scholarly journals Experimental Study on the Shrinkage Behavior and Mechanical Properties of AAM Mortar Mixed with CSA Expansive Additive

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3312 ◽  
Author(s):  
Sung Choi ◽  
Gum-Sung Ryu ◽  
Kyeong-Taek Koh ◽  
Gi-Hong An ◽  
Hyeong-Yeol Kim
Keyword(s):  
Modulus Of Elasticity ◽  
Compensation Effect ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Shrinkage Stress ◽  
Calcium Sulfoaluminate ◽  
Total Shrinkage ◽  
Expansive Additive ◽  
Shrinkage Compensation

In this study, a calcium sulfoaluminate-based expansive additive (0%, 2.5%, 5.0%, and 7.5% by the mass of the binder) was added to compensate for the shrinkage of alkali-activated material (AAM) mortar. Modulus of elasticity curves based on the ACI 209 model were derived for the AAM mortar mixed with the additive by measuring the compressive strength and modulus of elasticity. Moreover, autogenous shrinkage and total shrinkage were measured for 150 days, and drying shrinkage was calculated by excluding autogenous shrinkage from total shrinkage. For the autogenous and drying shrinkage of AAM mortar, shrinkage curves by age were obtained by deriving material constants using the exponential function model. Finally, shrinkage stress was calculated using the modulus of elasticity of the AAM mortar and the curves obtained using the shrinkage model. The results showed that the calcium sulfoaluminate-based expansive additive had an excellent compensation effect on the drying shrinkage of AAM mortar, but the effect was observed only at early ages when the modulus of elasticity was low. From a long-term perspective, the shrinkage compensation effect was low when the modulus of elasticity was high, and thus, shrinkage stress could not be reduced.

Development of shrinkage resistant microfibre-reinforced cement-based composites

2012 ◽  
Vol 2 (2) ◽  
Author(s):  
P. Hamedanimojarrad ◽  
G. Adam ◽  
A. Ray ◽  
P. Thomas ◽  
K. Vessalas
Keyword(s):  
Drying Shrinkage ◽  
Shrinkage Strain ◽  
Crack Size ◽  
Moisture Loss ◽  
The Novel ◽  
Total Shrinkage ◽  
Low Concentrations ◽  
Reinforced Cement ◽  
Short And Long Term

AbstractDifferent shrinkage types may cause serious durability dilemma on restrained concrete parts due to crack formation and propagation. Several classes of fibres are used by concrete industry in order to reduce crack size and crack number. In previous studies, most of these fibre types were found to be effective in reducing the number and sizes of the cracks, but not in shrinkage strain reduction. This study deals with the influence of a newly introduced type of polyethylene fibre on drying shrinkage reduction. The novel fibre is a polyethylene microfibre in a new geometry, which is proved to reduce the amount of total shrinkage in mortars. This special hydrophobic polyethylene microfibre also reduces moisture loss of mortar samples. The experimental results on short and long-term drying shrinkage as well as on several other properties are reported. The hydrophobic polyethylene microfibre showed promising improvement in shrinkage reduction even at very low concentrations (0.1% of cement weight).

Effect of Steel Slag on Shrinkage Characteristics of Calcium Sulfoaluminate Cement

2021 ◽  
Vol 1036 ◽  
pp. 263-276
Author(s):  
Hao Ran Huang ◽  
Yi Shun Liao ◽  
Siraj Ai Qunaynah ◽  
Guo Xi Jiang ◽  
Da Wei Guo ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Relative Humidity ◽  
Cement Paste ◽  
Steel Slag ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Chemical Shrinkage ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Slag Content

The effects of steel slag with 0, 10%, 20 % and 40% content on the chemical shrinkage, autogenous shrinkage, internal relative humidity, and drying shrinkage of calcium sulfoaluminate cement paste were studied. The results show that the compressive strength of calcium sulfoaluminate cement paste at an early stage decreases gradually when the content of steel slag increases. When the steel slag content is 0 and 10%, the compressive strength of hardened cement pastes gradually decreases at 90 and 180 days, but the samples with steel slag content of 20% and 40% maintain the compressive strength growth within 180 d. With the extension of curing period, the gap of compressive strength is gradually narrowed. The autogenous shrinkage decreases with the increase of steel slag content and has a good linear relationship with the relative humidity inside the paste. The proportion of autogenous shrinkage to chemical shrinkage is deficient, and most chemical shrinkage occurs in the form of the pore volume. Although the trends of drying shrinkage and autogenous are consistent, the former is more severe than the latter.

