scholarly journals Correlation of Rh Particle Size with CO Chemisorption: Effect on the Catalytic Oxidation of MTBE

2019 ◽  
Vol 3 (3) ◽  
pp. 81 ◽  
Author(s):  
Adrián Cervantes Uribe ◽  
Gloria Alicia Del Angel Montes ◽  
Gilberto Torres-Torres ◽  
Armando Vázquez-Zavala ◽  
Federico González-García ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Catalytic Oxidation ◽  
Oxidation Reaction ◽  
Methyl Tert Butyl Ether ◽  
Average Particle ◽  
Incipient Wetness Impregnation ◽  
Impregnation Method ◽  
Linear Interaction ◽  
Co Chemisorption

This study was conducted to identify the correlation between the CO chemisorption (linear interaction and gem dicarbonyl) and the specific size of rhodium particles, and further to determine the influence of this relationship on the catalytic oxidation reaction of methyl tert-butyl ether (MTBE). During the synthesis, first, TiO2 was developed by the sol-gel method under acidic conditions. Second, Rh was deposited (1 wt %) by the incipient wetness impregnation method. Later, with the aim of controlling the particle size, the Rh/TiO2 materials were crystallized at different reduction conditions during 3 h heat treatment. The results obtained by TEM micrographs indicated that the average particle size varies between 1.0 and 8.1 nm, depending on the conditions of heat treatment. From the histogram analysis of each TEM micrograph, two correlations were made: (i) the gem-dicarbonyl interaction was typical of Rh particles ≤ 1.5 nm, and (ii) a linear interaction, bridged interaction and dentate interaction were observed in particles ≥ 1.6 nm. The gem-dicarbonyl interaction (particle size ≤ 1.5 nm) was the most active in the oxidation reaction of MTBE.

scholarly journals Ordered intermetallic Pt–Cu nanoparticles for the catalytic CO oxidation reaction

RSC Advances ◽  
2016 ◽  
Vol 6 (88) ◽  
pp. 85634-85642 ◽  
Author(s):  
Govindachetty Saravanan ◽  
Rohini Khobragade ◽  
Laxmi Chand Nagar ◽  
Nitin Labhsetwar
Keyword(s):  
Particle Size ◽  
Co Oxidation ◽  
Oxidation Reaction ◽  
Average Particle Size ◽  
Pt Nanoparticles ◽  
Average Particle ◽  
Cu Nanoparticles ◽  
Catalytic Co Oxidation ◽  
Co Oxidation Reaction ◽  
Ordered Intermetallic

Intermetallic platinum (Pt) nanoparticles using the abundantly available element copper (Pt3Cu, PtCu, PtCu3) with an average particle size of 4–5 nm on a γ-Al2O3 support were prepared to reduce the consumption of Pt for the removal of CO from gases.

Manufacturing and Macroscopic Properties of Warm Sprayed Cu-36at.%In-15at.%Ga Coating Layer

2016 ◽  
Vol 705 ◽  
pp. 155-160
Author(s):  
Gi Su Ham ◽  
Hyung Jun Kim ◽  
Dae Hoon Ji ◽  
Kee Ahn Lee
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Coating Layer ◽  
Pure Aluminum ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Particle ◽  
Post Heat Treatment ◽  
Spray Process

A Cu-36at.%In-15at.%Ga coating layer is manufactured using a warm spray process and ternary alloy powders. The powder used had a particle-size distribution of 5~22μm with a spherical shape and average particle size of 11.6μm. Pure aluminum plate was used as a substrate. As a result, a CIG coating layer with 120μm thickness was successfully obtained. In order to improve the density of the coating layer, post heat treatment was applied for 1 hour in each condition of 200, 300 and 400°C. Phase analysis of the powder initially used identified Cu9In4, Cu9Ga4 phases, and Cu9In4, Cu9Ga4, Cu3Ga phases were identified after warm spraying. As heat treatment was applied, porosity decreased from 0.98% (as sprayed) to 0.8% (400°C), showing an increase in density, and hardness also decreased from 304Hv (as sprayed) to 258Hv (400°C).

