scholarly journals Examining the Influence of Re–Used Nanofiller—Pyrolyzed Montmorillonite, on the Thermal Properties of Polypropylene–Based Engineering Nanocomposites

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2636
Author(s):  
Tomasz M. Majka ◽  
Oskar Bartyzel ◽  
Konstantinos N. Raftopoulos ◽  
Joanna Pagacz ◽  
Krzysztof Pielichowski
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Control Sample ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Stabilization Effect ◽  
Polypropylene Melt ◽  
Better Than

Pyrolysis of the polypropylene/montmorillonite (PP/OMMT) nanocomposites allows for recovery of the filler that can be then re–used to produce PP/pyrolyzed MMT (PMMT) nanostructured composites. In this work, we discuss the thermal properties of PP/PMMT composites investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It has been found that effect of PMMT (5 wt. % and 10 wt. %) on matrix thermal stability occurs at temperatures above 300 °C. Addition of 5 wt. % and 10 wt. % of PMMT into polypropylene system gave good stabilization effect, as confirmed by the overall stabilization effect (OSE) values, which increased by 4% and 7%, respectively, compared to the control sample (PP). Interestingly, the presence of 1 wt. % and 3 wt. % of pyrolyzed clay stabilizes the system better than the same concentrations of organoclay added into polypropylene melt. DSC data revealed that pyrolyzed clay has still the same tendency as organoclay to enhance formation of the α and β crystalline PP phases only. The pyrolyzed MMT causes an improvement of the modulus in the glassy as well as rubbery regions, as confirmed by DMA results.

Thermal properties of a series of tetrafunctional fluorene-based oxazines/P-a blends

2016 ◽  
Vol 29 (10) ◽  
pp. 1139-1147 ◽  
Author(s):  
Zi Sang ◽  
Tiantian Feng ◽  
Wenbin Liu ◽  
Jun Wang ◽  
Mehdi Derradji
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Mechanical Analysis ◽  
Proton Nuclear Magnetic Resonance ◽  
Primary Amines ◽  
Resonance Spectroscopy ◽  
High Glass Transition Temperature ◽  
Scanning Calorimetry ◽  
Good Thermal Stability

A new series of aniline and aniline-mixed tetrafunctional fluorene-based oxazine monomers were synthesized using 2,7-hydroxy-9,9-bis-(4-hydroxyphenyl) fluorene, paraformaldehyde, and primary amines (including aniline or aniline mixed with n-butylamine or n-octylamine composition). Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy were used to characterize the structure of the monomers. The copolymers were obtained by adding the monomers into a typical monofunctional polybenzoxazine (phenol-aniline-based benzoxazine). Differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis were performed to study the thermal properties of the copolymers. The copolymers exhibited high glass transition temperature values (164–201°C). A good thermal stability was also obtained with a 5% weight loss temperature over 355°C and high char yields at 800°C (42–50%).

scholarly journals OPTIMIZING THE WELDING OF PLASTICS WITH THE USE OF DIFFERENTIAL SCANNING CALORIMETRY AND THERMOGRAVIMETRIC ANALYSIS

2014 ◽  
Vol 54 (3) ◽  
pp. 221-224 ◽  
Author(s):  
Michal Ondruška ◽  
Marián Drienovský ◽  
Roman Čička ◽  
Milan Marônek ◽  
Antonín Náplava
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Temperature Regime ◽  
Polymer Chains ◽  
Protective Atmosphere ◽  
Scanning Calorimetry ◽  
Welding Temperature ◽  
Oxidative Atmosphere

Plastics have different thermal stability, depending on the structure of the polymer chains. It is therefore very important to know their thermal properties, which influence the temperature regime of processing equipment. This paper presents examples of differential scanning analysis (DSC) and thermogravimetry analysis (TG) of selected plastics in an Ar protective atmosphere and also in an oxidative atmosphere of static air. These analyses can be used for proposing a welding temperature regime.

Studies on a Miscible Polyimide Blend

1997 ◽  
Vol 9 (3) ◽  
pp. 263-279 ◽  
Author(s):  
J A Campbell ◽  
A A Goodwin ◽  
F W Mercer ◽  
V Reddy
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermogravimetric Analysis ◽  
Physical Aging ◽  
Adhesive Bond ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Adhesive Properties ◽  
Dynamic Mechanical ◽  
Thermal Stability Of

Blends of polyimides XU-218 and PEI were investigated using differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis and adhesive bond testing. The thermal stability of the blends increased as the proportion of PEI increased while the α-relaxation of the blends occurred at a slower rate and was broader and more cooperative in some blends, compared with the pure polymers. Physical aging of the pure polymers and blends in the glass state revealed changes in relaxation rate and lost enthalpy that were also consistent with blends not behaving as simple mixtures. The dynamic mechanical and physical aging behaviour was attributed to an increase in density on blending which decreased the unoccupied volume and increased the constraints on molecular mobility, as well as to the presence of concentration fluctuations. The adhesive properties of the blends were also investigated and bond strength was found to vary with blend composition and test temperature.

