scholarly journals Thermoelectric Properties of Ca3Co2−xMnxO6 (x = 0.05, 0.2, 0.5, 0.75, and 1)

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 497 ◽  
Author(s):  
Nikola Kanas ◽  
Sathya Singh ◽  
Magnus Rotan ◽  
Temesgen Desissa ◽  
Tor Grande ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Self Assembly ◽  
Intermediate Phase ◽  
Small Polaron ◽  
Solid State Method ◽  
Polaron Hopping ◽  
Seebeck Coefficients ◽  
Conventional Sintering

High-temperature instability of the Ca3Co4−yO9+δ and CaMnO3−δ direct p-n junction causing the formation of Ca3Co2−xMnxO6 has motivated the investigation of the thermoelectric performance of this intermediate phase. Here, the thermoelectric properties comprising Seebeck coefficient, electrical conductivity, and thermal conductivity of Ca3Co2−xMnxO6 with x = 0.05, 0.2, 0.5, 0.75, and 1 are reported. Powders of the materials were synthesized by the solid-state method, followed by conventional sintering. The material Ca3CoMnO6 (x = 1) demonstrated a large positive Seebeck coefficient of 668 μV/K at 900 °C, but very low electrical conductivity. Materials with compositions with x < 1 had lower Seebeck coefficients and higher electrical conductivity, consistent with small polaron hopping with an activation energy for mobility of 44 ± 6 kJ/mol and where both the concentration and mobility of hole charge carriers were proportional to 1−x. The conductivity reached about 11 S·cm−1 at 900 °C for x = 0.05. The material Ca3Co1.8Mn0.2O6 (x = 0.2) yielded a maximum zT of 0.021 at 900 °C. While this value in itself is not high, the thermodynamic stability and self-assembly of Ca3Co2−xMnxO6 layers between Ca3Co4−yO9+δ and CaMnO3−δ open for new geometries and designs of oxide-based thermoelectric generators.

Band Structure and Thermoelectric Properties of Ni(x)Zn(1-x)Fe2O4

2021 ◽  
Vol 317 ◽  
pp. 28-34
Author(s):  
Joon Hoong Lim
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Band Structure ◽  
Seebeck Coefficient ◽  
Band Gap ◽  
Thermoelectric Properties ◽  
Xrd Analysis ◽  
Valence Band Maximum ◽  
Solid State Method ◽  
Ni Content

Thermoelectric materials has made a great potential in sustainable energy industries, which enable the energy conversion from heat to electricity. The band structure and thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 have been investigated. The bulk pellets were prepared from analytical grade ZnO, NiO and Fe2O3 powder using solid-state method. It was possible to obtain high thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 by controlling the ratios of dopants and the sintering temperature. XRD analysis showed that the fabricated samples have a single phase formation of cubic spinel structure. The thermoelectric properties of Ni(x)Zn(1-x)Fe2O4 pellets improved with increasing Ni. The electrical conductivity of Ni(x)Zn(1-x)Fe2O4 pellets decreased with increasing Ni content. The electrical conductivity of Ni(x)Zn(1-x)Fe2O4 (x = 0.0) is (0.515 x10-3 Scm-1). The band structure shows that ZnxCu1-xFe2O4 is an indirect band gap material with the valence band maximum (VBM) at M and conduction band minimum (CBM) at A. The band gap of Ni(x)Zn(1-x)Fe2O4 increased with increasing Ni content. The increasing band gap correlated with the lower electrical conductivity. The thermal conductivity of Ni(x)Zn(1-x)Fe2O4 pellets decreased with increasing Ni content. The presence of Ni served to decrease thermal conductivity by 8 Wm-1K-1 over pure samples. The magnitude of the Seebeck coefficient for Ni(x)Zn(1-x)Fe2O4 pellets increased with increasing amounts of Ni. The figure of merit for Ni(x)Zn(1-x)Fe2O4 pellets and thin films was improved by increasing Ni due to its high Seebeck coefficient and low thermal conductivity.

