scholarly journals Effect of Lubricating Phase on Microstructure and Properties of Cu–Fe Friction Materials

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 313 ◽  
Author(s):  
Xiaoyang Wang ◽  
Hongqiang Ru
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Carbon Black ◽  
Tribological Properties ◽  
Mass Fraction ◽  
Bending Strength ◽  
High Strength ◽  
Wear Loss ◽  
Powder Metallurgy Method ◽  
Friction Materials

Cu–Fe-based friction materials with flake graphite, granulated carbon black, and high-strength graphite as lubricating phase were prepared by the powder metallurgy method. The effects of different types and mass fraction of lubricating phase on the microstructure, mechanical properties, and tribological properties were investigated. The results show that when the mass fraction of granulated carbon black is 5 wt%, it is easy to form a good interface with the matrix, but the interface is prone to pores and cracks when its mass fraction is 10 wt%. The bending strength and compressive strength properties of the composites increased with increasing in the mass fraction of granulated carbon black and reached the maximum of 40 MPa and 70 MPa at 5 wt% granulated carbon black, after which bending strength and compressive strength all decreased. The friction coefficient and the wear loss of the materials initially decreased as the mass fraction of granulated carbon black increased and obtained minimum of 0.436 and 0.145 mm when the mass fraction of granulated carbon black was 5 wt%, then ascended. Compared with the sample with 5 wt% high-strength graphite as lubricating phase, the sample with 5 wt% granulated carbon black as lubricating phase had better sintering performance, mechanical properties, and tribological properties.

Fabrication and Mechanical Properties of Alumina—CNTs Composites

2011 ◽  
Vol 66-68 ◽  
pp. 1390-1396
Author(s):  
Jing Song Zhao ◽  
Yi Feng ◽  
Nan Nan Chen ◽  
Fan Yan Chen ◽  
Jie Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Powder Metallurgy ◽  
Nuclear Waste ◽  
Mass Fraction ◽  
Bending Strength ◽  
Waste Material ◽  
Powder Metallurgy Method ◽  
The Matrix

The transmutation target of nuclear waste material has been fabrication by a powder metallurgy method by using Alumina as the matrix and CNTs as reinforcement. The effect of different nanotube contents on the fracture toughness and the bending strength was investigation. The results showed the fracture toughness and the bending strength of composites increased with increasing CNTs mass fraction when the content of CNTs was less than 1.5%. However, when the contents of CNTs greater than 1.5%, the fracture toughness and the bending strength of composites decreased as the content of CNTs increased. Possible mechanisms are discussed in detail in the paper.

Mechanical properties of cured epoxy resin

2021 ◽  
Author(s):  
Sergey Savotchenko ◽  
Ekaterina Kovaleva
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Mass Fraction ◽  
Mechanical Characteristics ◽  
Bending Strength ◽  
The Impact ◽  
Impact Viscosity

We study experimentally the influence of mass fraction of L-20 hardener cold cure on mechanical properties of epoxy diane resin ED-20. We measure the hardness, tensile strength, bending strength and impact strength of resin at different values of the hardener mass fraction. It is found that the ratio hardener mass fraction of 1:0.9 leads to the highest values of the hardness, tensile strength, compressive strength and bending strength. The impact viscosity is maximum at the ratio hardener mass fraction of 1:0.8. The optimal ratio of a non-toxic safe hardener to the resin is derived based on obtained mechanical characteristics.

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

Deterioration of Mechanical Properties of High-Strength Pumpcrete after Exposure to High Temperatures

2010 ◽  
Vol 168-170 ◽  
pp. 564-569
Author(s):  
Guang Lin Yuan ◽  
Jing Wei Zhang ◽  
Jian Wen Chen ◽  
Dan Yu Zhu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Heating Rate ◽  
High Strength Concrete ◽  
Heating Temperature ◽  
High Strength ◽  
Air Cooling ◽  
Test Results ◽  
Strength Deterioration ◽  
Residual Compressive Strength

This paper makes an experimental study of mechanical properties of high-strength pumpcrete under fire, and the effects of heating rate, heating temperature and cooling mode on the residual compressive strength(RCS) of high-strength pumpcrete are investigated. The results show that under air cooling, the strength deterioration speed of high-strength concrete after high temperature increases with the increase of concrete strength grade. Also, the higher heating temperature is, the lower residual compressive strength value is. At the same heating rate (10°C/min), the residual compressive strength of C45 concrete after water cooling is a little higher than that after air cooling; but the test results are just the opposite for C55 and C65 concrete. The strength deterioration speed of high-strength concrete after high temperature increases with the increase of heating rate, but not in proportion. And when the heating temperature rises up between 200°C and 500°C, heating rate has the most remarkable effect on the residual compressive strength of concrete. These test results provide scientific proofs for further evaluation and analysis of mechanical properties of reinforced-concrete after exposure to high temperatures.

scholarly journals The Effect of Borax Solution as Preservative to the Mechanical Properties of Bamboo

2020 ◽  
Vol 11 (2) ◽  
Author(s):  
M.A.P Handana ◽  
◽  
Besman Surbakti ◽  
Rahmi Karolina ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Bending Strength ◽  
Environmentally Friendly ◽  
Preservative Solution ◽  
Borax Solution ◽  
Preservative Solutions

