ◽  
Catalytic Performance ◽  
Inert Atmosphere ◽  
Bet Surface Area ◽  
Formaldehyde Concentration

Tungsten carbide (WC) nanostructures were prepared by carbothermal reduction (CR) of tungsten-impregnated pinewood-derived activated carbon (AC) at 1000 °C under an inert atmosphere. Brunauer-Emmet-Teller (BET) surface area, pore structures of the AC, and catalyst samples were evaluated by N2 adsorption-desorption experiments. The structures of the catalysts were characterized using X-ray powder diffraction (XRD). The morphologies and particle structures of the synthesized WC nanoparticles were investigated by field emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM). The WC/AC material was used as support of the platinum catalysts for catalytic oxidation of formaldehyde (HCHO) from interior sources. Pt-WC/AC catalysts with different platinum loadings were assessed for the catalytic oxidation of HCHO at low temperature. The catalytic performance was found to be significantly influenced by reaction temperature, initial formaldehyde concentration, relative humidity, and space velocity. The testing results demonstrated that HCHO can be totally oxidized by the 1 wt% Pt-WC/AC catalyst in the gas hourly space velocity (GHSV) = 50,000 h−1 at 30 °C with a relative humidity (RH) of 40%.

scholarly journals The Photocatalytic and Antibacterial Performance of Nitrogen-Doped TiO2: Surface-Structure Dependence and Silver-Deposition Effect

Nanomaterials ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 2261 ◽  
Author(s):  
Abdul Wafi ◽  
Erzsébet Szabó-Bárdos ◽  
Ottó Horváth ◽  
Mihály Pósfai ◽  
Éva Makó ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Surface Area ◽  
Photocatalytic Performance ◽  
Visible Region ◽  
Bet Surface Area ◽  
Doped Tio2 ◽  
X Ray ◽  
Nitrogen Doped ◽  
Visible Light Driven

Catalysts for visible-light-driven oxidative cleaning processes and antibacterial applications (also in the dark) were developed. In order to extend the photoactivity of titanium dioxide into the visible region, nitrogen-doped TiO2 catalysts with hollow and non-hollow structures were synthesized by co-precipitation (NT-A) and sol–gel (NT-U) methods, respectively. To increase their photocatalytic and antibacterial efficiencies, various amounts of silver were successfully loaded on the surfaces of these catalysts by using a facile photo-deposition technique. Their physical and chemical properties were evaluated by using scanning electron microscopy (SEM), transmission electron microscopy–energy dispersive X-ray spectroscopy (TEM–EDS), Brunauer–Emmett–Teller (BET) surface area, X-ray diffraction (XRD), and diffuse reflectance spectra (DRS). The photocatalytic performances of the synthesized catalysts were examined in coumarin and 1,4-hydroquinone solutions. The results showed that the hollow structure of NT-A played an important role in obtaining high specific surface area and appreciable photoactivity. In addition, Ag-loading on the surface of non-hollow structured NT-U could double the photocatalytic performance with an optimum Ag concentration of 10−6 mol g−1, while a slight but monotonous decrease was caused in this respect for the hollow surface of NTA upon increasing Ag concentration. Comparing the catalysts with different structures regarding the photocatalytic performance, silverized non-hollow NT-U proved competitive with the hollow NT-A catalyst without Ag-loading for efficient visible-light-driven photocatalytic oxidative degradations. The former one, due to the silver nanoparticles on the catalyst surface, displayed an appreciable antibacterial activity, which was comparable to that of a reference material practically applied for disinfection in polymer coatings.

scholarly journals Highly Active Transition Metal-Promoted CuCeMgAlO Mixed Oxide Catalysts Obtained from Multicationic LDH Precursors for the Total Oxidation of Methane

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 613
Author(s):  
Hussein Mahdi S. Al-Aani ◽  
Mihaela M. Trandafir ◽  
Ioana Fechete ◽  
Lucia N. Leonat ◽  
Mihaela Badea ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transition Metal ◽  
Mixed Oxide ◽  
Mixed Oxides ◽  
Catalytic Performance ◽  
Atomic Ratio ◽  
Total Oxidation ◽  
X Ray ◽  
Oxidation Of Methane ◽  
Al2o3 Catalyst

