scholarly journals Compositional Dependence of Phase Selection in CoCrCu0.1FeMoNi-Based High-Entropy Alloys

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1290 ◽  
Author(s):  
Ning Liu ◽  
Chen Chen ◽  
Isaac Chang ◽  
Pengjie Zhou ◽  
Xiaojing Wang
Keyword(s):  
Molar Ratio ◽  
Mixing Enthalpy ◽  
High Entropy Alloy ◽  
Valence Electron Concentration ◽  
Face Centered Cubic ◽  
Distortion Parameter ◽  
Local Lattice Distortion ◽  
Phase Selection ◽  
High Entropy ◽  
Fcc Structure

To study the effect of alloy composition on phase selection in the CoCrCu0.1FeMoNi high-entropy alloy (HEA), Mo was partially replaced by Co, Cr, Fe, and Ni. The microstructures and phase selection behaviors of the CoCrCu0.1FeMoNi HEA system were investigated. Dendritic, inter-dendritic, and eutectic microstructures were observed in the as-solidified HEAs. A simple face centered cubic (FCC) single-phase solid solution was obtained when the molar ratio of Fe, Co, and Ni was increased to 1.7 at the expense of Mo, indicating that Fe, Co, and Ni stabilized the FCC structure. The FCC structure was favored at the atomic radius ratio δ ≤ 2.8, valence electron concentration (VEC) ≥ 8.27, mixing entropy ΔS ≤ 13.037, local lattice distortion parameter α2 ≤ 0.0051, and ΔS/δ2 > 1.7. Mixed FCC + body centered cubic (BCC) structures occurred for 4.1 ≤ δ ≤ 4.3 and 7.71 ≤ VEC ≤ 7.86; FCC or/and BCC + intermetallic (IM) mixtures were favored at 2.8 ≤ δ ≤ 4.1 or δ > 4.3 and 7.39 < VEC ≤ 8.27. The IM phase is favored at electronegativity differences greater than 0.133. However, ΔS, α2, and ΔS/δ2 were inefficient in identifying the (FCC or/and BCC + IM)/(FCC + BCC) transition. Moreover, the mixing enthalpy cannot predict phase structures in this system.

scholarly journals Microstructure and Mechanical Properties Investigation of the CoCrFeNiNbx High Entropy Alloy Coatings

Crystals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 409 ◽  
Author(s):  
Hui Jiang ◽  
Kaiming Han ◽  
Dayan Li ◽  
Zhiqiang Cao
Keyword(s):  
Wear Resistance ◽  
Steel Substrate ◽  
Alloy Coating ◽  
304 Stainless Steel ◽  
Molar Ratio ◽  
High Entropy Alloy ◽  
Solid Solution Phase ◽  
Face Centered Cubic ◽  
Laves Phases ◽  
High Entropy

In this work, the CoCrFeNiNbx (x: molar ratio, x = 0.45, 0.5, 0.75, and 1.0) high entropy alloy coatings were synthesized on a 304 stainless steel substrate by laser cladding to investigate the effect of Nb element on their microstructure, hardness, and wear resistance. The results indicated that in all of the CoCrFeNiNbx alloy coatings, two phases were found: One was a face-centered cubic (FCC) solid solution phase, the other was a Co1.92Nb1.08-type Laves phase. The microstructures of samples varied from hypoeutectic structure (x = 0.45 and 0.5) to hypereutectic structure (x = 0.75 and 1.0). The Vickers hardness of CoCrFeNiNbx alloy coatings was obviously improved compared with the substrate. The hardness value of the CoCrFeNiNb1.0 alloy coating reached to 590 HV, which was 2.8 times higher than that of the substrate. There was also a corresponding variation in wear properties with hardness evolutions. Wherein the hypereutectic CoCrFeNiNb1.0 alloy coating with the highest hardness exhibited the best wear resistance under the same wear condition, the dry wear test showed the wear mass loss of CoCrFeNiNb1.0 alloy coating was less than a third of the substrate. The high hardness and wear resistance properties were considered with the fine lamellar eutectic structure and proper combination of FCC and Laves phases.

Synthesis and Characterization of Novel High Entropy Alloys

2020 ◽  
Vol 978 ◽  
pp. 167-173
Author(s):  
Anil Kumar ◽  
B. Vinith ◽  
Aditya Kumar Choudhary ◽  
Manoj Kumar Chopkar
Keyword(s):  
Mechanical Alloying ◽  
Synthesis And Characterization ◽  
Mixing Enthalpy ◽  
Valence Electron Concentration ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Cubic Structure ◽  
Face Centered