Preparation and Thermoelectric Properties of (Ca1-x-yKxBiy)3Co4O9 Ceramic

2008 ◽  
Vol 368-372 ◽  
pp. 559-561 ◽  
Author(s):  
Hao Ming Hu ◽  
Yuan Deng ◽  
Jian Li ◽  
Guang Sheng Wang
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Transport Properties ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Room Temperature ◽  
Raw Materials ◽  
Sol Gel ◽  
Sintering Process ◽  
Conventional Sintering

The precursor of (Ca1-x-yKxBiy)3Co4O9 was synthesized by sol-gel method using nitrate salts as raw materials and citrate acid as agent. The final product was obtained after the precursor was calcined at 800°C for 4 h. The polycrystalline bulk samples were fabricated by a conventional sintering process at 900°C for 12 h. XRD and SEM were used to characterize the microstructures and the composition of the samples. The transport properties of the samples at room temperature were determined by measuring electrical conductivity and Seebeck coefficient. The Bi and K-doped samples show an excellent transport properties even at room temperature. The value of power factor of (Ca0.90K0.075Bi0.025)3Co4O9 reaches 1.42×10-4Wm-1K-2 at 293K, close to the performance of pure Ca3Co4O9 at 1000K.

scholarly journals DC conductivity and Seebeck coefficient of nonstoichiometric MgCuZn ferrites

2017 ◽  
Vol 35 (1) ◽  
pp. 40-44 ◽  
Author(s):  
W. Madhuri ◽  
S. Roopas Kiran ◽  
M. Penchal Reddy ◽  
N. Ramamanohar Reddy ◽  
K.V. Siva Kumar
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Small Polaron ◽  
X Ray Diffraction ◽  
High Definition ◽  
Conventional Solid State Reaction ◽  
Polaron Hopping ◽  
Dc Electrical Conductivity ◽  
Phase Spinel ◽  
Diffraction Patterns

AbstractNonstoichiometric series of Mg0.5−xCuxZn0.5Fe1.9O4−δ where x = 0.0, 0.1, 0.15, 0.2 and 0.25 has been synthesized by conventional solid state reaction route. The single phase spinel structure of the double sintered ferrites was confirmed by X-ray diffraction patterns (XRD). The ferrite series was studied in terms of DC electrical conductivity and thermoelectric power in the temperature ranging from room temperature to 300 °C and 400 °C, respectively. It was observed that DC electrical conductivity and Seebeck coefficient α decreased with the increase in x. DC electrical conductivity was found to decrease by about 4 orders. All the compositions showed a negative Seebeck coefficient exhibiting n-type semiconducting nature. From the above experimental results, activation energy and mobility of all the samples were estimated. Small polaron hopping conduction mechanism was suggested for the series of ferrites. Owing to their low conductivity the nonstoichiometric MgCuZn ferrites are the best materials for transformer core and high definition television deflection yokes.

scholarly journals Blend Structure and n-Type Thermoelectric Performance of PA6/SAN and PA6/PMMA Blends Filled with Singlewalled Carbon Nanotubes

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1146
Author(s):  
Beate Krause ◽  
Alice Liguoro ◽  
Petra Pötschke
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Immiscible Blends ◽  
Seebeck Coefficients ◽  
Selective Localization ◽  
The Absolute ◽  
Pmma Blends ◽  
Absolute Seebeck Coefficient

The present study investigates how the formation of melt-mixed immiscible blends based on PA6/SAN and PA6/PMMA filled with single walled nanotubes (SWCNTs) affects the thermoelectric (TE) properties. In addition to the detailed investigation of the blend morphology with compositions between 100/0 wt.% and 50/50 wt.%, the thermoelectric properties are investigated on blends with different SWCNT concentrations (0.25–3.0 wt.%). Both PA6 and the blend composites with the used type of SWCNTs showed negative Seebeck coefficients. It was shown that the PA6 matrix polymer, in which the SWCNTs are localized, mainly influenced the thermoelectric properties of blends with high SWCNT contents. By varying the blend composition, an increase in the absolute Seebeck coefficient, power factor (PF), and figure of merit (ZT) was achieved compared to the PA6 composite which is mainly related to the selective localization and enrichment of SWCNTs in the PA6 matrix at constant SWCNT loading. The maximum PFs achieved were 0.22 µW/m·K2 for PA6/SAN/SWCNT 70/30/3 wt.% and 0.13 µW/m·K2 for PA6/PMMA/SWCNT 60/40/3 wt.% compared to 0.09 µW/m·K2 for PA6/3 wt.% SWCNT which represent increases to 244% and 144%, respectively. At higher PMMA or SAN concentration, the change from matrix-droplet to a co-continuous morphology started, which, despite higher SWCNT enrichment in the PA6 matrix, disturbed the electrical conductivity, resulting in reduced PFs with still increasing Seebeck coefficients. At SWCNT contents between 0.5 and 3 wt.% the increase in the absolute Seebeck coefficient was compensated by lower electrical conductivity resulting in lower PF and ZT as compared to the PA6 composites.