Study on Utilization of Silica-Calcium Tailings in Concrete

2014 ◽  
Vol 599 ◽  
pp. 93-97
Author(s):  
Xiao Wu Tian ◽  
Wei Guo Shen ◽  
Lai Shan ◽  
Liang Hong Cao ◽  
Qing Lan ◽  
...  
Keyword(s):  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Particle Morphology ◽  
Cementitious Materials ◽  
Early Age ◽  
Fine Aggregate ◽  
Safety Hazard ◽  
Total Shrinkage ◽  
Potential Safety ◽  
Large Production

The large production of tailings has caused soil, water and air pollution and serious potential safety hazard. The composition, particle morphology, particle size distribution of the silica-calcium tailings are investigated to assess the feasibility of using it in concrete in this paper. The silica-calcium tailings are mainly composed of quartz, calcite and dolomite. The results show that the tailings powder can stimulate the hydration of cement and fill the gradation gap between fine aggregate and cementitious materials in concrete as micronized sand to meet the requirements of concrete. The incorporation of silica-calcium tailings in concrete reduces the ultimate total shrinkage, autogenous shrinkage and drying shrinkage at early age.

scholarly journals Volume Deformation of Steam-Cured Concrete with Slag during and after Steam Curing

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1647
Author(s):  
Xiaofeng Han ◽  
Hua Fu ◽  
Gege Li ◽  
Li Tian ◽  
Chonggen Pan ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Integrated Model ◽  
Hydration Reaction ◽  
Curing Process ◽  
Hydration Degree ◽  
Steam Curing ◽  
Volume Deformation ◽  
Total Shrinkage

In order to better predict the development of shrinkage deformation of steam-cured concrete mixed with slag, a deformation-temperature-humidity integrated model test, a hydration heat test, and an elastic modulus test were performed. The effects of the steam-curing process and the content of slag on shrinkage deformation, hydration degree and elastic modulus of concrete were studied. The results indicate that during the steam-curing process, the concrete has an “expansion-shrinkage” pattern. After the steam curing, the deformation of concrete is dominated by drying shrinkage. After the addition of slag, the shrinkage deformation of steam-cured concrete is increased. The autogenous shrinkage increases by 0.5–12%, and the total shrinkage increases by 1.5–8% at 60 days. At the same time, slag reduces the hydration degree of steam-cured concrete and modulus of elasticity. A prediction model for the hydration degree of steam-cured concrete is established, which can be used to calculate the degree of hydration at any curing age. Based on the capillary tension generated by the capillary pores in concrete, an integrated model of autogenous shrinkage and total shrinkage is established with the relative humidity directly related to the water loss in the concrete as the driving parameter. Whether the shrinkage deformation is caused by hydration reaction or the external environment, this model can better predict the shrinkage deformation of steam-cured concrete.

scholarly journals Case Study on Early Age Shrinkage of Cement-based Composites

2015 ◽  
Vol 2 ◽  
pp. 79
Author(s):  
Andina Sprince ◽  
Leonids Pakrastinsh
Keyword(s):  
High Performance ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Cement Composite ◽  
Early Age ◽  
Thin Walls ◽  
Reinforced Cement ◽  
Pva Fiber

The aim of this paper was to study the behaviour of new high-performance fibre-reinforced cement composite materials (FRCC) that are reinforced with polyvinyl alcohol (PVA) fibres. The shrinkage deformations at early age, the compressive strength and modulus of elasticity of the new compositions had been determined. Test results shows that the addition of PVA fiber 1.10% and 0.55% by weight of the cement has negligible influence on concrete drying shrinkage, however, it is affect the concrete plastic and autogenous shrinkage. The results of the experiments permitted the prediction of long-term deformations of the concrete. Wider use of this material permit the construction of sustainable next generation structures with thin walls and large spans that cannot be built using the traditional concrete.

