scholarly journals Strength Development and Strain Localization Behavior of Cemented Paste Backfills Using Portland Cement and Fly Ash

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3282 ◽  
Author(s):  
Zhao ◽  
Taheri ◽  
Soltani ◽  
Karakus ◽  
Deng
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Strain Localization ◽  
Image Correlation ◽  
Lateral Strain ◽  
Strength Development ◽  
Curing Time ◽  
Failure Patterns ◽  
Curing Period ◽  
Dic Technique

This study examines the combined performance of Portland cement (PC), the binder, and fly ash (FA), the additive, towards improving the mechanical performance of the South Australian copper-gold underground mine cemented paste backfill (CPB) system. A series of unconfined compressive strength (UCS) tests were carried out on various mix designs to evaluate the effects of binder and/or additive contents, as well as curing time, on the CPB’s strength, stiffness and toughness. Moreover, the failure patterns of the tested samples were investigated by means of the three-dimensional digital image correlation (DIC) technique. Making use of several virtual extensometers, the state of axial and lateral strain localization was also investigated in the pre- and post-peak regimes. The greater the PC content and/or the longer the curing period, the higher the developed strength, stiffness and toughness. The use of FA alongside PC led to further strength and stiffness improvements by way of inducing secondary pozzolanic reactions. Common strength criteria for CPBs were considered to assess the applicability of the tested mix designs; with regards to stope stability, 4% PC + 3% FA was found to satisfy the minimum 700 kPa threshold, and thus was deemed as the optimum choice. As opposed to external measurement devices, the DIC technique was found to provide strain measurements free from bedding errors. The developed field of axial and lateral strains indicated that strain localization initiates in the pre-peak regime at around 80% of the UCS. The greater the PC (or PC + FA) content, and more importantly the longer the curing period, the closer the axial stress level required to initiate localization to the UCS, thus emulating the failure mechanism of quasi-brittle materials such as rock and concrete. Finally, with an increase in curing time, the difference between strain values at the localized and non-localized zones became less significant in the pre-peak regime and more pronounced in the post-peak regime.

scholarly journals Effect of Calcined Hard Kaolin Dosage on the Strength Development of CPB of Fine Tailings with Sulphide

2017 ◽  
Vol 2017 ◽  
pp. 1-7 ◽  
Author(s):  
Juanrong Zheng ◽  
Lijie Guo ◽  
Zhenbo Zhao
Keyword(s):  
Portland Cement ◽  
Pore Diameter ◽  
Strength Development ◽  
Cemented Paste Backfill ◽  
Curing Time ◽  
Curing Period ◽  
Fine Tailings ◽  
Paste Backfill ◽  
Strength And Durability

This study presents the effect of calcined hard kaolin (CHK) as replacement (15–50 wt.%) to Portland cement (PC) on the strength development of cemented paste backfill (CPB) of fine tailings containing sulphide. PC is used as binder at 20 wt.% dosage. The results show that CPB sample containing 30 wt.% CHK replacements produces the desired strength and durability (i.e., 26.1% increase in strength over the curing period between 28 d and 360 d). CPB without CHK does not produce the desired strength and durability (i.e., 32.8% losses in strength over the curing period between 90 d and 360 d). The quantity of expansive gypsum of CPB containing 30 wt.% CHK is obviously less than that of CPB without CHK. The porosity of the fine pore for pore diameter < 0.3 μm is obviously higher in CPB containing 30 wt.% CHK than in CPB without CHK, regardless of curing time. It can be concluded that CHK can be suitably exploited for CPB of fine tailings with sulphide to improve the strength and stability in short and long terms.

scholarly journals Strength Development and Elemental Distribution of Dolomite/Fly Ash Geopolymer Composite under Elevated Temperature

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 1015 ◽  
Author(s):  
Emy Aizat Azimi ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Petrica Vizureanu ◽  
Mohd Arif Anuar Mohd Salleh ◽  
Andrei Victor Sandu ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Liquid Sodium ◽  
Strength Development ◽  
Elemental Distribution ◽  
Distribution Analysis ◽  
Geopolymer Composites

A geopolymer has been reckoned as a rising technology with huge potential for application across the globe. Dolomite refers to a material that can be used raw in producing geopolymers. Nevertheless, dolomite has slow strength development due to its low reactivity as a geopolymer. In this study, dolomite/fly ash (DFA) geopolymer composites were produced with dolomite, fly ash, sodium hydroxide, and liquid sodium silicate. A compression test was carried out on DFA geopolymers to determine the strength of the composite, while a synchrotron Micro-Xray Fluorescence (Micro-XRF) test was performed to assess the elemental distribution in the geopolymer composite. The temperature applied in this study generated promising properties of DFA geopolymers, especially in strength, which displayed increments up to 74.48 MPa as the optimum value. Heat seemed to enhance the strength development of DFA geopolymer composites. The elemental distribution analysis revealed exceptional outcomes for the composites, particularly exposure up to 400 °C, which signified the homogeneity of the DFA composites. Temperatures exceeding 400 °C accelerated the strength development, thus increasing the strength of the DFA composites. This appears to be unique because the strength of ordinary Portland Cement (OPC) and other geopolymers composed of other raw materials is typically either maintained or decreases due to increased heat.