scholarly journals Boron Doping of SWCNTs as a Way to Enhance the Thermoelectric Properties of Melt-Mixed Polypropylene/SWCNT Composites

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 394 ◽  
Author(s):  
Beate Krause ◽  
Viktor Bezugly ◽  
Vyacheslav Khavrus ◽  
Liu Ye ◽  
Gianaurelio Cuniberti ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Boron Doping ◽  
Degree Of Crystallinity ◽  
Melt Mixing ◽  
Seebeck Coefficients ◽  
The Matrix ◽  
Order Of Magnitude ◽  
Walled Carbon Nanotubes

Composites based on the matrix polymer polypropylene (PP) filled with single-walled carbon nanotubes (SWCNTs) and boron-doped SWCNTs (B-SWCNTs) were prepared by melt-mixing to analyze the influence of boron doping of SWCNTs on the thermoelectric properties of these nanocomposites. It was found that besides a significantly higher Seebeck coefficient of B-SWCNT films and powder packages, the values for B-SWCNT incorporated in PP were higher than those for SWCNTs. Due to the higher electrical conductivity and the higher Seebeck coefficients of B-SWCNTs, the power factor (PF) and the figure of merit (ZT) were also higher for the PP/B-SWCNT composites. The highest value achieved in this study was a Seebeck coefficient of 59.7 µV/K for PP with 0.5 wt% B-SWCNT compared to 47.9 µV/K for SWCNTs at the same filling level. The highest PF was 0.78 µW/(m·K2) for PP with 7.5 wt% B-SWCNT. SWCNT macro- and microdispersions were found to be similar in both composite types, as was the very low electrical percolation threshold between 0.075 and 0.1 wt% SWCNT. At loadings between 0.5 and 2.0 wt%, B-SWCNT-based composites have one order of magnitude higher electrical conductivity than those based on SWCNT. The crystallization behavior of PP is more strongly influenced by B-SWCNTs since their composites have higher crystallization temperatures than composites with SWCNTs at a comparable degree of crystallinity. Boron doping of SWCNTs is therefore a suitable way to improve the electrical and thermoelectric properties of composites.

The Influence of Silicon Dopant and Processing on Thermoelectric Properties of B4C Ceramics

1998 ◽  
Vol 545 ◽  
Author(s):  
Ke-Feng Cai ◽  
Ce-Wen Nan ◽  
Xin-Min Min
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Hot Pressing ◽  
Figure Of Merit ◽  
Room Temperature ◽  
A Value ◽  
Si Doped

AbstractB4C ceramics doped with various content of Si (0 to 2.03 at%) are prepared via hot pressing. The composition and microstructure of the ceramics are characterized by means of XRD and EPMA. Their electrical conductivity and Seebeck coefficient of the samples are measured from room temperature up to 1500K. The electrical conductivity increases with temperature, and more rapidly after 1300K; the Seebeck coefficient of the ceramics also increases with temperature and rises to a value of about 320μVK−1. The value of the figure of merit of Si-doped B4C rises to about 4 × 10−4K−1 at 1500K.

scholarly journals Preparation and Thermoelectric Properties of Graphite/poly(3,4-ethyenedioxythiophene) Nanocomposites

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2849 ◽  
Author(s):  
Yong Du ◽  
Haixia Li ◽  
Xuechen Jia ◽  
Yunchen Dou ◽  
Jiayue Xu ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Oxidative Polymerization ◽  
Polymerization Process ◽  
Measurement Temperature ◽  
Temperature Range ◽  
Different Content

Graphite/poly(3,4-ethyenedioxythiophene) (PEDOT) nanocomposites were prepared by an in-situ oxidative polymerization process. The electrical conductivity and Seebeck coefficient of the graphite/PEDOT nanocomposites with different content of graphite were measured in the temperature range from 300 K to 380 K. The results show that as the content of graphite increased from 0 to 37.2 wt %, the electrical conductivity of the nanocomposites increased sharply from 3.6 S/cm to 80.1 S/cm, while the Seebeck coefficient kept almost the same value (in the range between 12.0 μV/K to 15.1 μV/K) at 300 K, which lead to an increased power factor. The Seebeck coefficient of the nanocomposites increased from 300 K to 380 K, while the electrical conductivity did not substantially depend on the measurement temperature. As a result, a power factor of 3.2 μWm−1 K−2 at 380 K was obtained for the nanocomposites with 37.2 wt % graphite.

