scholarly journals Evaluation of Critical Parameters in Tensile Strength Measurement of Single Fibres

2019 ◽  
Vol 3 (3) ◽  
pp. 69 ◽  
Author(s):  
Faisal Islam ◽  
Sébastien Joannès ◽  
Lucien Laiarinandrasana
Keyword(s):  
Sensitivity Analysis ◽  
Tensile Strength ◽  
Composite Materials ◽  
Measurement Errors ◽  
Single Fibre ◽  
Critical Parameters ◽  
Fibre Strength ◽  
Relative Significance ◽  
Fibre Properties ◽  
Small Gauge

Mechanical properties of fibre reinforced composites are primarily dependent on those of fibres. Fibre properties are used for estimating the damage and strength behaviour of composite materials and structures. Tensile strength of fibres is commonly determined by single fibre tensile tests, which is challenging and is prone to measurement errors. In this study, different possible sources of errors due to experimental limitations in the fibre testing process were identified. Their effect on fibre tensile strength was analytically modelled. This model was used to evaluate the uncertainty in experimentally determined fibre strength. A sensitivity analysis was conducted to rank the relative significance of input quantities on the calculated fibre strength. Since composite models require fibre properties determined at very small gauge lengths, the results of the sensitivity analysis were extrapolated to determine critical parameters for tests done at those small gauge lengths of a few millimetres. It was shown that, for sufficiently long fibres, their strength depends mainly on the diameter and failure force; however, for shorter gauge lengths, the effects of misalignment become very significant. The knowledge of uncertainty would be useful in estimating the reliability of the predictions made by composite strength models on the damage and failure behaviour of composite materials and structures. Minimising the influence of critical parameters on fibre strength would help in designing improved single fibre testing systems capable of determining fibre strength more accurately.

A comparison of fibre deformations from mill like and laboratory kraft cooking of softwood

2014 ◽  
Vol 29 (2) ◽  
pp. 211-217
Author(s):  
Lennart Salmén ◽  
Joanna Hornatowska
Keyword(s):  
Tensile Strength ◽  
Unsolved Problem ◽  
The Other ◽  
Fibre Strength ◽  
Mechanical Forces ◽  
Lower Strength ◽  
Fibre Properties ◽  
Kraft Cooking ◽  
Pulp Strength ◽  
Fibre Shape

Abstract The fact that industrial pulps have a lower strength than their corresponding laboratory pulps is an unsolved problem affecting in various ways the potential fibre utilisation in different mills. The loss of pulp strength has to a great extent been attributed to changes at the fibre level. In order to clarify in what way changes in fibre properties contribute to the strength losses, cooking experiments were conducted using a laboratory batch digester in which mechanical forces may be introduced. Fibre properties, i.e. fibre structure and fibre strength, of laboratory-made pulps were compared with those of an industrial pulp. It was concluded that two essentially different mechanisms may be identified; one related to the transverse fibre shape, the other to fibre damage. The latter is manifested as lower rewetted zero-span strength which reduces tear resistance and tensile strength of the pulp. The former is a collapse of the fibre, reducing the lumen area and resulting in a pulp with lower water-retaining capacity, given sheets of lower density and a pulp that has to be beaten to a higher degree to reach the desired bonding and the desired tensile strength.

Single fibre strength of cellulosic fibre extracted from “Belatlan roots” plant

2017 ◽  
Author(s):  
M. Hanis. A. H. ◽  
M. S. Abdul Majid ◽  
M. J. M. Ridzuan ◽  
I. Fahmi
Keyword(s):  
Single Fibre ◽  
Fibre Strength ◽  
Cellulosic Fibre

Effect of Heat Setting Methods on Structures and Properties of High Strength Polyvinyl Alcohol Fibre

2015 ◽  
Vol 815 ◽  
pp. 643-648
Author(s):  
Yin Zhu ◽  
Jiong Xin Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Setting Time ◽  
High Strength ◽  
Single Fibre ◽  
X Ray Diffraction ◽  
Heat Setting ◽  
Heat Treated ◽  
Setting Process

The effect of heat setting methods on the structures and mechanical properties of high strength polyvinyl alcohol (PVA) fibre is studied in this article. The microstructure and mechanical properties of heat treated PVA fibre is investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and single fibre electronic tensile strength tester. Results show that the heat setting method with constant tension is a good heat setting method which can largely enhance the tensile strength of PVA fibre. During the heat setting process, the mechanical properties of PVA fibre are greatly affected by the temperature, tension and setting time. When the temperature is 220°C, tension is 5cN/dtex and setting time is 90sec, the tensile strength of PVA fibre increases from 12.0cN/dtex to 16.4cN/dtex in compare with the PVA fibre without heat setting

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Reuse of polyester-glass laminate waste in polymer composites

