scholarly journals Selective Laser Sintering of PA6: Effect of Powder Recoating on Fibre Orientation

2020 ◽  
Vol 4 (3) ◽  
pp. 108
Author(s):  
Tobias Heckner ◽  
Michael Seitz ◽  
Sven Robert Raisch ◽  
Gerrit Huelder ◽  
Peter Middendorf
Keyword(s):  
Computed Tomography ◽  
Mechanical Properties ◽  
Layer Thickness ◽  
Laser Power ◽  
Laser Energy ◽  
Fibre Orientation ◽  
Selective Laser Sintering ◽  
Laser Sintering ◽  
Shear Stresses ◽  
Imaging Results

In Selective Laser Sintering, fibres are strongly orientated during the powder recoating process. This effect leads to an additional increase of anisotropy in the final printed parts. This study investigates the influence of process parameter variation on the mechanical properties and the fibre orientation. A full factorial design of experiment was created to evaluate the processing parameters of recoating speed, layer thickness and laser power on the part’s modulus of elasticity. Based on the mechanical testing, computed tomography was applied to selected samples to investigate the process-induced fibre microstructure, and calculate the fibre orientation tensors. The results show increasing part stiffness in the deposition direction, with decreasing layer thickness and increasing laser power, while the recoating speed only shows little effect on the mechanical performance. This complies with computed tomography imaging results, which show an increase in fibre orientation with smaller layer thickness. With thinner layers, and hence smaller shear gaps, shear stresses induced by the roller during recoating increase significantly, leading to excessive fibre reorientation and alignment. The high level of fibre alignment implies an increase of strength and stiffness in the recoating direction. In addition, thinner layer thickness under constant laser energy density results in improved melting behaviour, and thus improved fibre consolidation, consequently further increasing the mechanical properties. Meanwhile, the parameters of recoating speed and laser power do not have a significant impact on fibre orientation within their applicable process windows.

Research on Warpage of Polystyrene in Selective Laser Sintering

2010 ◽  
Vol 43 ◽  
pp. 578-582 ◽  
Author(s):  
C.Y. Wang ◽  
Q. Dong ◽  
X.X. Shen
Keyword(s):  
Layer Thickness ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Main Process ◽  
Influence Of Process Parameters ◽  
Temperature Changes ◽  
Hatch Spacing

Warpage is a crucial factor to accuracy of sintering part in selective laser sintering (SLS) process. In this paper, The influence of process parameters on warpage when sintering polystyrene(PS) materials in SLS are investigated. The laser power, scanning speed, hatch spacing, layer thickness as well as temperature of powder are considered as the main process parameters. The results showed that warpage increases with the increase of hatch space. Contary to it, warpage decreases with the increase of laser power. Warpage decreases with the increase of layer thickness between 0.16~0.18mm and changes little with increase of the thickness. Warpage increases along with the increase of scanning speed but decreases when the speed is over about 2000mm/s. When the temperature changes between 82°C-86°C, warpage decreases little with the increase of temperature. But further increase of temperature leads to warpage decreasing sharply when the temperature changes between 86°C-90°C.

Effects of the Processing Parameters on Porosity of Selective Laser Sintered Aliphatic Polycarbonate

2014 ◽  
Vol 915-916 ◽  
pp. 1000-1004 ◽  
Author(s):  
Xiao Hui Song ◽  
Yu Sheng Shi ◽  
Ping Hui Song ◽  
Qing Song Wei ◽  
Wei Li
Keyword(s):  
Mechanical Properties ◽  
Biomedical Engineering ◽  
Laser Power ◽  
Orthogonal Experiment ◽  
Selective Laser Sintering ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Optimal Parameters ◽  
Micro Structure ◽  
Aliphatic Polycarbonate

