scholarly journals Fabrication of Nanopillar Crystalline ITO Thin Films with High Transmittance and IR Reflectance by RF Magnetron Sputtering

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 958 ◽  
Author(s):  
Ling Dong ◽  
Guisheng Zhu ◽  
Huarui Xu ◽  
Xupeng Jiang ◽  
Xiuyun Zhang ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Indium Tin Oxide ◽  
Rf Magnetron Sputtering ◽  
Light Transmittance ◽  
Electrical Performance ◽  
Soda Lime Glass ◽  
Crystalline Film ◽  
Ito Thin Films

Nanopillar crystalline indium tin oxide (ITO) thin films were deposited on soda-lime glass substrates by radio frequency (RF) magnetron sputtering under the power levels of 100 W, 150 W, 200 W and 250 W. The preparation process of thin films is divided into two steps, firstly, sputtering a very thin and granular crystalline film at the bottom, and then sputtering a nanopillar crystalline film above the bottom film. The structure, morphology, optical and electrical properties of the nanopillar crystalline ITO thin films were investigated. From X-ray diffraction (XRD) analysis, the nanopillar crystalline thin films shows (400) preferred orientation. Due to the effect of the bottom granular grains, the crystallinity of the nanopillar crystals on the upper layer was greatly improved. The nanopillar crystalline ITO thin films exhibited excellent electrical properties, enhanced visible light transmittance and a highly infrared reflectivity in the mid-infrared region. It is noted that the thin film deposited at 200 W showed the best combination of optical and electrical performance, with resistivity of 1.44 × 10−4 Ω cm, average transmittance of 88.49% (with a film thickness of 1031 nm) and IR reflectivity reaching 89.18%.

Properties of Indium Tin Oxide Films Prepared by RF Magnetron Sputtering at Different Substrate Temperatures

2012 ◽  
Vol 502 ◽  
pp. 77-81
Author(s):  
Z.Y. Zhong ◽  
J.H. Gu ◽  
X. He ◽  
C.Y. Yang ◽  
J. Hou
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Visible Region ◽  
Rf Magnetron Sputtering ◽  
X Ray ◽  
Ito Thin Films

Indium tin oxide (ITO) thin films were deposited by RF magnetron sputtering on glass substrates employing a sintered ceramic target. The influence of substrate temperature on the structural, compositional, optical and electrical properties of the thin films were investigated by X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS), spectrophotometer and four-point probes. All the ITO thin films show a polycrystalline indium oxide structure and have a preferred orientation along the (222) direction. The substrate temperature significantly affects the crystal structure and optoelectrical properties of the thin films. With the increment of substrate temperature, the electrical resistivity of the deposited films decreases, the crystallite dimension, optical bandgap and average transmittance in the visible region increase. The ITO thin film deposited at substrate temperature of 200 °C possesses the best synthetic optoelectrical properties, with the highest transmittance, the lowest resistivity and the highest figure of merit.

Structural and Optical Properties of Nickel (Ni)/indium Tin Oxide (ITO) Thin-Films Deposited by RF Magnetron Sputtering

2014 ◽  
Vol 895 ◽  
pp. 181-185 ◽  
Author(s):  
M. Sobri ◽  
A. Shuhaimi ◽  
M. Mazwan ◽  
K.M. Hakim ◽  
S. Najwa ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Magnetron Sputtering ◽  
Tin Oxide ◽  
Indium Tin Oxide ◽  
Seed Layer ◽  
Rf Magnetron Sputtering ◽  
Sample Surface ◽  
Deposition Parameter ◽  
Ito Thin Films

Nickel (Ni)/ indium tin oxide (ITO) thin-films have been deposited on silicon (Si) and glass substrates using radio-frequency (RF) magnetron sputtering at 200°C temperature. ITO layer was deposited on top of Ni layer with various deposition parameter. The material and optical properties of the ITO samples with and without Ni seed layer were analyzed. X-ray diffraction studies shows that the films are crystalline with the typical ITO diffraction peaks of (222), (400) and (411). The FESEM and AFM images shows that the grains have uniform shapes and sizes. FESEM results reveal that the grain size along the sample surface decreases when the Ni seed layer is added. Both the samples shows higher transmittance of more than 95% in UV-vis spectrometer.

Characteristics of Ion Beam Assisted ITO Thin Films Deposited by RF Magnetron Sputtering

2014 ◽  
Vol 601 (1) ◽  
pp. 57-63 ◽  
Author(s):  
Kyong Chan Heo ◽  
Phil Kook Son ◽  
Youngku Sohn ◽  
Jonghoon Yi ◽  
Jin Hyuk Kwon ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Ion Beam ◽  
Rf Magnetron Sputtering ◽  
Ito Thin Films

scholarly journals Residual Oxygen Effects on the Properties of MoS2 Thin Films Deposited at Different Temperatures by Magnetron Sputtering

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1183
Author(s):  
Peiyu Wang ◽  
Xin Wang ◽  
Fengyin Tan ◽  
Ronghua Zhang
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Deposition Rate ◽  
Deposition Temperature ◽  
Energy Dispersive Spectrometer ◽  
Rf Magnetron Sputtering ◽  
Glass Substrates ◽  
Different Temperatures ◽  
Oxygen Atoms

