scholarly journals Wear Mechanisms and Wear Model of Carbide Tools during Dry Drilling of CFRP/TiAl6V4 Stacks

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2843 ◽  
Author(s):  
Unai Alonso Pinillos ◽  
Severo Raúl Fernández Vidal ◽  
Madalina Calamaz ◽  
Franck Andrés Girot Mata
Keyword(s):  
Tool Wear ◽  
Fiber Composite ◽  
Tool Material ◽  
Diffusion Path ◽  
Maximum Temperature ◽  
Carbon Fiber Composite ◽  
Present Contribution ◽  
Auger Analysis ◽  
Weakest Link ◽  
Multiplicative Effect

The present contribution on tool wear during the drilling of carbon fiber composite materials (CFRP)/Ti stacks intends to determine (i) if the adhesion of titanium to carbide is mechanical or chemical, (ii) the possible diffusion path, (iii) if the titanium is the only element involved in the adhesion and (iv) the role of the CFRP in this wear. The overall tool wear is not the sum of the wear in each material and there is a multiplicative effect between them. It has been pointed out that the maximum temperature reached during drilling is higher than 180 °C, 400 °C and 750 °C respectively in the CFRP and Ti plates alone and in the Ti part of the stack. As tungsten carbide CW is not in equilibrium with titanium above 250 °C, the diffusion path is CW/(Ti,W)C/Ti as confirmed by Auger analysis. For temperatures above 500 °C, (Ti,W)C becomes very sensitive to oxidation allowing a friable oxycarbide (Ti,C,O) to form, which explains the erosion of the tool. The CW is therefore the weakest link in the drilling of CFRP/Ti stacks. Improving the performance of the tool involves the use of a coating, the development of a tool material having low chemical affinity with Ti and/or the use of cryogenic lubricant.

Peculiarities of tool material wear at polymeric composite blank cutting

2018 ◽  
Vol 2018 (7) ◽  
pp. 27-31
Author(s):  
Юрий Зубарев ◽  
Yuriy Zubarev ◽  
Александр Приемышев ◽  
Alexsandr Priyomyshev
Keyword(s):  
Tool Wear ◽  
Tool Material ◽  
Polymeric Composite ◽  
Physical Models ◽  
Technological Parameters ◽  
Tool Materials ◽  
Materials Used ◽  
The Impact ◽  
Material Wear

Tool materials used for polymeric composite blank machining, kinds of tool material wear arising at machining these blanks, and also the impact of technological parameters upon tool wear are considered. The obtained results allow estimating the potentialities of physical models at polymeric composite blanks cutting.

Prestressed Carbon Fiber Composite Overwrapped Gun Tube

2008 ◽  
Author(s):  
Andrew Littlefield ◽  
Edward Hyland ◽  
Jack Keating
Keyword(s):  
Carbon Fiber ◽  
Fiber Composite ◽  
Carbon Fiber Composite

scholarly journals Lightweight Cellulose/Carbon Fiber Composite Foam for Electromagnetic Interference (EMI) Shielding

Polymers ◽  
2018 ◽  
Vol 10 (12) ◽  
pp. 1319 ◽  
Author(s):  
Ran Li ◽  
Huiping Lin ◽  
Piao Lan ◽  
Jie Gao ◽  
Yan Huang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Carbon Fibers ◽  
Electromagnetic Interference ◽  
Fiber Composite ◽  
Carbon Fiber Composites ◽  
Shielding Effectiveness ◽  
Electromagnetic Interference Shielding ◽  
Carbon Fiber Composite ◽  
Foaming Process ◽  
Long Carbon Fibers

Lightweight electromagnetic interference shielding cellulose foam/carbon fiber composites were prepared by blending cellulose foam solution with carbon fibers and then freeze drying. Two kinds of carbon fiber (diameter of 7 μm) with different lengths were used, short carbon fibers (SCF, L/D = 100) and long carbon fibers (LCF, L/D = 300). It was observed that SCFs and LCFs built efficient network structures during the foaming process. Furthermore, the foaming process significantly increased the specific electromagnetic interference shielding effectiveness from 10 to 60 dB. In addition, cellulose/carbon fiber composite foams possessed good mechanical properties and low thermal conductivity of 0.021–0.046 W/(m·K).

Sign in / Sign up

Export Citation Format

Share Document