The Influence of Chemical Admixtures on the Autogenous Shrinkage Ultra-High Performance Concrete

2010 ◽  
Vol 452-453 ◽  
pp. 725-728 ◽  
Author(s):  
Jung Jun Park ◽  
Sung Wook Kim ◽  
Gum Sung Ryu ◽  
Kwang Myung Lee
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Pulse Velocity ◽  
Reducing Agent ◽  
Shrinkage Stress ◽  
Early Age ◽  
Ultra High Performance Concrete ◽  
Expansive Additive ◽  
Shrinkage Reducing Agent

Ultra-high performance concrete (UHPC) is a material developing remarkable performance with compressive strength of about 200 MPa and flexural strength of approximately 30 MPa on which research is actively conducted today. However, UHPC is also characterized by a mixing composed of a high specific quantity of binder that is a W/B ratio of about 0.2, which requires to examine the effects of the autogenous shrinkage. Accordingly, this study investigates the effects of the use of expansive additive and water reducing agent on the autogenous shrinkage of UHPC at early age. To that goal, autogenous shrinkage test and ultrasonic pulse velocity (UPV) monitoring are conducted for a mixing of UHPC using expansive additive and shrinkage reducing agent. The experimental results reveal that the autogenous shrinkage of UHPC reduces by 24% for a mix of UHPC adopting both 7.5% of expansive additive and 1% of shrinkage reducing agent compared to the mix without admixture. Furthermore, this mix is seen to compensate the autogenous shrinkage occurring at early age when UHPC develops its largest stiffness in view of the UPV evolution curve. At that time, the shrinkage stress seems to be extremely softened.

scholarly journals Autogenous and drying shrinkage of mortars based on Portland and calcium sulfoaluminate cements

2020 ◽  
Vol 53 (5) ◽  
Author(s):  
Davide Sirtoli ◽  
Mateusz Wyrzykowski ◽  
Paolo Riva ◽  
Pietro Lura
Keyword(s):  
Portland Cement ◽  
Water Demand ◽  
Ordinary Portland Cement ◽  
Rapid Evolution ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
High Water ◽  
Early Age ◽  
Volume Changes ◽  
Calcium Sulfoaluminate

Abstract Calcium sulfoaluminate (CSA) cement can be used as an alternative binder in concrete, partially or fully replacing ordinary Portland cement. While CSA cement considerably accelerates the mechanical properties development, the rapid evolution of the microstructure together with the high water demand cause rapid and large volume changes at early ages. As volume changes may lead to early-age cracking, measures to reduce them may be required In this paper, autogenous and drying shrinkage are studied in mortars prepared with Portland cement, CSA cement or a 50/50 blend as binder. Very fast self-desiccation and high autogenous shrinkage of the CSA-based mortar were observed compared to the mortar made with Portland cement. On the other hand, the early-age volume changes can be limited if a blend of the two cements is used. The blended system revealed a bi-modal trend in the evolution of self-desiccation and autogenous shrinkage, in which the initial fast self-desiccation and shrinkage enter the dormant phase after the first couple of days and again start after about 28 days.

scholarly journals Evaluation of the Thermal and Shrinkage Stresses in Restrained High-Performance Concrete

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3680 ◽  
Author(s):  
Yang Yang ◽  
Linhao Ma ◽  
Jie Huang ◽  
Chunping Gu ◽  
Zhenjian Xu ◽  
...  
Keyword(s):  
Thermal Stress ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Shrinkage Stress ◽  
Early Age ◽  
Volume Deformation ◽  
Curing Conditions ◽  
Drying Shrinkage Stress

The early age volume deformation is the main course for the cracking of high-performance concrete (HPC). Hence, the shrinkage behavior and the restrained stress development of HPC under different restraints and curing conditions were experimentally studied in this paper. The method to separate the stress components in the total restraint stress was proposed. The total restrained stress was separated into autogenous shrinkage stress, drying shrinkage stress and thermal stress. The results showed that the developments of the free shrinkage (autogenous shrinkage and drying shrinkage) and the restrained stress were accelerated when the drying began; but the age when the drying began did not significantly influence the long-term shrinkage and restrained stress of HPC; the autogenous shrinkage stress continuously contributed to the development of the total restrained stress in HPC; the drying shrinkage stress developed very rapidly soon after the drying began; and the thermal stress was generated when the temperature dropped. The thermal stress was predominant at the early age, but the contributions of the three stresses to the total restrained stress were almost the same at the age of 56 d in this study.