scholarly journals Effect of band structure adjustment based of Cu site on the thermoelectric properties of BiCuSeO

2021 ◽  
Author(s):  
Bo Feng
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Effective Mass ◽  
Valence Band ◽  
Thermoelectric Properties ◽  
Density Of States ◽  
First Principles Calculation ◽  
Temperature Range ◽  
Ti Doping

Abstract The effect of Ti doped at Cu site on the thermoelectric properties of BiCuSeO was studied by experimental method and first principles calculation. The results show that Ti doping can cause the lattice contraction and decrease the lattice constant. Ti doping can increase the band gap and lengthen the Cu/Ti-Se bond, resulting in the decrease of carrier concentration. Ti doping can reduce the effective mass and the Bi-Se bond length, correspondingly improve the carrier mobility. Ti doping can decrease the density of states of Cu-3d and Se-4p orbitals at the top of valence band, but Ti-4p orbitals can obviously increase the density of states at the top of valence band and finally increase the electrical conductivity in the whole temperature range. With the decrease of effective mass, Ti doping would reduce the Seebeck coefficient, but the gain effect caused by the increase of electrical conductivity is more than the benefit reduction effect caused by the decrease of Seebeck coefficient, and the power factor shows an upward trend. Ti doping can reduce Young's modulus, lead to the increase of defect scattering and strain field, correspondingly reduce the lattice thermal conductivity and total thermal conductivity. It is greatly increased for the ZT values in the middle and high temperature range, with the highest value of 1.04 at 873 K.

Thermoelectric Properties of n-type (Bi2Se3)x(Bi2Te3)1-x Crystals Prepared by Zone Melting

2008 ◽  
Vol 368-372 ◽  
pp. 547-549
Author(s):  
Jun Jiang ◽  
Ya Li Li ◽  
Gao Jie Xu ◽  
Ping Cui ◽  
Li Dong Chen
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Zone Melting ◽  
Chemical Compositions ◽  
Melting Method ◽  
Temperature Range

In the present study, n-type (Bi2Se3)x(Bi2Te3)1-x crystals with various chemical compositions were fabricated by the zone melting method. Thermoelectric properties, including Seebeck coefficient (α), electrical conductivity (σ) and thermal conductivity (κ), were measured in the temperature range of 300-500 K. The influence of the variations of Bi2Te3 and Bi2Se3 content on thermoelectric properties was studied. The increase of Bi2Se3 content (x) caused an increase in carrier concentration and thus an increase of σ and a decrease of α. The maximum figure of merit (ZT = α2σT/κ) of 0.87 was obtained at about 325 K for the composition of 93%Bi2Te3-7%Bi2Se3 with doping TeI4.

Effect of Thermal Treatment on Thermoelectric Properties of Extruded TiO2 Ceramics

2014 ◽  
Vol 604 ◽  
pp. 249-253 ◽  
Author(s):  
Agnese Pura ◽  
Janis Locs ◽  
Liga Berzina-Cimdina
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Thermal Treatment ◽  
Seebeck Coefficient ◽  
Heating Rate ◽  
Thermoelectric Properties ◽  
Sintering Temperature ◽  
Extrusion Process ◽  
Vacuum Heat Treatment ◽  
Treatment Conditions

TiO2samples were obtained by extrusion process, sintered in air at 1000 °C, 1100 °C, 1200°C and 1300 °C and, afterwards, thermally treated under vacuum conditions at 1250 °C for 1 hour applying two different heating/cooling rates (2 °C/min and 5 °C/min). It was found that thermal treatment conditions substantially affected thermoelectric properties of the samples. Increasing sintering temperature, during the sample thermal treatment in air, the electrical conductivity of the specimens increased, while Seebeck coefficient decreased. With an increase in the heating rate during the vacuum heat treatment of the samples, the electrical conductivity of the samples decreased, while Seebeck coefficient increased.

Sign in / Sign up

Export Citation Format

Share Document