scholarly journals Human Skin-Like Composite Materials for Blast Induced Injury Mitigation

2018 ◽  
Vol 2 (3) ◽  
pp. 44 ◽  
Author(s):  
Arnab Chanda ◽  
Rebecca Graeter
Keyword(s):  
Human Skin ◽  
Stress Reduction ◽  
Volume Fraction ◽  
Experimental Testing ◽  
Short Fiber ◽  
Fe Model ◽  
Fiber Types ◽  
Fiber Volume ◽  
Personal Protection Equipment ◽  
The Matrix

Armors and military grade personal protection equipment (PPE) materials to date are bulky and are not designed to effectively mitigate blast impacts. In the current work, a human skin-like castable simulant material was developed and its blast mitigation characteristics (in terms of induced stress reduction at the bone and muscles) were characterized in the presence of composite reinforcements. The reinforcement employed was Kevlar 129 (commonly used in advanced combat helmets), which was embedded within the novel skin simulant material as the matrix and used to cover a representative extremity based human skin, muscle and bone section finite element (FE) model. The composite variations tested were continuous and short-fiber types, lay-ups (0/0, 90/0, and 45/45 orientations) and different fiber volume fractions. From the analyses, the 0/0 continuous fiber lay-up with a fiber volume fraction close to 0.1 (or 10%) was found to reduce the blast-induced dynamic stresses at the bone and muscle sections by 78% and 70% respectively. These findings indicate that this novel skin simulant material with Kevlar 129 reinforcement, with further experimental testing, may present future opportunities in blast resistant armor padding designing.

Effect of Fiber Volume Fraction on High Temperature Creep of Al2O3-SiO2(sf)/AZ91D Composite

2011 ◽  
Vol 474-476 ◽  
pp. 548-552
Author(s):  
Jun Tian
Keyword(s):  
Creep Resistance ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Matrix Alloy ◽  
Short Fiber ◽  
Tensile Creep ◽  
Short Fibers ◽  
Creep Tests ◽  
Fiber Volume ◽  
The Matrix

Constant stress tensile creep tests were conducted on AZ91D–20 vol.%, 25 vol.%, and 30 vol.% Al2O3-SiO2short fiber composites and on an unreinforced AZ91D matrix alloy. The creep resistance of the reinforced materials is shown to be considerably improved compared with the matrix alloy. With the increasing volume fraction of short fibers, the creep resistance of AZ91D composites is improved, and their creep threshold stresses are also increased accordingly. Because of the increasing volume fraction of short fibers, loads of bearing and transmission of short fibers will increase, and thus the creep resistance of AZ91D composites further improves, but the precipitation of β-Mg17Al12precipitate increases in the number, it is easy to soften coarse, so that threshold stress of AZ91D composite does not increase greatly.

Determination of fiber volume fraction in a cured laminate

2021 ◽  
pp. 002199832110112
Author(s):  
Qing Yang Steve Wu ◽  
Nan Zhang ◽  
Weng Heng Liew ◽  
Vincent Lim ◽  
Xiping Ni ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Volume Fraction ◽  
Evaluation Method ◽  
Volume Fraction ◽  
Matrix Material ◽  
Volume Ratio ◽  
Gravimetric Analysis ◽  
Fiber Volume ◽  
Laser Ultrasonic ◽  
The Matrix

Propagation of ultrasonic wave in Carbon Fiber Reinforced Polymer (CFRP) is greatly influenced by the material’s matrix, resins and fiber volume ratio. Laser ultrasonic broadband spectral technique has been demonstrated for porosity and fiber volume ratio extraction on unidirection aligned CFRP laminates. Porosity in the matrix materials can be calculated by longitudinal wave attenuation and accurate fiber volume ratio can be derived by combined velocity through the high strength carbon fiber and the matrix material with further consideration of porosity effects. The results have been benchmarked by pulse-echo ultrasonic tests, gas pycnometer and thermal gravimetric analysis (TGA). The potentials and advantages of the laser ultrasonic technique as a non-destructive evaluation method for CFRP carbon fiber volume fraction evaluation were demonstrated.