The use of borax solution as a preservative in wood and bamboo materials is well known in the community. A borax solution is an environmentally friendly liquid that can dissolve in water, so it is suitable to be used as a preservative within cold or hot soaking techniques. The ability of borax to resist insects and fungus attacks on bamboo has been proven, but the effect of the solution on the strength of bamboo must also be investigated. This study conducts to investigate the effects of borax and its additives as preservative solutions to the mechanical properties of bamboos. The bamboos preservations were conducted by cold conditions of immersion, while the mechanical properties were performed to understand the effects of preservatives. The result of this study indicated that 30% to 50% borax in the preservative solution is sufficient to provide significant increase in strength for compressive strength, tensile strength, and bending strength of bamboo specimen. From this study, the use of borax solution in preserving the bamboos materials improved the quality of bamboos based on its mechanical properties.

scholarly journals Effect of Locally Available Wheat Straw Ash in Developing High Strength Concrete

2021 ◽  
pp. 19-28
Author(s):  
Muhammad Armaghan Siffat ◽  
Muhammad Ishfaq ◽  
Afaq Ahmad ◽  
Khalil Ur Rehman ◽  
Fawad Ahmad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Wheat Straw ◽  
High Strength Concrete ◽  
High Strength ◽  
Optimum Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Strength Concrete ◽  
Straw Ash

This study is supervised to assess the characteristics of the locally available wheat straw ash (WSA) to consume as a substitute to the cement and support in enhancing the mechanical properties of concrete. Initially, after incineration at optimum temperature of 800°C for 0.5, the ash of wheat straw was made up to the desirable level of fineness by passing through it to the several grinding cycles. Subsequently, the X-ray fluorescence (XRF) along with X-ray diffraction (XRD) testing conducted on ash of wheat straw for the evaluation its pozzolanic potential. Finally, the specimens of concrete were made by consuming 10% and 20% percentages of wheat straw ash as a replacement in concrete to conclude its impact on the compressive strength of high strength concrete. The cylinders of steel of dimensions 10cm diameter x 20cm depth were acquired to evaluate the compressive strength of high strength concrete. The relative outcomes of cylinders made of wheat straw ash substitution presented the slight increase in strength values of the concrete. Ultimately, the C-100 blends and WSA aided cement blends were inspected for the rheology of WSA through FTIR spectroscopy along with Thermogravimetric technique. The conclusions authenticate the WSA potential to replace cement in the manufacturing of the high strength concrete.

scholarly journals Excellent Mechanical Properties of the Silicate Glasses Modified by CeO2 and TiO2: A New Choice for High-Strength and High-Modulus Glass Fibers

2021 ◽  
Author(s):  
Chao Chen ◽  
Qingong Zhu ◽  
Huanping Wang ◽  
Feifei Huang ◽  
Qinghua Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silicate Glass ◽  
Optical Fibers ◽  
Bending Strength ◽  
Glass Fibers ◽  
High Strength ◽  
Maximum Level ◽  
Compression Modulus ◽  
Co Doping ◽  
Optimum Approach

Abstract As is well known, silicate glass has a stable glass-forming region and mature drawing processes into fibers. In this study, to obtain enhanced mechanical properties, glasses with a composition of SiO2-Al2O3-MgO-CaO-B2O3-Fe2O3 were synthesized using TiO2 and CeO2. When the amount of TiO2 and CeO2 is less than 2 wt%, the mechanical properties increase with increases in the TiO2 and CeO2. However, as the amount of TiO2 and CeO2 increases from 2 to 3.5 wt%, the mechanical properties decrease. Co-doping with 1 wt% TiO2 and 1 wt% CeO2 was found to be the optimum approach, with a density, bending strength, compression strength, and compression modulus of 2.626 g/cm3, 108.36 MPa, 240.18 MPa, and 115.03 GPa, respectively. The optical band gap and Raman spectroscopy proved that, as long as the content of oxygen bonds reaches the maximum level, a kind of best structural stability and mechanical properties will be achieved. Hence, this type of high-strength silicate glass can be used in optical fibers for military defense, wind power generation, and transportation.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

scholarly journals Sintering of Ti-based biomedical alloys with increased oxygen content from elemental powders

2020 ◽  
Vol 321 ◽  
pp. 05010
Author(s):  
J. Stráský ◽  
J. Kozlík ◽  
K. Bartha ◽  
D. Preisler ◽  
T. Chráska
Keyword(s):  
Mechanical Properties ◽  
Oxygen Content ◽  
High Strength ◽  
Simple Approach ◽  
Fine Tuning ◽  
Powder Metallurgy Method ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Low Modulus

Revived interest for beta Ti alloys with increased oxygen content is motivated by the prospect of achieving material with low modulus and high strength simultaneously. Fine tuning of amount of oxygen and beta stabilizing elements is critical for achieving good mechanical properties. This study shows that powder metallurgy method of spark plasma sintering is capable of producing Ti-Nb-Zr-O alloys from elemental powders. This simple approach allows for quick sampling and production of several alloys with various chemical composition. Elemental powders were mixed with appropriate amount of titanium dioxide to achieve Ti-29Nb-7Zr-0.7O alloy. Sintering was performed at 1400 - 1500 °C for 15 – 30 minutes.

Sign in / Sign up

Export Citation Format

Share Document