Selective Laser Sintering (SLS) has been successfully and broadly applied in biomedical engineering to fabricated biomedical part. And the porosity and microstructure of part can be controlled by main sintered parameters. This research focused aliphatic Polycarbonate (PC) sintered with SLS. According to the orthogonal experiment, the effect of laser power energy and interaction between main sintered parameters on porosity has been studied. Then the micro structure and mechanical properties of specimens sintered with the best optimal parameters have been analyzed.

scholarly journals Manufacturing of Porous Polycaprolactone Prepared with Different Particle Sizes and Infrared Laser Sintering Conditions: Microstructure and Mechanical Properties

2014 ◽  
Vol 6 ◽  
pp. 640496 ◽  
Author(s):  
G. V. Salmoria ◽  
D. Hotza ◽  
P. Klauss ◽  
L. A. Kanis ◽  
C. R. M. Roesler
Keyword(s):  
Mechanical Properties ◽  
Energy Density ◽  
Laser Energy ◽  
Flexural Modulus ◽  
Selective Laser Sintering ◽  
Polymeric Materials ◽  
Laser Sintering ◽  
Laser Energy Density ◽  
Particle Sizes ◽  
Mechanical Devices

The techniques of Rapid Prototyping, also known as Additive Manufacturing, have prompted research into methods of manufacturing polymeric materials with controlled porosity. This paper presents the characterization of the structure and mechanical properties of porous polycaprolactone (PCL) fabricated by Selective Laser Sintering (SLS) using two different particle sizes and laser processing conditions. The results of this study indicated that it is possible to control the microstructure, that is, pore size and degree of porosity, of the polycaprolactone matrix using the SLS technique, by varying the particle size and laser energy density, obtaining materials suitable for different applications, scaffolds and drug delivery and fluid mechanical devices. The specimens manufactured with smaller particles and higher laser energy density showed a higher degree of sintering, flexural modulus, and fatigue resistance when compared with the other specimens.

The Optimization Design Study of Selective Laser Sintering Process Parameters on the Pro-Coated Sand Mold

2011 ◽  
Vol 55-57 ◽  
pp. 853-858
Author(s):  
Rong Cheng ◽  
Xiao Yu Wu ◽  
Jian Ping Zheng
Keyword(s):  
Layer Thickness ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Dimensional Accuracy ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Process Variables ◽  
Scan Speed ◽  
Coated Sand

This paper presents experimental investigations on influence of important process parameters viz., laser power, scan speed, layer thickness, hatching space along with their interactions on dimensional accuracy of Selective Laser Sintering (SLS) processed pro-coated sand mold. It is observed that dimensional error is dominant along length and width direction of built mold. Optimum parameters setting to minimize percentage change in length and width of standard test specimen have been found out using Taguchi’s parameter design. Optimum process conditions are obtained by analysis of variance (ANOVA) is used to understand the significance of process variables affecting dimension accuracy. Scan speed and hatching space are found to be most significant process variables influencing the dimension accuracy in length and width. And laser power and layer thickness are less influence on the dimension accuracy. The optimum processing parameters are attained in this paper: laser power 11 W; scan speed 1200 mm/s; layer thickness 0.5 mm and hatching space 0.25 mm. It has been shown that, on average, the dimensional accuracy under this processing parameters combination could be improved by approximately up to 25% compared to other processing parameters combinations.

scholarly journals Emerging trend in manufacturing of 3D biomedical components using selective laser sintering: A review

2020 ◽  
Vol 184 ◽  
pp. 01047 ◽  
Author(s):  
Pankaj Kumar ◽  
Gazanfar Mustafa Ali syed
Keyword(s):  
Mechanical Properties ◽  
Laser Processing ◽  
Laser Power ◽  
Review Paper ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Sintering Process ◽  
Research Papers ◽  
Published Research