Molybdenum disulfide (MoS2) thin films were deposited at different temperatures (150 °C, 225 °C, 300 °C, 375 °C, and 450 °C) on quartz glass substrates and silicon substrates using the RF magnetron sputtering method. The influence of deposition temperature on the structural, optical, electrical properties and deposition rate of the obtained thin films was investigated by X-ray diffraction (XRD), Energy Dispersive Spectrometer (EDS), Raman, absorption and transmission spectroscopies, a resistivity-measuring instrument with the four-probe method, and a step profiler. It was found that the MoS2 thin films deposited at the temperatures of 150 °C, 225 °C, and 300 °C were of polycrystalline with a (101) preferred orientation. With increasing deposition temperatures from 150 °C to 300 °C, the crystallization quality of the MoS2 thin films was improved, the Raman vibrational modes were strengthened, the deposition rate decreased, and the optical transmission and bandgap increased. When the deposition temperature increased to above 375 °C, the molecular atoms were partially combined with oxygen atoms to form MoO3 thin film, which caused significant changes in the structural, optical, and electrical properties of the obtained thin films. Therefore, it was necessary to control the deposition temperature and reduce the contamination of oxygen atoms throughout the magnetron sputtering process.

Silicon Germanium Oxide (SixGeyO1-x-y) Infrared Sensitive Material for Uncooled Detectors

2010 ◽  
Vol 1245 ◽  
Author(s):  
Reza Anvari ◽  
Qi Cheng ◽  
Muhammad Lutful Hai ◽  
Truc Phan Bui ◽  
A. J. Syllaios ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Silicon Germanium ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Germanium Oxide ◽  
Temperature Coefficient Of Resistance ◽  
Sensitive Material

AbstractThis paper presents the formation and the characterization of silicon germanium oxide (SixGeyO1-x-y) infrared sensitive material for uncooled microbolometers. RF magnetron sputtering was used to simultaneously deposit Si and Ge thin films in an Ar/O2 environment at room temperature. The effects of varying Si and O composition on the thin film's electrical properties which include temperature coefficient of resistance (TCR) and resistivity were investigated. The highest achieved TCR and the corresponding resistivity at room temperature were -5.41 %/K and 3.16×103 ohm cm using Si0.039Ge0.875O0.086 for films deposited at room temperature.

Crystal Growth of β-FeSi2 Thin Film on (100), (110) and (111) Plane of Si and Yittria-stabilized Zirconia Substrates

2006 ◽  
Vol 980 ◽  
Author(s):  
Kensuke Akiyama ◽  
Satoru Kaneko ◽  
Takanori Kiguchi ◽  
Takashi Suemasu ◽  
Takeshi Kimura ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Crystal Growth ◽  
Magnetron Sputtering ◽  
Iron Silicide ◽  
Rf Magnetron Sputtering ◽  
Single Element ◽  
Stabilized Zirconia ◽  
Crystalline Film ◽  
Anions And Cations

AbstractIron silicide thin films were prepared on silicon (Si) and yittria-stabilized zirconia (YSZ) substrates using RF magnetron sputtering and evaporation methods. Epitaxial b-FeSi2 thin films were grown on (100) and (111) planes of Si and YSZ substrates, while noncrystallized films were deposited on (110) plane of both Si and YSZ substrates. The epitaxial relationships between the b-FeSi2 and YSZ were the same as those between b-FeSi2 and Si, in the case of (100) and (111) planes. It is possible that epitaxial b-FeSi2 film can be grown when substrates and b-FeSi2 surfaces consist of either a single element or only cations, while the crystalline film was not shown when either substrate or b-FeSi2 surface consists of a mixture of anions and cations or iron and silicon.

RF Magnetron Sputtering Processed Transparent Conductive Aluminum Doped ZnO thin Films with Excellent Optical and Electrical Properties

2021 ◽  
Author(s):  
Chunhu Zhao ◽  
Junfeng Liu ◽  
Yixin Guo ◽  
Yanlin Pan ◽  
Xiaobo Hu ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Carrier Concentration ◽  
Rf Magnetron Sputtering ◽  
Zno Thin Films ◽  
Band Model ◽  
Deposition Condition ◽  
Optical And Electrical Properties ◽  
Doped Zno

Abstract Aluminum doped ZnO thin films (AZO), which simultaneously transmit light and conduct electrical current, are widely applied in photovoltaic devices. To achieve high performance AZO thin films, the effects of RF magnetron sputtering conditions on the optical and electrical properties of the films has been explored. The optimized AZO thin films exhibit strong (002) orientated growth with hexagonal wurtzite structure. The minimum resistivity of 0.9Í10-3 Ω·cm, the highest carrier concentration of 2.8Í1020 cm-3, the best Hall mobility of 22.8 cm2·(V·s)-1 and average transmittance above 85% can be achieved at the optimum deposition condition of 0.2 Pa, 120 W and 200 °C. Considering the single parabolic band model, the bandgap shift by carrier concentration of the films can be attributed to the Burstein-Moss effect. The results indicate that RF magnetron sputtered AZO thin films are promising for solar cell applications relying on front contact layers.

Sign in / Sign up

Export Citation Format

Share Document