scholarly journals Design and Fabrication of Random Metal Foam Structures for Laser Powder Bed Fusion

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1301 ◽  
Author(s):  
Nicola Contuzzi ◽  
Sabina Luisa Campanelli ◽  
Fabrizia Caiazzo ◽  
Vittorio Alfieri
Keyword(s):  
Additive Manufacturing ◽  
Metal Foam ◽  
Design Stage ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Proper Actions ◽  
Fractional Density ◽  
Technical Requirements ◽  
Crucial Information

With the development of additive manufacturing, the building of new categories of lightweight structures such as random foams have been offered. Nevertheless, given the complexity of the required parts, macroscopic defects may result or the process may even fail. Therefore, proper actions must be taken at the design stage. In this paper, a method of design for additive manufacturing (DfAM) to build metal random foam structures is proposed. Namely, a procedure is suggested to generate a structure that has interconnected porosity. This procedure is based on the aimed fractional density and several technical requirements, and then the geometry is optimized and meshed. To validate the algorithm, a test article consisting of a metal cylinder with spherical random pores ranging from 1 to 6 mm in diameter with a resulting fractional density of 40 ± 2% has been conceived and manufactured by means of laser powder bed fusion (LPBF). On the basis of the outcome of the manufacturing process, crucial information has been gathered to update the algorithm.

scholarly journals On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 538 ◽  
Author(s):  
Fabrizia Caiazzo ◽  
Vittorio Alfieri ◽  
Giuseppe Casalino
Keyword(s):  
Surface Roughness ◽  
Energy Density ◽  
Process Parameters ◽  
Vickers Hardness ◽  
Powder Bed Fusion ◽  
Processing Conditions ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Fractional Density ◽  
Experimental Variation

Laser powder bed fusion (LPBF) can fabricate products with tailored mechanical and surface properties. In fact, surface texture, roughness, pore size, the resulting fractional density, and microhardness highly depend on the processing conditions, which are very difficult to deal with. Therefore, this paper aims at investigating the relevance of the volumetric energy density (VED) that is a concise index of some governing factors with a potential operational use. This paper proves the fact that the observed experimental variation in the surface roughness, number and size of pores, the fractional density, and Vickers hardness can be explained in terms of VED that can help the investigator in dealing with several process parameters at once.

scholarly journals GEOMETRICAL BENCHMARKING OF LASER POWDER BED FUSION SYSTEMS BASED ON DESIGNER NEEDS

2021 ◽  
Vol 1 ◽  
pp. 1657-1666
Author(s):  
Joaquin Montero ◽  
Sebastian Weber ◽  
Christoph Petroll ◽  
Stefan Brenner ◽  
Matthias Bleckmann ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Use Case ◽  
Powder Bed Fusion ◽  
Design For Additive Manufacturing ◽  
Laser Powder Bed Fusion ◽  
Measuring Systems ◽  
Powder Bed ◽  
Geometric Dimensioning And Tolerancing ◽  
Uncertainty Map ◽  
New System

AbstractCommercially available metal Laser Powder Bed Fusion (L-PBF) systems are steadily evolving. Thus, design limitations narrow and the diversity of achievable geometries widens. This progress leads researchers to create innovative benchmarks to understand the new system capabilities. Thereby, designers can update their knowledge base in design for additive manufacturing (DfAM). To date, there are plenty of geometrical benchmarks that seek to develop generic test artefacts. Still, they are often complex to measure, and the information they deliver may not be relevant to some designers. This article proposes a geometrical benchmarking approach for metal L-PBF systems based on the designer needs. Furthermore, Geometric Dimensioning and Tolerancing (GD&T) characteristics enhance the approach. A practical use-case is presented, consisting of developing, manufacturing, and measuring a meaningful and straightforward geometric test artefact. Moreover, optical measuring systems are used to create a tailored uncertainty map for benchmarking two different L-PBF systems.

scholarly journals Gold, Silver, and Electrum Electroless Plating on Additively Manufactured Laser Powder-Bed Fusion AlSi10Mg Parts: A Review

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Dana Ashkenazi ◽  
Alexandra Inberg ◽  
Yosi Shacham-Diamand ◽  
Adin Stern
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Ion Beam ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Process ◽  
Gold Silver ◽  
3D Printed

Additive manufacturing (AM) revolutionary technologies open new opportunities and challenges. They allow low-cost manufacturing of parts with complex geometries and short time-to-market of products that can be exclusively customized. Additive manufactured parts often need post-printing surface modification. This study aims to review novel environmental-friendly surface finishing process of 3D-printed AlSi10Mg parts by electroless deposition of gold, silver, and gold–silver alloy (e.g., electrum) and to propose a full process methodology suitable for effective metallization. This deposition technique is simple and low cost method, allowing the metallization of both conductive and insulating materials. The AlSi10Mg parts were produced by the additive manufacturing laser powder bed fusion (AM-LPBF) process. Gold, silver, and their alloys were chosen as coatings due to their esthetic appearance, good corrosion resistance, and excellent electrical and thermal conductivity. The metals were deposited on 3D-printed disk-shaped specimens at 80 and 90 °C using a dedicated surface activation method where special functionalization of the printed AlSi10Mg was performed to assure a uniform catalytic surface yielding a good adhesion of the deposited metal to the substrate. Various methods were used to examine the coating quality, including light microscopy, optical profilometry, XRD, X-ray fluorescence, SEM–energy-dispersive spectroscopy (EDS), focused ion beam (FIB)-SEM, and XPS analyses. The results indicate that the developed coatings yield satisfactory quality, and the suggested surface finishing process can be used for many AM products and applications.

scholarly journals Laser powder bed fusion additive manufacturing of highly conductive parts made of optically absorptive carburized CuCr1 powder

2021 ◽  
Vol 198 ◽  
pp. 109369
Author(s):  
Suraj Dinkar Jadhav ◽  
Pushkar Prakash Dhekne ◽  
Etienne Brodu ◽  
Brecht Van Hooreweder ◽  
Sasan Dadbakhsh ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed
Sign in / Sign up

Export Citation Format

Share Document