Additive manufacturing (also known as 3D printing) process is an emerging technique for the fabrication of biomedical components. Selective laser sintering or melting is one of the widely used additive printing technology for manufacturing of metallic and non-metallic components used in the industry. This review paper presents, a summary of the published research papers on the fabrication of biomedical components using selective laser sintering technique. Therefore, author meticulously attempted to investigate individual biocompatible material-wise review which includes Ti6Al4V, Ti-7.5 Mo alloy, β-Ti35Zr28Nb, PEEK, PA2200, and Polyamide/Hydroxyapatite. In addition, this article also explores the effects of the various laser sintering process parameters such as laser power, scanning speed, density of the material on the mechanical properties, tribological properties, porosity and surface roughness of the fabricated alloy. Moreover, the author also investigated challenges and future prospective of the laser processing of biomedical implants.

scholarly journals Effects of Fabrication Parameters on the Properties of Parts Manufactured with Selective Laser Sintering: Application on Cement-Filled PA12

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Abdelrasoul M. Gadelmoula ◽  
Saleh A. Aldahash
Keyword(s):  
Laser Power ◽  
Laser Energy ◽  
Selective Laser Sintering ◽  
Laser Sintering ◽  
Morphological Properties ◽  
Vector Length ◽  
Incident Laser Power ◽  
White Cement ◽  
Wide Range ◽  
Fabrication Parameters

Selective laser sintering (SLS) becomes a promising technology for manufacturing complicated objects with small to moderate numbers from a wide range of polymeric and metallic powders. However, the fabrication parameters in the SLS process need to be tailored for each end-use fabricated product. Hence, it becomes extremely important to investigate the effects of fabrication parameters on the mechanical and morphological properties of SLS parts. For this purpose, the present experimental work is devoted to evaluating the effects of some important fabrication parameters, that have not received proper attention in the published literature, on the properties of cement-filled polyamide 12 (PA12) parts manufactured with the SLS technique. The effect of scanning vector length on the tensile, compressive, and flexural strength of manufactured PA12/white cement parts is investigated. Also, the end-of-vector (EOV) effect on the edge geometry of manufactured parts is studied. Moreover, the effect of incident laser power (LP) on the surface quality of fabricated SLS PA12/white cement parts is qualitatively evaluated. The results from this work revealed that the scanning vector length significantly affects the mechanical properties of SLS parts provided that the load is applied along the scanning vector direction. Also, it is noticed that excessive exposure to laser energy at layer edges can deteriorate the part’s edge and in some cases can cause localized heating and burning of the part’s edge and, eventually, can result in surface microcracks. Finally, the experiments confirmed that increasing the laser power can enhance the surface roughness of manufactured parts; however, excessive increase in laser power causes localized burning and initiation of surface microcracks.

Orthotropic properties of cement-filled polyamide 12 manufactured by selective laser sintering

2020 ◽  
Vol 26 (6) ◽  
pp. 1103-1112
Author(s):  
Saleh Ahmed Aldahash ◽  
Abdelrasoul M. Gadelmoula
Keyword(s):  
Mechanical Properties ◽  
Laser Energy ◽  
Flexural Modulus ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Content Type ◽  
Build Orientation ◽  
Polyamide 12 ◽  
Fabrication Parameters

Purpose The cement-filled PA12 manufactured by selective laser sintering (SLS) offers desirable mechanical properties; however, these properties are dependent on several fabrication parameters. As a result, SLS prototypes may exhibit orthotropic mechanical properties unless properly oriented in build chamber. This paper aims to evaluate the effects of part build orientation, laser energy and cement content on mechanical properties of cement-filled PA12. Design/methodology/approach The test specimens were fabricated by SLS using the “DTM Sinterstation 2000” system at which the specimens were aligned along six different orientations. The scanning speed was 914mm/s, scan spacing was 0.15mm, layer thickness was 0.1mm and laser power was 4.5–8Watt. A total of 270 tensile specimens, 270 flexural specimens and 135 compression specimens were manufactured and the tensile, compression and flexural properties of fabricated specimens were evaluated. Findings The experiments revealed orientation-dependent (orthotropic) mechanical properties of SLS cement-filled PA12 and confirmed that the parts with shorter scan vectors have enhanced flexural strength as compared with longer scan vectors. The maximum deviations of ultimate tensile strength, compressive strength and flexural modulus along the six orientations were 32%, 26% and 36%, respectively. Originality/value Although part build orientation is a key fabrication parameter, very little was found in open literature with contradictory findings about its effect on mechanical properties of fabricated parts. In this work, the effects of build orientation when combined with other fabrication parameters on the properties of SLS parts were evaluated along six different orientations.