To improve the catalytic performance of an active layered double hydroxide (LDH)-derived CuCeMgAlO mixed oxide catalyst in the total oxidation of methane, it was promoted with different transition-metal cations. Thus, two series of multicationic mixed oxides were prepared by the thermal decomposition at 750 °C of their corresponding LDH precursors synthesized by coprecipitation at constant pH of 10 under ambient atmosphere. The first series of catalysts consisted of four M(3)CuCeMgAlO mixed oxides containing 3 at.% M (M = Mn, Fe, Co, Ni), 15 at.% Cu, 10 at.% Ce (at.% with respect to cations), and with Mg/Al atomic ratio fixed to 3. The second series consisted of four Co(x)CuCeMgAlO mixed oxides with x = 1, 3, 6, and 9 at.% Co, while keeping constant the Cu and Ce contents and the Mg/Al atomic ratio. All the mixed oxides were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) coupled with X-ray energy dispersion analysis (EDX), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption at −196 °C, temperature-programmed reduction under hydrogen (H2-TPR), and diffuse reflectance UV-VIS spectroscopy (DR UV-VIS), while thermogravimetric and differential thermal analyses (TG-DTG-DTA) together with XRD were used for the LDH precursors. The catalysts were evaluated in the total oxidation of methane, a test reaction for volatile organic compounds (VOC) abatement. Their catalytic performance was explained in correlation with their physicochemical properties and was compared with that of a reference Pd/Al2O3 catalyst. Among the mixed oxides studied, Co(3)CuCeMgAlO was found to be the most active catalyst, with a temperature corresponding to 50% methane conversion (T50) of 438 °C, which was only 19 °C higher than that of a reference Pd/Al2O3 catalyst. On the other hand, this T50 value was ca. 25 °C lower than that observed for the unpromoted CuCeMgAlO system, accounting for the improved performance of the Co-promoted catalyst, which also showed a good stability on stream.

Synthesis of Carbon Nanofiber-Titania-Cordierite Monolith Composite and its Application as Catalyst Support on Citral Hydrogenation

2012 ◽  
Vol 535-537 ◽  
pp. 178-185 ◽  
Author(s):  
Jie Zhu ◽  
Ming Shi Li ◽  
Mo Hong Lu
Keyword(s):  
Surface Area ◽  
Carbon Nanofiber ◽  
Sol Gel ◽  
Catalyst Support ◽  
Textural Properties ◽  
Mesoporous Structure ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
Tetrabutyl Titanate ◽  
Citral Hydrogenation

We reported the synthesis of a promising carbon nanofiber-titania-cordierite monolith composite (C/TiO2/monolith) and its application in citral hydrogenation. The composite was synthesized through two steps: TiO2 coating on the surface of the monolith with sol-gel method and the following carbon deposit by methane decomposition. C/TiO2/monolith was subsequently employed to prepare its supported palladium catalyst, Pd/C/TiO2/monolith and its catalytic performance was evaluated in selective hydrogenation of citral. Results revealed that 2.0 wt% tetrabutyl titanate sol in composite synthesis was the best in improving textural properties of C/TiO2/monolith. The optimal composite possessed a BET surface area of 39.4 m2/g and micropore area accounted for only 3.8% of its total BET surface area. It contained about 30 wt% of carbon, which was mainly composed of carbon nanofiber. Pd/C/TiO2/monolith exhibited the high citronellal selectivity (81%) at 90% citral conversion, which was attributed to the decrease of internal diffusion limitation due to its mesoporous structure.

scholarly journals Synthesis and Characterisation of Mesoporous TiO2 Nanoparticles by Novel Surfactant Assisted Sol-gel Method for the Degradation of Organic Compounds

2018 ◽  
Vol 63 (1) ◽  
pp. 85-95 ◽  
Author(s):  
Harish Phattepur ◽  
Gowrishankar Bychapur Siddaiah ◽  
Nagaraju Ganganagappa
Keyword(s):  
Electron Microscopy ◽  
Tio2 Nanoparticles ◽  
Surface Area ◽  
Sol Gel ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Tio2 Nps ◽  
Gel Method ◽  
X Ray ◽  
Surfactant Assisted