2021 ◽  
Vol 2 (107) ◽  
pp. 49-58
Author(s):  
M. Chomiak
Keyword(s):  
Tensile Strength ◽  
Composite Materials ◽  
Impact Strength ◽  
Volume Fraction ◽  
Matrix Composites ◽  
Glass Laminate ◽  
The Sustainable Development ◽  
Processing Properties ◽  
New Generation ◽  
Practical Implications

Purpose: of this paper is to develop a new generation of polymer composite materials that would ensure the use of residual and serious environmental problems of polyester-glass laminate waste. Design/methodology/approach: The glass reinforced polyester waste was ground and added to produce new composites. Thermoplastic - high impact polystyrene was selected for the composite matrix. Composites containing 10, 20, 30% by weight of the filler of polyester-glass laminate powder were made. The process of extrusion and subsequent injection was used to prepare the test samples. The influence of the filler on selected properties of composites was evaluated. The physical properties of the filler as well as the processing properties of the mixture as well as the mechanical properties - impact strength and tensile strength of the obtained composites were investigated. Findings: A decrease in tensile strength and impact strength was observed along with an increase in the amount of filler. Research limitations/implications: It would be interesting to carry out further analyzes, in particular with a higher volume fraction of the filler or with a different composite structure, e.g. using PVC as a matrix. The developed research topic is a good material for the preparation of publications of a practical and scientific nature, especially useful in the research and industrial environment. Practical implications: The shredded glass-polyester waste can be used as a filler of polystyrene, however, the resulting composite could be used to produce parts with slightly less responsible functions such as artificial jewelery or toy elements. Originality/value: Obtained results are a new solution a global waste management solution for glass reinforced polyester waste, which may contribute to the sustainable development of the composite materials industry through the partial utilization of waste composites with a duroplastic matrix.

Fibre deformations induced by different mechanical treatments and their effect on zero-span strength

2012 ◽  
Vol 27 (2) ◽  
pp. 335-342 ◽  
Author(s):  
Xiling Zeng ◽  
Shiyu Fu ◽  
Elias Retulainen ◽  
Sabine Heinemann
Keyword(s):  
Tensile Strength ◽  
Mechanical Treatment ◽  
Kraft Pulp ◽  
Fibre Surface ◽  
Wall Structure ◽  
Fibre Strength ◽  
Different Types ◽  
Chemical Conditions ◽  
Mechanical Devices ◽  
High Consistency

Abstract Fibre deformations have a significant effect on fibre strength and sheet properties. There is little information, however, on the kinds of deformations different types of treatments induce and how they affect the fibre strength. In the present study, first-thinning bleached pine kraft pulp was treated with three mechanical devices: a wing defibrator (high consistency treatment), an E-compactor (high consistency treatment) and a conventional Valley beater (low consistency treatment). The fibre properties were determined with a fibre analyser. The fibre cutting induced by the hydrochloric acid (HCl) treatment (‘cleavage index’) was used for the quantification of the fibre defects. The zero-span tensile strength of dry and wet paper was used to estimate the fibre strength. Each mechanical treatment induced fibre deformations in its own characteristic way. The wing defibrator induced fibre kinks and curl whereas the E-compactor, in addition to fibre cutting, favoured kinks. Low consistency Valley beating straightened the fibres and released fibre deformations. The fibre deformations, especially the number of kinks, correlated well with the wet zero-span tensile strength. The cleavage index had some correlation with the zero-span tensile strength, but the results indicated that the cleavage index may not be directly related to the mechanical defects in fibres but depend more on the chemical conditions on the fibre surface and the wall structure.

Co-milling-assisted exfoliated graphite nanoplatelets filler introduction in polyethylene and alumina composites

2018 ◽  
Vol 53 (13) ◽  
pp. 1815-1826
Author(s):  
Sheng Cai Tan ◽  
Jimmy KW Chan ◽  
Kian Ping Loh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Exfoliated Graphite ◽  
Flexural Properties ◽  
Graphite Nanoplatelets ◽  
Alumina Composites ◽  
Exfoliated Graphite Nanoplatelets ◽  
Polyethylene Composites

This paper aims to investigate the effect of co-milling-assisted exfoliation of graphite into polyethylene and alumina matrices on the mechanical properties of the composites. Tensile mechanical properties of composite materials based on polyethylene reinforced with graphite and graphite-derived fillers at 0–0.75 wt% loading were investigated, while hardness and flexural properties of alumina composites with 0.25 wt% loading of the same additives were assessed. Exfoliated graphite, applied at 0.25–0.75 wt% in pre-exfoliated form or in a co-milling-assisted fashion, has been demonstrated to be effective in enhancing the tensile strength of polyethylene composites. Similar enhancement in hardness and flexural properties was observed in alumina composites with 0.25 wt% loading of the exfoliated graphite. Co-milling-assisted exfoliated graphite nanoplatelets additive introduction has been found to effect a more desirable mechanical properties enhancement in the composites investigated in this study.

Sign in / Sign up

Export Citation Format

Share Document