Thermal Stability of N-Heterocycle-Stabilized Iodanes – A Systematic Investigation

2019 ◽  
Author(s):  
Andreas Boelke ◽  
Yulia A. Vlasenko ◽  
Mekhman S. Yusubov ◽  
Boris Nachtsheim ◽  
Pavel Postnikov
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermogravimetric Analysis ◽  
Systematic Investigation ◽  
Scanning Calorimetry ◽  
Thermal Stability Of

<p>The thermal stability of pseudocyclic and cyclic <i>N</i>-heterocycle-stabilized (hydroxy)aryl- and mesityl(aryl)-l<sup>3</sup>-iodanes (NHIs) through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) is investigated. NHIs bearing <i>N</i>-heterocycles with a high N/C-ratio such as triazoles show among the lowest descomposition temperatures and the highest decomposition energies. A comparison of NHIs with known (pseudo)cyclic benziodoxolones is made and we further correlated their thermal stability with reactivity in a model oxygenation. </p>

scholarly journals Preparation and Characterization of Talc Filled Thermoplastic Polyurethane/Polypropylene Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Emi Govorčin Bajsić ◽  
Vesna Rek ◽  
Ivana Ćosić
Keyword(s):  
Thermal Properties ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
The Degree Of Crystallinity ◽  
Better Than

The effect of the addition of talc on the morphology and thermal properties of blends of thermoplastic polyurethane (TPU) and polypropylene (PP) was investigated. The blends of TPU and PP are incompatible because of large differences in polarities between the nonpolar crystalline PP and polar TPU and high interfacial tensions. The interaction between TPU and PP can be improved by using talc as reinforcing filler. The morphology was observed by means of scanning electron microscopy (SEM). The thermal properties of the neat polymers and unfilled and talc filled TPU/PP blends were studied by using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The addition of talc in TPU/PP blends improved miscibility in all investigated TPU/T/PP blends. The DSC results for talc filled TPU/PP blends show that the degree of crystallinity increased, which is due to the nucleating effect induced by talc particles. The reason for the increased storage modulus of blends with the incorporation of talc is due to the improved interface between polymers and filler. According to TGA results, the addition of talc enhanced thermal stability. The homogeneity of the talc filled TPU/PP blends is better than unfilled TPU/PP blends.

scholarly journals Conversion of palm oil to new sulfur-based polymer by inverse vulcanization

2021 ◽  
Vol 287 ◽  
pp. 02014
Author(s):  
Amin Abbasi ◽  
Mohamed Mahmoud Nasef ◽  
Wan Zaireen Nisa Yahya ◽  
Muhammad Moniruzzaman
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Fourier Transform ◽  
Thermogravimetric Analysis ◽  
Palm Oil ◽  
Elemental Sulfur ◽  
Molten State ◽  
Scanning Calorimetry ◽  
Environmental Friendly ◽  
Sulfur Containing

The conversion of palm oil into a sulfur-based polymer by copolymerization with sulfur powder at its molten state is herein reported. The obtained sulfur-containing polymer was characterized using Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) to demonstrate the successful conversion. The disappearance of the peaks related to vinylic groups of oil together with the appearance of a peak representing C-H rocking vibrations in the vicinity of C-S bonds confirmed the copolymerization of sulfur with oil. TGA revealed that the polymers have thermal stability up to 230°C under nitrogen and the polymers leave 10% sulfur-rich ash. DSC proved that a small amount of elemental sulfur remained unreacted in the polymer, which showed amorphous and heavily crosslinked structure resembling thermosets. These copolymers are an environmental-friendly polymeric material promoting the utilization of the abundant sulfur while also adding value to palm oil.

A Deep Blue Organic Light Emitting Diodes Characteristic of Isomerically-Featured Phosphine Oxides Containing N-Phenyl Benzimidazole

2020 ◽  
Vol 20 (8) ◽  
pp. 4657-4660
Author(s):  
Kyeong Hyeon Kim ◽  
Jae Hyeok Lee ◽  
Dong-Eun Kim ◽  
Hoon-Kyu Shin ◽  
Burm-Jong Lee
Keyword(s):  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Light Emitting Diodes ◽  
Organic Light Emitting Diodes ◽  
Phosphine Oxides ◽  
Scanning Calorimetry ◽  
Light Emitting ◽  
Deep Blue ◽  
Organic Light

An isomeric series of phosphine oxides with N-phenyl benzimidazole such as 2-DPPI, 3-DPPI and 4-DPPI were synthesized for organic light emitting diodes (OLED). The thermal properties of DPPI isomers were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). OLED devices using DPPI isomers as the emitting material were fabricated, which configuration was ITO/MoOx [30 nm]/NPB [500 nm]/DPPI [300 nm]/Alq3 [200 nm]/Liq[10 nm]/Al [120 nm]. The emitting colors of the devices were respectively a deep-blue (430 nm, 4-DPPI) and greenish-yellows (510–580 nm, 3-DPPI and 530 nm, 2-DPPI). In particular, the emitting color of 4-DPPI device was not changed during the alteration of applied voltages (6.5–11.5 V), and the CIE coordinate was a satisfactory deep-blue (0.161, 0.101).

