scholarly journals Anisotropy of Transport Properties Correlated to Grain Boundary Density and Quantified Texture in Thick Oriented Ca3Co4O9 Ceramics

Materials ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1224 ◽  
Author(s):  
Driss Kenfaui ◽  
Moussa Gomina ◽  
Jacques Noudem ◽  
Daniel Chateigner
Keyword(s):  
Power Generation ◽  
High Temperature ◽  
Grain Boundary ◽  
Anisotropic Behavior ◽  
Boundary Density ◽  
Microstructural Parameters ◽  
Plasma Sintering ◽  
Marked Enhancement ◽  
Spark Plasma ◽  
The Mean

The misfit-layered Ca3Co4O9 oxide is being seen as a potential thermoelectric (TE) candidate for high-temperature power generation in air. Given the very small size and low strength exhibited by single crystals, grain-oriented Ca3Co4O9 ceramics are worth elaborating to capitalize on their anisotropy. However, the usual textured pellets are too thin to probe the TE properties along their principal crystallographic directions. In this paper, we report on the anisotropy of TE properties in the 350–860 K range within thick textured Ca3Co4O9 ceramics fabricated by moderately pressing at 1173 K stacks of pellets primarily textured using spark plasma sintering (SPS), spark plasma texturing (SPT), and hot pressing (HP). The texture was quantitatively assessed, and the influent microstructural parameters were identified, particularly the grain boundary density parallel (GBDc) and perpendicular (GBDab) to the mean c*-axis. We found that the edge-free processing fostered material texturing and (a,b) plane grain growth, thereby dropping GBDab and increasing GBDc. This resulted in a resistivity ρab reduction, leading to a marked enhancement in power factor PFab, which reached 520 μW·m−1·K−2 at 800 K for the HP sample. The anisotropy ρc/ρab was substantially promoted as the texture was reinforced and the GBDc/GBDab ratio increased, with ρc/ρab (HP) > ρc/ρab (SPT) > ρc/ρab (SPS). The Seebeck coefficient S also revealed an anisotropic behavior, with a ratio Sc/Sab >1 for the SPS-processed materials. This behavior was reversed (Sc/Sab <1) for the more textured SPT and HP specimens. It therefore resulted in a PF anisotropy PFc/PFab (HP) < PFc/PFab (SPT) < PFc/PFab (SPS). The PFab/PFc ratio attained 13.6 at 800 K for the thick HP sample, which is the largest ratio recorded thus far on undoped Ca3Co4O9 ceramics.

scholarly journals Fabrication and Characterization of Quinary High Entropy-Ultra-High Temperature Diborides

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 108-120
Author(s):  
Simone Barbarossa ◽  
Roberto Orrù ◽  
Valeria Cannillo ◽  
Antonio Iacomini ◽  
Sebastiano Garroni ◽  
...  
Keyword(s):  
High Temperature ◽  
Single Phase ◽  
Nominal Composition ◽  
High Entropy ◽  
Chemical Complexity ◽  
Alternative Processing ◽  
Plasma Sintering ◽  
High Temperature Synthesis ◽  
Spark Plasma

Due to their inherent chemical complexity and their refractory nature, the obtainment of highly dense and single-phase high entropy (HE) diborides represents a very hard target to achieve. In this framework, homogeneous (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2, (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2, and (Hf0.2Zr0.2Nb0.2Mo0.2Ti0.2)B2 ceramics with high relative densities (97.4, 96.5, and 98.2%, respectively) were successfully produced by spark plasma sintering (SPS) using powders prepared by self-propagating high-temperature synthesis (SHS). Although the latter technique did not lead to the complete conversion of initial precursors into the prescribed HE phases, such a goal was fully reached after SPS (1950 °C/20 min/20 MPa). The three HE products showed similar and, in some cases, even better mechanical properties compared to ceramics with the same nominal composition attained using alternative processing methods. Superior Vickers hardness and elastic modulus values were found for the (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2 and the (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2 systems, i.e., 28.1 GPa/538.5 GPa and 28.08 GPa/498.1 GPa, respectively, in spite of the correspondingly higher residual porosities (1.2 and 2.2 vol.%, respectively). In contrast, the third ceramic, not containing tantalum, displayed lower values of these two properties (25.1 GPa/404.5 GPa). However, the corresponding fracture toughness (8.84 MPa m1/2) was relatively higher. This fact can be likely ascribed to the smaller residual porosity (0.3 vol.%) of the sintered material.