Synthesis and Characterization of Bimetallic Fe/Co Nanocatalyst on CNTs for Fischer-Tropsch Reaction

2012 ◽  
Vol 16 ◽  
pp. 9-14 ◽  
Author(s):  
Sardar Ali ◽  
Noor Asmawati Mohd Zabidi ◽  
Duvvuri Subbarao
Keyword(s):  
Particle Size ◽  
Physicochemical Properties ◽  
Average Particle Size ◽  
Xrd Analysis ◽  
Synthesis And Characterization ◽  
Average Particle ◽  
Impregnation Method ◽  
Fischer Tropsch ◽  
Temperature Programmed

Cobalt and iron are common catalysts used in the Fischer-Tropsch (FT) reaction. This paper presents the synthesis and characterization of monometallic and bimetallic cobalt and iron nanoparticles supported on carbon nanotubes (CNTs). The CNTs-supported nanocatalysts were synthesized by a wet impregnation method at various ratios of Fe:Co. The physicochemical properties of the samples were analyzed by H2-temperature programmed reduction (TPR), CO and H2-chemisorption analyses, transmission electron microscopy (TEM) and X-ray diffraction (XRD) analysis. The effects of incorporation of Fe into Co on the physicochemical properties of Co/CNTs in terms of degree of reduction, CO and H2 chemisorptions and morphologies were investigated. TEM showed that metal nanoparticles were well dispersed on the external surface and inside the CNTs. For monometallic Co/CNTs and Fe/CNTs, the average metal particle size was 5±1 nm and 6±1 nm, respectively. For the bimetallic 70Co30Fe/CNTs nanocatalysts, the average particle size was found to be 4±1 nm. Metal particles attached to the outer walls were bigger than the ones inside the CNTs. H2-TPR analysis of Co/CNTs indicated two temperature regions at 330°C (low temperature) and 491°C (high temperature). The incorporation of iron into cobalt nanocatalysts of up to 30 % of the total metal loading enhanced the catalyst’s H2 and CO chemisorptions capacities and reducibility.

Preparation of Fe/SiO2 films by sputtering and their magnetic properties.

1995 ◽  
Vol 400 ◽  
Author(s):  
Tomoko Akai ◽  
Mitsuharu Tabuchi ◽  
Ryoji Funahashi ◽  
Hiroshi Yamanaka
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Particle Size ◽  
Magnetic Properties ◽  
Treatment Time ◽  
Average Particle Size ◽  
Heat Treating ◽  
Average Particle ◽  
Sio2 Films ◽  
Average Size

AbstractSiO2 thin films containing fine Fe particles were prepared by a co-sputtering method. α-Fe particles were then formed by heat-treating the film at 650°C to 700°C. The average size of the particles was controlled by changing heat-treatment time and temperature. The magnetic properties of these samples were investigated and discussed in terms of the size of the particles. It was found that the coercivity of the sample containing α-Fe particles (average particle size = 24nm) is as large as 36 Oe which is much higher than that of the bulk Fe.

Determination of grinding parameters of fenugreek seed

1970 ◽  
Vol 26 (1) ◽  
pp. 16 ◽  
Author(s):  
S Balasubramanian ◽  
Rajkumar Rajkumar ◽  
K K Singh
Keyword(s):  
Particle Size ◽  
Energy Consumption ◽  
Moisture Content ◽  
Specific Energy ◽  
Feed Rate ◽  
Average Particle Size ◽  
Specific Energy Consumption ◽  
Average Particle ◽  
Fenugreek Seeds ◽  
Fenugreek Seed

Experiment to identify ambient grinding conditions and energy consumed was conducted for fenugreek. Fenugreek seeds at three moisture content (5.1%, 11.5% and 17.3%, d.b.) were ground using a micro pulverizer hammer mill with different grinding screen openings (0.5, 1.0 and 1.5 mm) and feed rate (8, 16 and 24 kg h-1) at 3000 rpm. Physical properties of fenugreek seeds were also determined. Specific energy consumptions were found to decrease from 204.67 to 23.09 kJ kg-1 for increasing levels of feed rate and grinder screen openings. On the other hand specific energy consumption increased with increasing moisture content. The highest specific energy consumption was recorded for 17.3% moisture content and 8 kg h-1 feed rate with 0.5 mm screen opening. Average particle size decreased from 1.06 to 0.39 mm with increase of moisture content and grinder screen opening. It has been observed that the average particle size was minimum at 0.5 mm screen opening and 8 kg h-1 feed rate at lower moisture content. Bond’s work index and Kick’s constant were found to increase from 8.97 to 950.92 kWh kg-1 and 0.932 to 78.851 kWh kg-1 with the increase of moisture content, feed rate and grinder screen opening, respectively. Size reduction ratio and grinding effectiveness of fenugreek seed were found to decrease from 4.11 to 1.61 and 0.0118 to 0.0018 with the increase of moisture content, feed rate and grinder screen opening, respectively. The loose and compact bulk densities varied from 219.2 to 719.4 kg m-3 and 137.3 to 736.2 kg m-3, respectively.  

