scholarly journals Optimization of Fiber Orientation Model Parameters in the Presence of Flow-Fiber Coupling

2018 ◽  
Vol 2 (4) ◽  
pp. 73 ◽  
Author(s):  
Tianyi Li ◽  
Jean-François Luyé

In this paper, we propose a novel systematic procedure to minimize the discrepancy between the numerically predicted and the experimentally measured fiber orientation results on an injection-molded part. Fiber orientation model parameters are optimized simultaneously using Latin hypercube sampling and kriging-based adaptive surrogate modeling techniques. Via an adequate discrepancy measure, the optimized solution possesses correct skin–shell–core structure and global orientation evolution throughout the considered center-gated disk. Some non-trivial interaction between these parameters and flow-fiber coupling effects as well as their quantitative importance are illustrated. The parametric fine-tuning of orientation models mostly leads to a better agreement in the skin and shell regions, while the coupling effect via a fiber-dependent viscosity improves prediction in the core.

2017 ◽  
Vol 29 (12) ◽  
pp. 121608 ◽  
Author(s):  
Gregory Lambert ◽  
Peter Wapperom ◽  
Donald Baird

2020 ◽  
Vol 4 (4) ◽  
pp. 163
Author(s):  
Fabian Willems ◽  
Philip Reitinger ◽  
Christian Bonten

Short fiber reinforced thermoplastics (SFT) are extensively used due to their excellent mechanical properties and low processing costs. Long fiber reinforced thermoplastics (LFT) show an even more interesting property profile and are increasingly used for structural parts. However, their processing by injection molding is not as simple as for SFT, and their anisotropic properties resulting from the fiber microstructure (fiber orientation, length, and concentration) pose a challenge with regard to the engineering design process. To reliably predict the structural mechanical properties of fiber reinforced thermoplastics by means of micromechanical models, it is also necessary to reliable predict the fiber microstructure. Therefore, it is crucial to calibrate the underlying prediction models, such as the fiber orientation model, within the process simulation. In general, these models may be adjusted manually, but this is usually ineffective and time-consuming. To overcome this challenge, a new calibration method was developed to automatically calibrate the fiber orientation model parameters of the injection molding simulation by means of optimization methods. This optimization routine is based on experimentally determined fiber orientation distributions and leads to optimized parameters for the fiber orientation prediction model within a few minutes. To better understand the influence of the model parameters, different versions of the fiber orientation model, as well as process and material influences on the resulting fiber orientation distribution, were investigated. Finally, the developed approach to calibrate the fiber orientation model was compared with a classical approach, a direct optimization of the whole process simulation. Thereby, the new optimization approach shows a calculation time reduced by the factor 15 with comparable error variance.


Kerntechnik ◽  
2021 ◽  
Vol 86 (2) ◽  
pp. 152-163
Author(s):  
T.-C. Wang ◽  
M. Lee

Abstract In the present study, a methodology is developed to quantify the uncertainties of special model parameters of the integral severe accident analysis code MAAP5. Here, the in-vessel hydrogen production during a core melt accident for Lungmen Nuclear Power Station of Taiwan Power Company, an advanced boiling water reactor, is analyzed. Sensitivity studies are performed to identify those parameters with an impact on the output parameter. For this, multiple calculations of MAAP5 are performed with input combinations generated from Latin Hypercube Sampling (LHS). The results are analyzed to determine the 95th percentile with 95% confidence level value of the amount of in-vessel hydrogen production. The calculations show that the default model options for IOXIDE and FGBYPA are recommended. The Pearson Correlation Coefficient (PCC) was used to determine the impact of model parameters on the target output parameters and showed that the three parameters TCLMAX, FCO, FOXBJ are highly influencing the in-vessel hydrogen generation. Suggestions of values of these three parameters are given.