Effect of surface density and fiber length on the porosity and permeability of nonwoven flax reinforcement

2017 ◽  
Vol 88 (15) ◽  
pp. 1776-1787 ◽  
Author(s):  
Mohamed Habibi ◽  
Édu Ruiz ◽  
Gilbert Lebrun ◽  
Luc Laperrière
Keyword(s):  
Pore Size ◽  
Surface Density ◽  
Fiber Length ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Short Fiber ◽  
Fiber Volume ◽  
Fibrous Network ◽  
Porosity And Permeability ◽  
The Impact

This paper presents an experimental study and modeling of the influence of surface density and fiber length on the permeability of novel nonwoven flax fiber manufactured by the paper making process. Firstly, the relation between surface density, fiber lengths and pore size distribution measured with a porometer capillary instrument is reported in this study. The results show that higher surface density gives a denser fibrous network with a low porosity rate and longer fiber decreases the total number of fibers and increases the pore size for a given surface density. A liquid permeability study was then carried out to identify the impact of surface density, short fiber length and fiber volume fraction on in-plane impregnation of the reinforcement. Permeability was found to be inversely proportional to the reinforcement of surface density. In contrast, an increase of the fiber length increases the in-plane permeability of the reinforcement. Finally, a mathematical modeling is proposed to predict the permeability behavior of these innovative natural fiber webs.

Development of Generalized Plane-Strain Tensors for the Concentric Cylinder

1995 ◽  
Vol 62 (3) ◽  
pp. 590-594
Author(s):  
N. Chandra ◽  
Zhiyum Xie
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Transformation Strain ◽  
Inclusion Problem ◽  
Infinite Domain ◽  
Concentric Cylinder ◽  
Finite Radius ◽  
Fiber Volume ◽  
Thermal Residual Stresses ◽  
The Matrix

A pair of two new tensors called GPS tensors S and D is proposed for the concentric cylindrical inclusion problem. GPS tensor S relates the strain in the inclusion constrained by the matrix of finite radius to the uniform transformation strain (eigenstrain), whereas tensor D relates the strain in the matrix to the same eigenstrain. When the cylindrical matrix is of infinite radius, tensor S reduces to the appropriate Eshelby’s tensor. Explicit expressions to evaluate thermal residual stresses σr, σθ and σz in the matrix and the fiber using tensor D and tensor S, respectively, are developed. Since the geometry of the present problem is of finite radius, the effect of fiber volume fraction on the stress distribution can be easily studied. Results for the thermal residual stress distributions are compared with Eshelby’s infinite domain solution and finite element results for a specified fiber volume fraction.

Fracture behavior of short-fiber reinforced materials

1992 ◽  
Vol 7 (11) ◽  
pp. 3120-3131 ◽  
Author(s):  
Michael Murat ◽  
Micha Anholt ◽  
H. Daniel Wagner
Keyword(s):  
Fracture Process ◽  
Fracture Behavior ◽  
Volume Fraction ◽  
Fiber Composite ◽  
Finite Size ◽  
Critical Length ◽  
Short Fiber ◽  
Fiber Volume ◽  
Linear Elastic ◽  
Fiber Reinforced Materials

A discrete model of springs with bond-bending forces is proposed to simulate the fracture process in a composite of short stiff fibers in a softer matrix. Both components are assumed to be linear elastic up to failure. We find that the critical fiber length of a single fiber composite increases roughly linearly with the ratio of the fiber elastic modulus to matrix modulus. The finite size of the lattice in the direction perpendicular to the fiber orientation considerably alters the behavior of the critical length for large values of the modulus ratio. The simulations of the fracture process reveal different fracture behavior as a function of the fiber content and length. We calculate the Young's modulus, fracture stress, and the strain at maximum stress as a function of the fiber volume fraction and aspect ratio. The results are compared with the predictions of other theoretical studies and experiments.