High entropy alloys (HEAs) generally exhibit either high resistance to deformation or high toughness due to the presence of body-centered or face-centered cubic structure, respectively. To overcome these limitations, new high entropy alloys have been developed in the present study. This investigation aims to synthesis and characterization of novel CoCrFeNi3Si, CoCrFe2Ni2Si, and Co2CrFeNi2Si high entropy alloys. The mechanical alloying route is used to synthesize these alloys. Grinding was carried out to 20h and X-ray diffraction (XRD) analysis was done at different time intervals of grinding. The face-centered cubic structure along with the intermetallic compound of Ni-Si was observed after 20h of grinding. Furthermore, a pseudo binary strategy based on the valence electron concentration and mixing enthalpy is also employed to design the high entropy alloys considered in the present study. Carefully analysis of the XRD pattern indicates that from 5 to 20h of mechanical alloying there is a decrement in the initial peaks of elements observed.

scholarly journals Nanoporous Quasi-High-Entropy Alloy Microspheres

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 345 ◽  
Author(s):  
Lianzan Yang ◽  
Yongyan Li ◽  
Zhifeng Wang ◽  
Weimin Zhao ◽  
Chunling Qin
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Hierarchical Porous

High-entropy alloys (HEAs) present excellent mechanical properties. However, the exploitation of chemical properties of HEAs is far less than that of mechanical properties, which is mainly limited by the low specific surface area of HEAs synthesized by traditional methods. Thus, it is vital to develop new routes to fabricate HEAs with novel three-dimensional structures and a high specific surface area. Herein, we develop a facile approach to fabricate nanoporous noble metal quasi-HEA microspheres by melt-spinning and dealloying. The as-obtained nanoporous Cu30Au23Pt22Pd25 quasi-HEA microspheres present a hierarchical porous structure with a high specific surface area of 69.5 m2/g and a multiphase approximatively componential solid solution characteristic with a broad single-group face-centered cubic XRD pattern, which is different from the traditional single-phase or two-phase solid solution HEAs. To differentiate, these are named quasi-HEAs. The synthetic strategy proposed in this paper opens the door for the synthesis of porous quasi-HEAs related materials, and is expected to promote further applications of quasi-HEAs in various chemical fields.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

scholarly journals Microstructure Refinement by Low-Temperature Ausforming in an Fe-Based Metastable High-Entropy Alloy

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 742
Author(s):  
Motomichi Koyama ◽  
Takeaki Gondo ◽  
Kaneaki Tsuzaki
Keyword(s):  
Low Temperature ◽  
Plastic Anisotropy ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Microstructure Refinement ◽  
Hexagonal Close Packed ◽  
Solution Treated Condition ◽  
Solution Treated ◽  
Face Centered

The effects of ausforming in an Fe30Mn10Cr10Co high-entropy alloy on the microstructure, hardness, and plastic anisotropy were investigated. The alloy showed a dual-phase microstructure consisting of face-centered cubic (FCC) austenite and hexagonal close-packed (HCP) martensite in the as-solution-treated condition, and the finish temperature for the reverse transformation was below 200 °C. Therefore, low-temperature ausforming at 200 °C was achieved, which resulted in microstructure refinement and significantly increased the hardness. Furthermore, plasticity anisotropy, a common problem in HCP structures, was suppressed by the ausforming treatment. This, in turn, reduced the scatter of the hardness.

scholarly journals Influence of Aluminum and Molybdenum on the Microstructure and Corrosion Behavior of Thermally Sprayed High-Entropy Alloy Coatings

2021 ◽  
Author(s):  
Martin Löbel ◽  
Thomas Lindner ◽  
Maximilian Grimm ◽  
Lisa-Marie Rymer ◽  
Thomas Lampke
Keyword(s):  
Corrosion Resistance ◽  
Protective Coatings ◽  
Base Alloy ◽  
Alloy System ◽  
High Entropy Alloy ◽  
Oxide Content ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Structural And Functional Properties ◽  
Wide Range

AbstractHigh-entropy alloys (HEAs) have shown a wide range of promising structural and functional properties. By the application of coating technology, an economical exploitation can be achieved. The high wear and corrosion resistance of HEAs make them particularly interesting for the application as protective coatings. Especially for alloys with a high chromium content, a high corrosion resistance has been revealed. For the current investigations, the equimolar HEA CrFeCoNi with a single-phase face centered cubic structure is considered as a base alloy system. To increase the corrosion resistance as well as the hardness and strength, the influence of the alloying elements aluminum and molybdenum is analyzed. For the current investigations, the high kinetic process high-velocity oxygen fuel thermal spraying (HVOF) has been considered to produce coatings with a low porosity and oxide content. Feedstock is produced by inert gas atomization. The influence of the alloy composition on the microstructure, phase formation and resulting property profile is studied in detail. A detailed analysis of the corrosion resistance and underlying mechanisms is conducted. The pitting and passivation behavior are investigated by potentiodynamic polarization measurements in NaCl and H2SO4 electrolyte. A distinct improvement of the corrosion resistance can be achieved for the alloy Al0.3CrFeCoNiMo0.2.

scholarly journals Dynamic Mechanical Properties and Microstructure of an (Al0.5CoCrFeNi)0.95Mo0.025C0.025 High Entropy Alloy