scholarly journals A Step by Step Methodology for Building Sustainable Cementitious Matrices

2020 ◽  
Vol 10 (8) ◽  
pp. 2955 ◽  
Author(s):  
Styliani Papatzani ◽  
Kevin Paine
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume ◽  
Carbon Footprint ◽  
State Of The Art ◽  
Cost Effective ◽  
Strength Development ◽  
Low Carbon ◽  
Current State ◽  
First Time

In an effort to produce cost-effective and environmentally friendly cementitious binders. mainly ternary (Portland cement + limestone + pozzolanas) formulations have been investigated so far. Various proportions of constituents have been suggested, all, however, employing typical Portland cement (PC) substitution rates, as prescribed by the current codes. With the current paper a step by step methodology on developing low carbon footprint binary, ternary and quaternary cementitious binders is presented (PC replacement up to 57%). Best performing binary (60% PC and 40% LS (limestone)) and ternary formulations (60% PC, 20% LS, 20% FA (fly ash) or 43% PC, 20% LS 37% FA) were selected on the grounds of sustainability and strength development and were further optimized with the addition of silica fume. For the first time a protocol for successfully selecting and testing binders was discussed and the combined effect of highly pozzolanic constituents in low PC content formulations was assessed and a number of successful matrices were recommended. The present paper enriched the current state of the art in composite low carbon footprint cementitious binders and can serve as a basis for further enhancements by other researchers in the field.

scholarly journals Effects of Mixing and Curing Temperature on the Strength Development and Pore Structure of Fly Ash Blended Mass Concrete

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Ki-Bong Park ◽  
Takafumi Noguchi
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Pore Structure ◽  
Weather Conditions ◽  
Strength Loss ◽  
Curing Temperature ◽  
Strength Development ◽  
Mass Concrete ◽  
Term Strength

The aim of this work is to know clearly the effects of temperature in response to curing condition, hydration heat, and outside weather conditions on the strength development of high-performance concrete. The concrete walls were designed using three different sizes and three different types of concrete. The experiments were conducted under typical summer and winter weather conditions. Temperature histories at different locations in the walls were recorded and the strength developments of concrete at those locations were measured. The main factors investigated that influence the strength developments of the obtained samples were the bound water contents, the hydration products, and the pore structure. Testing results indicated that the elevated summer temperatures did not affect the early-age strength gain of concrete made using ordinary Portland cement. Strength development was significantly increased at early ages in concrete made using belite-rich Portland cement or with the addition of fly ash. The elevated temperatures resulted in a long-term strength loss in both belite-rich and fly ash containing concrete. The long-term strength loss was caused by a reduction in the degree of hydration and an increase in the total porosity and amount of smaller pores in the material.

Hydration and strength development in ternary portland cement blends containing limestone and fly ash or metakaolin

2013 ◽  
Vol 39 ◽  
pp. 93-103 ◽  
Author(s):  
Kirk Vance ◽  
Matthew Aguayo ◽  
Tandre Oey ◽  
Gaurav Sant ◽  
Narayanan Neithalath
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Strength Development

scholarly journals Elucidating the Pozzolanic Characteristics of Pastes Containing Circulating Fluidized Bed Fly Ash

2015 ◽  
Vol 9 (1) ◽  
pp. 180-186
Author(s):  
Kae-Long Lin ◽  
Chao-Lung Hwang ◽  
Yu-Min Chang
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Fluidized Bed ◽  
Ordinary Portland Cement ◽  
Circulating Fluidized Bed ◽  
Setting Time ◽  
Blended Cement ◽  
Curing Time ◽  
Cement Pastes ◽  
Space Ratio

The aim of this study is to investigate the pozzolanic characteristics of circulating fluidized bed fly ash blended cement (CFBFABC) paste containing circulating fluidized bed fly ash (CFBFA). The initial and final setting time of CFBFABC pastes with CFBFA retards with an increasing CFBFA content. CFBFABC pastes containing 10% CFBFA exhibited a compressive strength similar to that of ordinary Portland cement pastes at the ages of 90 days. X-ray diffraction peaks indicated the presence of portlandite, ettringite, and unreacted C3S (32.6°) and C2 (41.9°). The gel/space ratio of the CFBFABC pastes increased with the curing time and decreased as the CFBFA content increased. The gel/space ratio increased with the curing time because of the progress of hydration, which led to some of the pores being filled. At the ages of 90 days, the gel/space ratio of the CFBFABC pastes containing 10% CFBFA increased to approximately 14%, it is possibly the consumption of Ca(OH)2 and the formation of C-S-H in the CFBFABC pastes. The CFBFABC pastes containing 10% CFBFA did not exhibit any major decrease in the gel/space ratio. It exhibited favorable mechanical characteristics that were observed when the mixing ratio of CFBFA was 10%. Furthermore, CFBFA has the potential, as a pozzolanic material, partially to replace ordinary Portland cement.

Sign in / Sign up

Export Citation Format

Share Document