scholarly journals Incorporation of Natural Fibres in Rendering Mortars for the Durability of Walls

2021 ◽  
Vol 6 (6) ◽  
pp. 82
Author(s):  
Cinthia Maia Pederneiras ◽  
Rosário Veiga ◽  
Jorge de Brito
Keyword(s):  
Modulus Of Elasticity ◽  
Drying Shrinkage ◽  
High Water ◽  
Natural Fibre ◽  
Accelerated Ageing ◽  
Flax Fibres ◽  
Aesthetic Appearance ◽  
Cement Binder ◽  
Drying Rates ◽  
Adherence Strength

One of the main functions of renders, together with the overall aesthetic appearance of the building, is the protection of the walls against external aggressive actions, such as water, salts solutions, erosion, and mechanical impacts. However, some anomalies of renders may drastically hinder their protection ability. In fact, cracking, high water permeability, and loss of adherence to the substrate of renders limit their barrier effect and favour the exposure of the substrate to external actions. The incorporation of fibres in mortars is commonly pointed out to reduce their cracking susceptibility, due to the probable enhancement in tensile strength and ductility of the composite. The use of lime in substitution of the part of the cement binder is seen as a method to reduce the modulus of elasticity and therefore enhance the resistance to cracking due to drying shrinkage. Therefore, this study investigates the wall protection-related properties of natural fibre-reinforced renders with cement-lime as a binary binder at 1:1:6 volumetric ratio. With this purpose, wool, coir, and flax fibres are used at 20% by total mortar volume and the water behaviour, cracking susceptibility, and adherence to the substrate of the mortars are assessed. Specifically, the water absorption by capillarity, drying rates, permeability to water under pressure, adherence strength, and shrinkage are evaluated. In order to evaluate the renders’ durability and therefore the durability of the protection to the walls, an artificial accelerated ageing test is performed based on heating-freezing and humidification-freezing cycles. The results indicate that the fibres’ addition reduced the shrinkage and modulus of elasticity of the mortars, which suggests lower susceptibility to cracking. The addition of fibres in mortars seemed to slightly affect their water performance and only at early ages. From the results, it was concluded that the adherence strength is not affected by the fibres’ incorporation. The fibres seem also to reduce the impacts of the ageing cycles on the mortar and the improvements provided by the fibres’ addition to the mortars’ performance remained after ageing when compared to the mortars without fibres, thus being a potential alternative to increase their durability. These aspects are particularly important for buildings, since they can extend their service life and promote their sustainability.

scholarly journals Reinforcing Mechanisms of Coir Fibers in Light-Weight Aggregate Concrete

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 699
Author(s):  
Xiaoxiao Zhang ◽  
Leo Pel ◽  
Florent Gauvin ◽  
David Smeulders
Keyword(s):  
Cement Hydration ◽  
Natural Fibers ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Hydration Reaction ◽  
Light Weight ◽  
Limited Information ◽  
Aggregate Concrete ◽  
Coir Fibers ◽  
Light Weight Aggregate

Due to the requirement for developing more sustainable constructions, natural fibers from agricultural wastes, such as coir fibers, have been increasingly used as an alternative in concrete composites. However, the influence of coir fibers on the hydration and shrinkage of cement-based materials is not clear. In addition, limited information about the reinforcing mechanisms of coir fibers in concrete can be found. The goal of this research is to investigate the effects of coir fibers on the hydration reaction, microstructure, shrinkages, and mechanical properties of cement-based light-weight aggregate concrete (LWAC). Treatments on coir fibers, namely Ca(OH)2 and nano-silica impregnation, are applied to further improve LWAC. Results show that leachates from fibers acting as a delayed accelerator promote cement hydration, and entrained water by fibers facilitates cement hydration during the whole process. The drying shrinkage of LWAC is increased by adding fibers, while the autogenous shrinkage decreases. The strength and toughness of LWAC are enhanced with fibers. Finally, three reinforcement mechanisms of coir fibers in cement composites are discussed.

Sign in / Sign up

Export Citation Format

Share Document