scholarly journals Reduced Viscosity of Mg2GeO4 with Minor MgGeO3 between 1000 and 1150 °C Suggests Solid-State Lubrication at the Lithosphere–Asthenosphere Boundary

Minerals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 600
Author(s):  
Thomas Ferrand ◽  
Damien Deldicque
Keyword(s):  
Solid State ◽  
Grain Boundary ◽  
Metastable Phase ◽  
Viscosity Reduction ◽  
Tectonic Plates ◽  
Deformation Curves ◽  
Low Viscosity ◽  
Plasma Sintering ◽  
Stress Strain Relation ◽  
Spark Plasma

Tectonic plates are thought to move above the asthenosphere due to the presence of accumulated melts or volatiles that result in a low-viscosity layer, known as lithosphere–asthenosphere boundary (LAB). Here, we report experiments suggesting that the plates may slide through a solid-state mechanism. Ultrafine-grained aggregates of Mg2GeO4 and minor MgGeO3 were synthetized using spark plasma sintering (SPS) and deformed using a 1-atm deformation rig between 950 °C and 1250 °C. For 1000 < T < 1150 °C, the derivative of the stress–strain relation of the material drops down to zero once a critical stress as low as 30–100 MPa is reached. This viscosity reduction is followed by hardening. The deformation curves are consistent with what is commonly observed in steels during the shear-induced transformation from austenite to martensite, the final material being significantly harder. This is referred to as TRansformation-Induced Plasticity (TRIP), widely observed in metal alloys (TRIP alloys). It should be noted that such enhanced plasticity is not necessarily due to a phase transition, but could consist of any kind of transformation, including structural transformations. We suspect a stress-induced grain-boundary destabilization. This could be associated to the transient existence of a metastable phase forming in the vicinity of grain boundaries between 1000 and 1150 °C. However, no such phase can be observed in the recovered samples. Whatever its nature, the rheological transition seems to occur as a result of a competition between diffusional processes (i.e., thermally activated) and displacive processes (i.e., stress-induced and diffusionless). Consequently, the material would be harder at 1200 °C than at 1100 °C thanks to diffusion that would strengthen thermodynamically stable phases or grain-boundary structures. This alternative scenario for the LAB would not require volatiles. Instead, tectonic plates may slide on a layer in which the peridotite is constantly adjusting via a grain-boundary transformation.

High Temperature Corrosion Behavior of Si-Containing Alloys in the Gas Phase of Air-(Na2SO4+25.7mass%NaCl)

2011 ◽  
Vol 696 ◽  
pp. 272-277 ◽  
Author(s):  
Toto Sudiro ◽  
Tomonori Sano ◽  
Akira Yamauchi ◽  
Shoji Kyo ◽  
Osamu Ishibashi ◽  
...  
Keyword(s):  
High Temperature ◽  
Gas Phase ◽  
Corrosion Behavior ◽  
Elevated Temperatures ◽  
High Temperature Corrosion ◽  
Ni Content ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Corrosion Resistant Alloy ◽  
Si Content

The objective of this study is to develop an excellent corrosion resistant alloy for high temperature coating applications. The Si-containing alloys consisting of CoNiCrAlY and CrSi2 alloys with varying Si and Ni content respectively were prepared by spark plasma sintering (SPS) technique. The corrosion behavior of these alloys was investigated in the gas phase of air-(Na2SO4+25.7mass%NaCl) at elevated temperatures of 923, 1073 and 1273K. The results showed that CoNiCrAlY alloy with 30mass% Si content and CrSi2 alloy with 10mass% Ni content were the most effective materials for application in the gas phase of air-(Na2SO4+25.7mass%NaCl) due to the formation of protective Al2O3/SiO2 and SiO2 scale, respectively. Therefore, it is realized that CoNiCrAlY-30mass% Si and CrSi2-10mass% Si coating are very effective for improving of high temperature corrosion resistance of STBA21 steel.

Sign in / Sign up

Export Citation Format

Share Document