scholarly journals Discrete Element Modeling of Intermetallic Matrix Composite Manufacturing by Powder Metallurgy

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 281 ◽  
Author(s):  
Szymon Nosewicz ◽  
Jerzy Rojek ◽  
Marcin Chmielewski ◽  
Katarzyna Pietrzak
Keyword(s):  
Powder Metallurgy ◽  
Numerical Model ◽  
Sintered Sample ◽  
Discrete Element ◽  
Adhesive Contact ◽  
Ceramic Composites ◽  
Numerical Representation ◽  
Discrete Element Modeling ◽  
Two Phase ◽  
Neck Size

This paper presents a numerical and experimental analysis of manufacturing of intermetallic ceramic composites by powder metallurgy techniques. The scope of the paper includes the formulation and development of an original numerical model of powder metallurgy of two-phase material within the framework of the discrete element method, simulations of powder metallurgy processes for different combinations of process parameters, and a verification of the numerical model based on own experimental results. Intermetallic-based composite NiAl–Al 2 O 3 has been selected as representative material for experimental and numerical studies in this investigation. Special emphasis was given to the interactions between the intermetallic and ceramic particles by formulating the special model for adhesive contact bond. In order to properly represent a real microstructure of a two-phase sintered body, a discrete element specimen was generated using a special algorithm. Numerical validation showed the correct numerical representation of a sintered two-phase composite specimen. Finally, micromechanical analysis was performed to explain the macroscopic behavior of the sintered sample. The evolution of the coordination number, a number of equilibrium contacts, and the distribution of the cohesive neck size with respect to time are presented.

Investigation of two-dimensional nonstationary processes of outflow a gas-saturated liquid from axisymmetric vessels

2012 ◽  
Vol 9 (1) ◽  
pp. 47-52
Author(s):  
R.Kh. Bolotnova ◽  
V.A. Buzina
Keyword(s):  
Comparative Analysis ◽  
Numerical Model ◽  
Liquid Mixture ◽  
Phase Model ◽  
Test Problems ◽  
Two Dimensional ◽  
Nonstationary Processes ◽  
Saturated Liquid ◽  
Two Phase ◽  
One Dimensional

The two-dimensional and two-phase model of the gas-liquid mixture is constructed. The validity of numerical model realization is justified by using a comparative analysis of test problems solution with one-dimensional calculations. The regularities of gas-saturated liquid outflow from axisymmetric vessels for different geometries are established.

scholarly journals An Energy-Based Discrete Element Modeling Method Coupled with Time-Series Analysis for Investigating Deformations and Failures of Jointed Rock Slopes

2021 ◽  
Vol 11 (12) ◽  
pp. 5447
Author(s):  
Xiaona Zhang ◽  
Gang Mei ◽  
Ning Xi ◽  
Ziyang Liu ◽  
Ruoshen Lin
Keyword(s):  
Time Series ◽  
Iterative Process ◽  
Discrete Element ◽  
Jointed Rock ◽  
Modeling Method ◽  
Discrete Element Modeling ◽  
Rock Slopes ◽  
Sliding Surface ◽  
Element Modeling ◽  
Displacement Based

The discrete element method (DEM) can be effectively used in investigations of the deformations and failures of jointed rock slopes. However, when to appropriately terminate the DEM iterative process is not clear. Recently, a displacement-based discrete element modeling method for jointed rock slopes was proposed to determine when the DEM iterative process is terminated, and it considers displacements that come from rock blocks located near the potential sliding surface that needs to be determined before the DEM modeling. In this paper, an energy-based discrete element modeling method combined with time-series analysis is proposed to investigate the deformations and failures of jointed rock slopes. The proposed method defines an energy-based criterion to determine when to terminate the DEM iterative process in analyzing the deformations and failures of jointed rock slopes. The novelty of the proposed energy-based method is that, it is more applicable than the displacement-based method because it does not need to determine the position of the potential sliding surface before DEM modeling. The proposed energy-based method is a generalized form of the displacement-based discrete element modeling method, and the proposed method considers not only the displacement of each block but also the weight of each block. Moreover, the computational cost of the proposed method is approximately the same as that of the displacement-based discrete element modeling method. To validate that the proposed energy-based method is effective, the proposed method is used to analyze a simple jointed rock slope; the result is compared to that achieved by using the displacement-based method, and the comparative results are basically consistent. The proposed energy-based method can be commonly used to analyze the deformations and failures of general rock slopes where it is difficult to determine the obvious potential sliding surface.

scholarly journals Experimental and Numerical Study on Water Filling and Air Expelling Process in a Pipe with Multiple Air Valves under Water Slow Filling Condition

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2511
Author(s):  
Jintao Liu ◽  
Di Xu ◽  
Shaohui Zhang ◽  
Meijian Bai
Keyword(s):  
Numerical Model ◽  
Stokes Equations ◽  
Numerical Study ◽  
Practical Method ◽  
Navier Stokes ◽  
Physical Processes ◽  
Two Phase ◽  
Saint Venant Equations ◽  
Water Filling ◽  
Air Valve

This paper investigates the physical processes involved in the water filling and air expelling process of a pipe with multiple air valves under water slow filling condition, and develops a fully coupledwater–air two-phase stratified numerical model for simulating the process. In this model, the Saint-Venant equations and the Vertical Average Navier–Stokes equations (VANS) are respectively applied to describe the water and air in pipe, and the air valve model is introduced into the VANS equations of air as the source term. The finite-volume method and implicit dual time-stepping method (IDTS) with two-order accuracy are simultaneously used to solve this numerical model to realize the full coupling between water and air movement. Then, the model is validated by using the experimental data of the pressure evolution in pipe and the air velocity evolution of air valves, which respectively characterize the water filling and air expelling process. The results show that the model performs well in capturing the physical processes, and a reasonable agreement is obtained between numerical and experimental results. This agreement demonstrates that the proposed model in this paper offers a practical method for simulating water filling and air expelling process in a pipe with multiple air valves under water slow filling condition.

Large-scale discrete element modeling in a fluidized bed

2010 ◽  
Vol 64 (10-12) ◽  
pp. 1319-1335 ◽  
Author(s):  
Mikio Sakai ◽  
Yoshinori Yamada ◽  
Yusuke Shigeto ◽  
Kazuya Shibata ◽  
Vanessa M. Kawasaki ◽  
...  
Keyword(s):  
Fluidized Bed ◽  
Large Scale ◽  
Discrete Element ◽  
Discrete Element Modeling ◽  
Element Modeling
Sign in / Sign up

Export Citation Format

Share Document