Sintering quality and parameters optimization of sisal fiber/PES composite fabricated by selective laser sintering (SLS)

2020 ◽  
pp. 089270572093917
Author(s):  
Aboubaker IB Idriss ◽  
Jian Li ◽  
Yanling Guo ◽  
Yangwei Wang ◽  
Xingdong Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Sisal Fiber ◽  
Optimum Parameters ◽  
Preheating Temperature

This article aims to improve the sintering quality of the sisal fiber/poly-(ether sulfone) (PES) composite (SFPC) part fabricated via selective laser sintering (SLS). The sisal fiber and PES powders were proposed as the feedstock of the SFPC powder bed for SLS. An orthogonal experimental methodology with four levels and five factors was applied to optimize the process parameters for the single-layer sintering experiment. The mechanical properties and accurate dimensions of the sintered part were tested using a universal testing machine and Vernier caliper. The preheating temperature, scanning speed, and laser power were selected as influencing factors on the mechanical properties and accuracy dimensions of the SFPC part. Furthermore, the influence factors on the quality of the sintered part were studied and analyzed. Additionally, the synthesis weighted scoring method was used to determine the optimum parameters of the SLS part. The results showed that the optimal parameters (factors) were preheating temperature of 82°C, scanning speed of 2 m s−1, laser power of 14 W, and laser wavelength of 10.6 μm. Thus, the quality of SFPC part was significantly enhanced when the optimum parameters were applied in SLS process. This article provided the main reference value for the choice of the process parameters of the biomass composite.

scholarly journals Bioactive Tetracalcium Phosphate Scaffolds Fabricated by Selective Laser Sintering for Bone Regeneration Applications

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2268 ◽  
Author(s):  
Tian Qin ◽  
Xiaoqian Li ◽  
Hui Long ◽  
Shizhen Bin ◽  
Yong Xu
Keyword(s):  
Mechanical Properties ◽  
Bone Regeneration ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Three Dimensional ◽  
Laser Sintering ◽  
Scaffold Material ◽  
Promising Candidate ◽  
Tetracalcium Phosphate ◽  
Good Biocompatibility

Tetracalcium phosphate (TTCP), a potential biological scaffold material, has attracted increasing interest for bone regeneration applications due to its good biodegradability and biocompatibility. In this research, three-dimensional porous TTCP scaffolds were manufactured via selective laser sintering (SLS), and an in-depth and meticulous study on the influence of laser power on the microstructure and mechanical properties of TTCP scaffolds was performed. The results showed that the TTCP particles fused together and formed a solid object due to the decrease in the number of micro-pores in the scaffold as the laser power increased from 6 W to 9 W. The maximum compressive strength that the scaffold could withstand and the strength of the fracture toughness were 11.87 ± 0.64 MPa and 1.12 ± 0.1 MPa·m1/2, respectively. When the laser power increased from 9 W to 10 W, the TTCP grains grew abnormally, resulting in diminished mechanical properties. The bioactivity tests showed that the surfaces of the scaffolds were entirely covered by bone-like apatite layers after soaking in simulated body fluid (SBF) for three days, indicating that the scaffolds exhibit excellent bioactivity. Moreover, cell experiments showed that the TTCP scaffolds had good biocompatibility. This study indicated that SLS-fabricated TTCP scaffolds may be a promising candidate for bone regeneration applications.

Sign in / Sign up

Export Citation Format

Share Document