A sol-gel method was employed to synthesise pure titanium dioxide (TiO2) and surfactant assisted TiO2 nanoparticles (NPs). The effect of novel surfactant viz., Lauryl lactyl lactate on photocatalytic properties of TiO2 was studied. TiO2 NPs were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), UV-Vis Diffuse Reflectance spectra (DRS), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermo gravimetric analysis (TGA), and Brunauer – Emmet - Teller (BET) surface area. Anatase phase of TiO2 was confirmed by X-Ray diffraction pattern and the crystallite size was between 9–19 nm. Addition of surfactant improved the BET surface area, surface defects, while the agglomeration of particles was reduced. DRS results revealed that the addition of surfactant to TiO2 sol induced a red shift of the absorption edge which resulted in the reduction of band gap from 3.23 to 3.21 eV. These physicochemical properties of TiO2 NPs were correlated with photocatalytic degradation of phenol. About 92% of phenol degradation was observed for surfactant assisted TiO2 NPs (SA-TiO2). Salicylic acid and caffeine were also degraded using SA-TiO2 NPs.

Methanol Conversion to Propylene over Mo-HZSM-5 Zeolite

2013 ◽  
Vol 834-836 ◽  
pp. 476-480
Author(s):  
Hai Rong Zhang ◽  
Hong Yan Liu ◽  
Yu Jiang ◽  
Xiao Hua Chang ◽  
Kai Yuan ◽  
...  
Keyword(s):  
Hydrothermal Method ◽  
Surface Area ◽  
Fixed Bed ◽  
Nitrogen Adsorption ◽  
Methanol Conversion ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
Al Content ◽  
Strong Acidity

A series of Mo-ZSM-5 zeolites have been synthesized by in site hydrothermal method and their catalytic performance for methanol conversion to propylene was tested in a fixed bed reaction at WHSV=4 h-1, pressure of 1 atm, and MeOH/H2O (mol) ratio of 1. The effect of Mo and Al content on the structure and acidity of Mo-ZSM-5 zeolites were characterized by nitrogen adsorption and NH3-TPD. The results showed that Mo incorporation gradually decreased the BET surface area and weaken the strong acidity on the surface of the zeolites. At 470 °C, the maximum selectivity of propylene and the P/E (Propylene to Ethane) ratio were achieved 45.04 % and 7.30, which were higher than those over Mo free HZSM-5 by 4.12% and 3.47, respectively. Mo-ZSM-5 zeolites are promising catalysts for methanol conversion to propylene with a high P/E.

Kinetic and structural constraints during glauconite dissolution: implications for mineral disposal of CO2

2008 ◽  
Vol 72 (1) ◽  
pp. 27-31 ◽  
Author(s):  
S. Fernandez-Bastero ◽  
C. Gil-Lozano ◽  
M. J. I. Briones ◽  
L. Gago-Duport
Keyword(s):  
Electron Microscopy ◽  
Batch Reactor ◽  
Bet Surface Area ◽  
Dissolution Mechanism ◽  
Structural Constraints ◽  
X Ray Diffraction ◽  
Ph Values ◽  
Transmission Electron ◽  
Ph Range

AbstractThe kinetics of glauconite dissolution have been determined in the pH range 2—10 (T = 25°C) using flow-batch reactor experiments. Besides the kinetic characteristics, the structural and textural aspects which could influence its long-term reactivity have also been characterized by means of X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM) and BET surface area measurements. The results from these analyses showed that glauconite follows a dual dissolution pathway which is pH-dependent, being more stable at neutral or slightly alkaline pH values. Under acidic conditions, glauconite is slightly more soluble than other ubiquitous silicates present in the marine sediments. The dissolution mechanism is incongruent at very acid pH values and tends to be congruent for intermediate and neutral ones. In addition, the results from the structural analyses suggest that the dissolution is a two-step process: the first one involves the disorder of the octahedral and tetrahedral layers, probably following a turbostratic mechanism which is evident in the XRD spectra as selective broadening of several reflections. In the second step, the dissolution of the cations from interlayer positions takes place and leads to the formation of an amorphous residue which acts as a passivating layer and reduces the reactive surface considerably. The influence of these aspects on CO2 capture via carbonation reactions is discussed.

Sign in / Sign up

Export Citation Format

Share Document