Entropy ◽  
2019 ◽  
Vol 21 (12) ◽  
pp. 1154
Author(s):  
Bingfeng Wang ◽  
Chu Wang ◽  
Bin Liu ◽  
Xiaoyong Zhang
Keyword(s):  
Mechanical Properties ◽  
Shear Band ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Dynamic Mechanical Properties ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Dynamic Mechanical

The dynamic mechanical properties and microstructure of the (Al0.5CoCrFeNi)0.95Mo0.025C0.025 high entropy alloy (HEA) prepared by powder extrusion were investigated by a split Hopkinson pressure bar and electron probe microanalyzer and scanning electron microscope. The (Al0.5CoCrFeNi)0.95Mo0.025C0.025 HEA has a uniform face-centered cubic plus body-centered cubic solid solution structure and a fine grain-sized microstructure with a size of about 2 microns. The HEA possesses an excellent strain hardening rate and high strain rate sensitivity at a high strain rate. The Johnson–Cook plastic model was used to describe the dynamic flow behavior. Hat-shaped specimens with different nominal strain levels were used to investigate forced shear localization. After dynamic deformation, a thin and short shear band was generated in the designed shear zone and then the specimen quickly fractured along the shear band.

scholarly journals Cutting Edge of High-Entropy Alloy Superconductors from the Perspective of Materials Research

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1078
Author(s):  
Jiro Kitagawa ◽  
Shusuke Hamamoto ◽  
Naoki Ishizu
Keyword(s):  
Material Design ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
Simple Material ◽  
Σ Phase ◽  
High Entropy ◽  
Cscl Type ◽  
Materials Research ◽  
Face Centered ◽  
New Phenomena

High-entropy alloys (HEAs) are a new class of materials which are being energetically studied around the world. HEAs are characterized by a multicomponent alloy in which five or more elements randomly occupy a crystallographic site. The conventional HEA concept has developed into simple crystal structures such as face-centered-cubic (fcc), body-centered-cubic (bcc) and hexagonal-closed packing (hcp) structures. The highly atomic-disordered state produces many superior mechanical or thermal properties. Superconductivity has been one of the topics of focus in the field of HEAs since the discovery of the bcc HEA superconductor in 2014. A characteristic of superconductivity is robustness against atomic disorder or extremely high pressure. The materials research on HEA superconductors has just begun, and there are open possibilities for unexpectedly finding new phenomena. The present review updates the research status of HEA superconductors. We survey bcc and hcp HEA superconductors and discuss the simple material design. The concept of HEA is extended to materials possessing multiple crystallographic sites; thus, we also introduce multisite HEA superconductors with the CsCl-type, α-Mn-type, A15, NaCl-type, σ-phase and layered structures and discuss the materials research on multisite HEA superconductors. Finally, we present the new perspectives of eutectic HEA superconductors and gum metal HEA superconductors.

scholarly journals Phase Evolution and Microstructure Analysis of CoCrFeNiMo High-Entropy Alloy for Electro-Spark-Deposited Coatings for Geothermal Environment

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 406 ◽  
Author(s):  
Sigrun N. Karlsdottir ◽  
Laura E. Geambazu ◽  
Ioana Csaki ◽  
Andri I. Thorhallsson ◽  
Radu Stefanoiu ◽  
...  
Keyword(s):  
Bulk Material ◽  
Microstructural Analysis ◽  
Electrochemical Corrosion ◽  
High Hardness ◽  
Phase Evolution ◽  
Vacuum Arc ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
Σ Phase ◽  
High Entropy

In this work, a CoCrFeNiMo high-entropy alloy (HEA) material was prepared by the vacuum arc melting (VAM) method and used for electro-spark deposition (ESD). The purpose of this study was to investigate the phase evolution and microstructure of the CoCrFeNiMo HEA as as-cast and electro-spark-deposited (ESD) coating to assess its suitability for corrosvie environments encountered in geothermal energy production. The composition, morphology, and structure of the bulk material and the coating were analyzed using scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The hardness of the bulk material was measured to access the mechanical properties when preselecting the composition to be pursued for the ESD coating technique. For the same purpose, electrochemical corrosion tests were performed in a 3.5 wt.% NaCl solution on the bulk material. The results showed the VAM CoCrFeNiMo HEA material had high hardness (593 HV) and low corrosion rates (0.0072 mm/year), which is promising for the high wear and corrosion resistance needed in the harsh geothermal environment. The results from the phase evolution, chemical composition, and microstructural analysis showed an adherent and dense coating with the ESD technique, but with some variance in the distribution of elements in the coating. The crystal structure of the as-cast electrode CoCrFeNiMo material was identified as face centered cubic with XRD, but additional BCC and potentially σ phase was formed for the CoCrFeNiMo coating.

Sign in / Sign up

Export Citation Format

Share Document