A Study on the Thermoelastic Analysis in Shear Deformable Discontinuous Composites

2004 ◽  
Vol 261-263 ◽  
pp. 645-650
Author(s):  
Hong Gun Kim
Keyword(s):  
Thermal Stresses ◽  
Volume Fraction ◽  
Coefficient Of Thermal Expansion ◽  
Fiber Composite ◽  
Element Model ◽  
Short Fiber ◽  
Elastic Stresses ◽  
Fiber Aspect Ratio ◽  
The Matrix ◽  
Lag Model

A stress analysis has been performed to evaluate the thermally induced elastic stresses which can develop in a short fiber composite due to coefficient of thermal expansion (CTE) mismatch. An axisymmetric finite element model with the constraint between cells has implemented to find the magnitude of thermoelastic stresses in the fiber and the matrix as a function of volume fraction, CTE ratio, modulus ratio, and fiber aspect ratio. It was found that the matrix end regions fall under significant thermal stresses that have the same sign as that of the fibers themselves. Furthermore, it was found that the stresses vary along the fiber and fiber end gap in the same manner as that obtained in a shear-lag model during non-thermal mechanical loading.

A Methodology for Synthesizing High-Performance Robots Fabricated With Optimally Tailored Composite Laminates

1987 ◽  
Vol 109 (1) ◽  
pp. 74-86 ◽  
Author(s):  
C. K. Sung ◽  
B. S. Thompson
Keyword(s):  
Composite Laminates ◽  
High Performance ◽  
Volume Fraction ◽  
Three Dimensional ◽  
High Strength ◽  
Fiber Volume ◽  
Cross Sectional ◽  
Fiber Properties ◽  
Robot Arms ◽  
The Matrix

An essential ingredient of the next generation of robotic manipulators will be high-strength lightweight arms which promise high-performance characteristics. Currently, a design methodology for optimally synthesizing these essential robotic components does not exist. Herein, an approach is developed for addressing this void in the technology-base by integrating state-of-the-art techniques in both the science of composite materials and also the science of flexible robotic systems. This approach is based on the proposition that optimal performance can be achieved by fabricating robot arms with optimal cross-sectional geometries fabricated with optimally tailored composite laminates. A methodology is developed herein which synthesizes the manufacturing specification for laminates which are specifically tailored for robotic applications in which both high-strength, high-stiffness robot arms are required which also possess high material damping. The parameters in the manufacturing specification include the fiber-volume fraction, the matrix properties, the fiber properties, the ply layups, the stacking sequence and the ply thicknesses. This capability is then integrated within a finite-element methodology for analyzing the dynamic response of flexible robots. An illustrative example demonstrates the approach by simulating the three-dimensional elastodynamic response of a robot subjected to a prescribed spatial maneuver.

Fiber-Matrix Interfacial Area Reduction in Fiber Reinforced Cements and Concretes at Moderate to High Fiber Volume Fractions

1994 ◽  
Vol 370 ◽  
Author(s):  
Gebran N. Karam
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Interfacial Area ◽  
Composite Fiber ◽  
Short Fiber ◽  
Published Data ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
High Fiber ◽  
Fiber Matrix

AbstractThe area and properties of the fiber-matrix interface in fiber reinforced cements and concretes determines the amount of stress transferred forth and back between the cement paste and the reinforcement and hence controls the mechanical properties of the composite. Fiber-fiber interaction and overlap of fibers with fibers, voids and aggregates can dramatically decrease the efficiency of the reinforcement by reducing this interfacial area. A simple model to account for this reduction is proposed and ways to integrate it in the models describing the mechanical properties of short fiber reinforced concretes are presented. The parameters of the model are evaluated from previously published data sets and its predictions are found to compare well with experimental observations; for example, it is able to predict the non-linear variation of bending and tensile strength with increasing fiber volume fraction as well as the existence of an optimal fiber content.

Sign in / Sign up

Export Citation Format

Share Document