Formulating SLN and NLC as Innovative Drug Delivery Systems for Non-Invasive Routes of Drug Administration

2020 ◽  
Vol 27 (22) ◽  
pp. 3623-3656 ◽  
Author(s):  
Bruno Fonseca-Santos ◽  
Patrícia Bento Silva ◽  
Roberta Balansin Rigon ◽  
Mariana Rillo Sato ◽  
Marlus Chorilli
Keyword(s):  
Drug Delivery ◽  
Particle Size ◽  
Drug Release ◽  
Drug Loading ◽  
Average Particle Size ◽  
Delivery Systems ◽  
Average Particle ◽  
Minor Importance ◽  
Routes Of Administration ◽  
Non Invasive

Colloidal carriers diverge depending on their composition, ability to incorporate drugs and applicability, but the common feature is the small average particle size. Among the carriers with the potential nanostructured drug delivery application there are SLN and NLC. These nanostructured systems consist of complex lipids and highly purified mixtures of glycerides having varying particle size. Also, these systems have shown physical stability, protection capacity of unstable drugs, release control ability, excellent tolerability, possibility of vectorization, and no reported production problems related to large-scale. Several production procedures can be applied to achieve high association efficiency between the bioactive and the carrier, depending on the physicochemical properties of both, as well as on the production procedure applied. The whole set of unique advantages such as enhanced drug loading capacity, prevention of drug expulsion, leads to more flexibility for modulation of drug release and makes Lipid-based nanocarriers (LNCs) versatile delivery system for various routes of administration. The route of administration has a significant impact on the therapeutic outcome of a drug. Thus, the non-invasive routes, which were of minor importance as parts of drug delivery in the past, have assumed added importance drugs, proteins, peptides and biopharmaceuticals drug delivery and these include nasal, buccal, vaginal and transdermal routes. The objective of this paper is to present the state of the art concerning the application of the lipid nanocarriers designated for non-invasive routes of administration. In this manner, this review presents an innovative technological platform to develop nanostructured delivery systems with great versatility of application in non-invasive routes of administration and targeting drug release.

Azithromycin nanosuspension preparation using evaporative precipitation into aqueous solution (EPAS) method and its comparative dissolution study

2020 ◽  
Vol 17 ◽  
Author(s):  
Mohammad Hossain Shariare ◽  
Tonmoy Kumar Mondal ◽  
Hani Alothaid ◽  
Md. Didaruzzaman Sohel ◽  
MD Wadud ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Dissolution Rate ◽  
Average Particle Size ◽  
Scale Up ◽  
Average Particle ◽  
Total Drug ◽  
Residual Solvent ◽  
Dissolution Study ◽  
Drug Content

Aim: EPAS (evaporative precipitation into aqueous solution) was used in the current studies to prepare azithromycin nanosuspensions and investigate the physicochemical characteristics for the nanosuspension batches with the aim of enhancing the dissolution rate of the nanopreparation to improve bioavailability. Methods: EPAS method used in this study for preparing azithromycin nanosuspension was achieved through developing an in-house instrumentation method. Particle size distribution was measured using Zetasizer Nano S without sample dilution. Dissolved azithromycin nanosuspensions were also compared with raw azithromycin powder and commercially available products. Total drug content of nanosuspension batches were measured using an Ultra-Performance Liquid Chromatography (UPLC) system with Photodiode Array (PDA) detector while residual solvent was measured using gas chromatography (GC). Results: The average particle size of azithromycin nanosuspension was 447.2 nm and total drug content was measured to be 97.81% upon recovery. Dissolution study data showed significant increase in dissolution rate for nanosuspension batch when compared to raw azithromycin and commercial version (microsuspension). The residual solvent found for azithromycin nanosuspension is 0.000098023 mg/ mL or 98.023 ppb. Conclusion: EPAS was successfully used to prepare azithromycin nanoparticles that exhibited significantly enhanced dissolution rate. Further studies are required to scale up the process and determine long term stability of the nanoparticles.