2018 ◽  
Vol 15 (9) ◽  
pp. 2909-2930 ◽  
Author(s):  
Sebastian Lienert ◽  
Fortunat Joos

Abstract. A dynamic global vegetation model (DGVM) is applied in a probabilistic framework and benchmarking system to constrain uncertain model parameters by observations and to quantify carbon emissions from land-use and land-cover change (LULCC). Processes featured in DGVMs include parameters which are prone to substantial uncertainty. To cope with these uncertainties Latin hypercube sampling (LHS) is used to create a 1000-member perturbed parameter ensemble, which is then evaluated with a diverse set of global and spatiotemporally resolved observational constraints. We discuss the performance of the constrained ensemble and use it to formulate a new best-guess version of the model (LPX-Bern v1.4). The observationally constrained ensemble is used to investigate historical emissions due to LULCC (ELUC) and their sensitivity to model parametrization. We find a global ELUC estimate of 158 (108, 211) PgC (median and 90 % confidence interval) between 1800 and 2016. We compare ELUC to other estimates both globally and regionally. Spatial patterns are investigated and estimates of ELUC of the 10 countries with the largest contribution to the flux over the historical period are reported. We consider model versions with and without additional land-use processes (shifting cultivation and wood harvest) and find that the difference in global ELUC is on the same order of magnitude as parameter-induced uncertainty and in some cases could potentially even be offset with appropriate parameter choice.


2020 ◽  
Author(s):  
Yuan Yuan ◽  
Lei Lin

Satellite image time series (SITS) classification is a major research topic in remote sensing and is relevant for a wide range of applications. Deep learning approaches have been commonly employed for SITS classification and have provided state-of-the-art performance. However, deep learning methods suffer from overfitting when labeled data is scarce. To address this problem, we propose a novel self-supervised pre-training scheme to initialize a Transformer-based network by utilizing large-scale unlabeled data. In detail, the model is asked to predict randomly contaminated observations given an entire time series of a pixel. The main idea of our proposal is to leverage the inherent temporal structure of satellite time series to learn general-purpose spectral-temporal representations related to land cover semantics. Once pre-training is completed, the pre-trained network can be further adapted to various SITS classification tasks by fine-tuning all the model parameters on small-scale task-related labeled data. In this way, the general knowledge and representations about SITS can be transferred to a label-scarce task, thereby improving the generalization performance of the model as well as reducing the risk of overfitting. Comprehensive experiments have been carried out on three benchmark datasets over large study areas. Experimental results demonstrate the effectiveness of the proposed method, leading to a classification accuracy increment up to 1.91% to 6.69%. <div><b>This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may no longer be accessible.</b></div>


2020 ◽  
Vol 34 (05) ◽  
pp. 8058-8065
Author(s):  
Katharina Kann ◽  
Samuel R. Bowman ◽  
Kyunghyun Cho

We propose to cast the task of morphological inflection—mapping a lemma to an indicated inflected form—for resource-poor languages as a meta-learning problem. Treating each language as a separate task, we use data from high-resource source languages to learn a set of model parameters that can serve as a strong initialization point for fine-tuning on a resource-poor target language. Experiments with two model architectures on 29 target languages from 3 families show that our suggested approach outperforms all baselines. In particular, it obtains a 31.7% higher absolute accuracy than a previously proposed cross-lingual transfer model and outperforms the previous state of the art by 1.7% absolute accuracy on average over languages.


2021 ◽  
Author(s):  
Ryusei Ishii ◽  
Patrice Carbonneau ◽  
Hitoshi Miyamoto

&lt;p&gt;Archival imagery dating back to the mid-twentieth century holds information that pre-dates urban expansion and the worst impacts of climate change.&amp;#160; In this research, we examine deep learning colorisation methods applied to historical aerial images in Japan.&amp;#160; Specifically, we attempt to colorize monochrome images of river basins by applying the method of Neural Style Transfer (NST).&amp;#160;&amp;#160;&amp;#160; First, we created RGB orthomosaics (1m) for reaches of 3 Japanese rivers, the Kurobe, Ishikari, and Kinu rivers.&amp;#160; From the orthomosaics, we extract 60 thousand image tiles of `100 x100` pixels in order to train the CNN used in NST.&amp;#160; The Image tiles were classified into 6 classes: urban, river, forest, tree, grass, and paddy field.&amp;#160; Second, we use the VGG16 model pre-trained on ImageNet data in a transfer learning approach where we freeze a variable number of layers.&amp;#160; We fine-tuned the training epochs, learning rate, and frozen layers in VGG16 in order to derive the optimal CNN used in NST.&amp;#160; The fine tuning resulted in the F-measure accuracy of 0.961, 0.947, and 0.917 for the freeze layer in 7,11,15, respectively.&amp;#160; Third, we colorize monochrome aerial images by the NST with the retrained model weights.&amp;#160; Here used RGB images for 7 Japanese rivers and the corresponding grayscale versions to evaluate the present NST colorization performance.&amp;#160; The RMSE between the RGB and resultant colorized images showed the best performance with the model parameters of lower content layer (6), shallower freeze layer (7), and larger style/content weighting ratio (1.0 x10&amp;#8309;).&amp;#160; The NST hyperparameter analysis indicated that the colorized images became rougher when the content layer selected deeper in the VGG model.&amp;#160; This is because the deeper the layer, the more features were extracted from the original image.&amp;#160; It was also confirmed that the Kurobe and Ishikari rivers indicated higher accuracy in colorisation.&amp;#160; It might come from the fact that the training dataset of the fine tuning was extracted from these river images.&amp;#160; Finally, we colorized historical monochrome images of Kurobe river with the best NST parameters, resulting in quality high enough compared with the RGB images.&amp;#160; The result indicated that the fine tuning of the NST model could achieve high performance to proceed further land cover classification in future research work.&lt;/p&gt;