Application of ionic liquid [bmim]PF6 as green plasticizer for poly(L-lactide)

e-Polymers ◽  
2008 ◽  
Vol 8 (1) ◽  
Author(s):  
Puyu Zhang ◽  
Lichao Peng ◽  
Wenbin Li
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Ionic Liquid ◽  
Glass Transition ◽  
Transition Temperature ◽  
Poly Ethylene Glycol ◽  
Scanning Calorimetry ◽  
Poly Ethylene ◽  
Thermal Stability Of ◽  
Better Than

AbstractIonic liquid [bmim]PF6 (1-butyl-3-methylimidazolium hexafluoro phosphate) was synthesized and characterized. It was used as the plasticizer for poly(L-lactide) (PLLA). The glass transition temperature (Tg) and the thermal stability of the plasticized PLLA samples were measured by thermogravimetry (TG) and differential scanning calorimetry (DSC). Compared with poly(ethylene glycol) having Mw of 300 g/mol (PEG300), TG results showed that the thermal stability of PLLA plasticized with ionic liquid was better than that of PLLA plasticized with PEG300. The Tg of plasticized PLLA decrease with increasing the content of ionic liquid [bmim]PF6 from 2 wt.% to 10 wt.%. The Tg of PLLA can be reduced to 40°C when the content of ionic liquid [bmim]PF6 was 10 wt.%. The materials of PLLA with plasticizer were also investigated using polarizing microscope (POM), the results of which indicate that the movements of PLLA chains were improved when ionic liquid plasticizer was used.

Synthesis and Thermal Stability of Unsaturated Polyamides

1992 ◽  
Vol 4 (2) ◽  
pp. 67-71
Author(s):  
N. R. Patel ◽  
N. Z. Patel ◽  
R. M. Patel
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermogravimetric Analysis ◽  
Scanning Calorimetry ◽  
Aromatic Diamines ◽  
Good Thermal Stability ◽  
Kinetics Of Decomposition ◽  
Glutaconic Acid ◽  
Kinetics Of ◽  
Thermal Stability Of

Unsaturated polyamides were prepared by condensing /3(4-ethoxyphenyl) glutaconic acid with various aromatic diamines. The polycondensates were characterized by IR spectroscopy, vapor phase osmometry, thermogravimetric analysis, differential scanning calorimetry and elemental analysis. All resins were found to decompose in the range '-210-600 °C. The kinetics of decomposition were studied. The results indicated that the resins possess reasonably good thermal stability.

scholarly journals Morphological and thermal properties of composites prepared with poly(lactic acid), poly(ethylene-alt-maleic anhydride), and biochar from microwave-pyrolyzed jatropha seeds

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 3171-3185
Author(s):  
Perry Law Nyuk Khui ◽  
Rezaur Rahman ◽  
Abu Saleh Ahmed ◽  
Kuok King Kuok ◽  
Muhammad Khusairy Bin Bakri ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Fourier Transform ◽  
Thermal Properties ◽  
Infrared Spectroscopy ◽  
Fourier Transform Infrared Spectroscopy ◽  
Filler Content ◽  
Scanning Calorimetry ◽  
Jatropha Seeds ◽  
Properties Of Composites

The morphological and thermal properties of composites containing a bioplastic blend and micro/nano-sized biochar from pyrolyzed jatropha seeds from microwave pyrolyzed jatropha seeds were investigated using scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The biocomposite samples exhibited a brittle structure with a slightly ductile chip-like appearance. The Fourier transform infrared spectroscopy results for the PLA/PEMA/BC bio-composites were comparable to the PLA/BC biocomposites. A lower bio-filler content had more pronounced peak intensities than the higher bio-filler content biocomposites. The added PEMA compatibilizer in the PLA/PEMA/BC biocomposite showed more pronounced peaks, which indicated slightly improved bonding/interaction between the bio-filler and the matrix. Overall, increasing bio-filler content did not drastically affect the functional groups of the biocomposites. Thermogravimetric and differential scanning calorimetry analysis showed the developed biocomposites had a slight improvement in thermal stability, in comparison to the PLA sample. Improvements in the thermal stability of the PLA/PEMA/BC biocomposite could be attributed to the additional hydroxyl group, which was due to the added PEMA in the PLA and PLA/BC. According to the results of the analysis of the developed biocomposites, the biocomposites were more brittle and had reasonable thermal stability.

Sign in / Sign up

Export Citation Format

Share Document