scholarly journals A Thermally Conductive Pt/AAO Catalyst for Hydrogen Passive Autocatalytic Recombination

Catalysts ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 491
Author(s):  
Alina E. Kozhukhova ◽  
Stephanus P. du Preez ◽  
Aleksander A. Malakhov ◽  
Dmitri G. Bessarabov
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Combustion Temperature ◽  
Volume Fraction ◽  
Morphological Characteristics ◽  
Al Alloy ◽  
Impregnation Method ◽  
Case Scenario ◽  
Worst Case ◽  
Thermal Distribution

In this study, a Pt/anodized aluminum oxide (AAO) catalyst was prepared by the anodization of an Al alloy (Al6082, 97.5% Al), followed by the incorporation of Pt via an incipient wet impregnation method. Then, the Pt/AAO catalyst was evaluated for autocatalytic hydrogen recombination. The Pt/AAO catalyst’s morphological characteristics were determined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The average Pt particle size was determined to be 3.0 ± 0.6 nm. This Pt/AAO catalyst was tested for the combustion of lean hydrogen (0.5–4 vol% H2 in the air) in a recombiner section testing station. The thermal distribution throughout the catalytic surface was investigated at 3 vol% hydrogen (H2) using an infrared camera. The Al/AAO system had a high thermal conductivity, which prevents the formation of hotspots (areas where localized surface temperature is higher than an average temperature across the entire catalyst surface). In turn, the Pt stability was enhanced during catalytic hydrogen combustion (CHC). A temperature gradient over 70 mm of the Pt/AAO catalyst was 23 °C and 42 °C for catalysts with uniform and nonuniform (worst-case scenario) Pt distributions. The commercial computational fluid dynamics (CFD) code STAR-CCM+ was used to compare the experimentally observed and numerically simulated thermal distribution of the Pt/AAO catalyst. The effect of the initial H2 volume fraction on the combustion temperature and conversion of H2 was investigated. The activation energy for CHC on the Pt/AAO catalyst was 19.2 kJ/mol. Prolonged CHC was performed to assess the durability (reactive metal stability and catalytic activity) of the Pt/AAO catalyst. A stable combustion temperature of 162.8 ± 8.0 °C was maintained over 530 h of CHC. To confirm that Pt aggregation was avoided, the Pt particle size and distribution were determined by TEM before and after prolonged CHC.

scholarly journals Evaluation of the Effects of Filler Fineness on the Properties of an Epoxy Asphalt Mixture

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2003
Author(s):  
Wei Xu ◽  
Jintao Wei ◽  
Zhengxiong Chen ◽  
Feng Wang ◽  
Jian Zhao
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
Asphalt Mixture ◽  
Average Particle ◽  
Fine Dust ◽  
Bonding Structure ◽  
Epoxy Asphalt ◽  
Mineral Powder ◽  
Marshall Stability ◽  
Mixture Sample

The type and fineness of a filler significantly affect the performance of an asphalt mixture. There is a lack of specific research on the effects of filler fineness and dust from aggregates on the properties of epoxy asphalt (EA) mixtures. The effects of aggregate dust and mineral powder on the properties of an EA mixture were evaluated. These filler were tested to determine their fineness, specific surface area and mineral composition. The effects of these fillers on the EA mastic sample and mixture were evaluated. The morphology of the EA mastic samples was analyzed using scanning electron microscopy (SEM). The effects of the fillers on the Marshall stability, tensile strength and fatigue performance of the EA mixture were evaluated. The dust from the aggregates exhibited an even particle size distribution, and its average particle size was approximately 20% of that of the mineral powder. The SEM microanalysis showed that the EA mastic sample containing relatively fine dust formed a tight and dense interfacial bonding structure with the aggregate. The EA mixture sample containing filler composed of dust from aggregate had a significantly higher strength and longer fatigue life than that of the EA sample containing filler composed of mineral powder.

Sign in / Sign up

Export Citation Format

Share Document