2020 ◽  
Vol 34 (05) ◽  
pp. 8815-8821 ◽  
Author(s):  
Sheng Shen ◽  
Zhen Dong ◽  
Jiayu Ye ◽  
Linjian Ma ◽  
Zhewei Yao ◽  
...  

Transformer based architectures have become de-facto models used for a range of Natural Language Processing tasks. In particular, the BERT based models achieved significant accuracy gain for GLUE tasks, CoNLL-03 and SQuAD. However, BERT based models have a prohibitive memory footprint and latency. As a result, deploying BERT based models in resource constrained environments has become a challenging task. In this work, we perform an extensive analysis of fine-tuned BERT models using second order Hessian information, and we use our results to propose a novel method for quantizing BERT models to ultra low precision. In particular, we propose a new group-wise quantization scheme, and we use Hessian-based mix-precision method to compress the model further. We extensively test our proposed method on BERT downstream tasks of SST-2, MNLI, CoNLL-03, and SQuAD. We can achieve comparable performance to baseline with at most 2.3% performance degradation, even with ultra-low precision quantization down to 2 bits, corresponding up to 13× compression of the model parameters, and up to 4× compression of the embedding table as well as activations. Among all tasks, we observed the highest performance loss for BERT fine-tuned on SQuAD. By probing into the Hessian based analysis as well as visualization, we show that this is related to the fact that current training/fine-tuning strategy of BERT does not converge for SQuAD.


1998 ◽  
Vol 84 (6) ◽  
pp. 2070-2088 ◽  
Author(s):  
Thien D. Bui ◽  
Donald Dabdub ◽  
Steven C. George

The steady-state exchange of inert gases across an in situ canine trachea has recently been shown to be limited equally by diffusion and perfusion over a wide range (0.01–350) of blood solubilities (βblood; ml ⋅ ml−1 ⋅ atm−1). Hence, we hypothesize that the exchange of ethanol (βblood = 1,756 at 37°C) in the airways depends on the blood flow rate from the bronchial circulation. To test this hypothesis, the dynamics of the bronchial circulation were incorporated into an existing model that describes the simultaneous exchange of heat, water, and a soluble gas in the airways. A detailed sensitivity analysis of key model parameters was performed by using the method of Latin hypercube sampling. The model accurately predicted a previously reported experimental exhalation profile of ethanol ( R 2= 0.991) as well as the end-exhalation airstream temperature (34.6°C). The model predicts that 27, 29, and 44% of exhaled ethanol in a single exhalation are derived from the tissues of the mucosa and submucosa, the bronchial circulation, and the tissue exterior to the submucosa (which would include the pulmonary circulation), respectively. Although the concentration of ethanol in the bronchial capillary decreased during inspiration, the three key model outputs (end-exhaled ethanol concentration, the slope of phase III, and end-exhaled temperature) were all statistically insensitive ( P > 0.05) to the parameters describing the bronchial circulation. In contrast, the model outputs were all sensitive ( P < 0.05) to the thickness of tissue separating the core body conditions from the bronchial smooth muscle. We conclude that both the bronchial circulation and the pulmonary circulation impact soluble gas exchange when the entire conducting airway tree is considered.


Sign in / Sign up

Export Citation Format

Share Document