scholarly journals Carbon Fiber Reinforced PEEK Composites Based on 3D-Printing Technology for Orthopedic and Dental Applications

2019 ◽  
Vol 8 (2) ◽  
pp. 240 ◽  
Author(s):  
Xingting Han ◽  
Dong Yang ◽  
Chuncheng Yang ◽  
Sebastian Spintzyk ◽  
Lutz Scheideler ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Fiber Reinforced ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Peek Composite ◽  
Carbon Fiber Reinforced ◽  
Mechanical Strengths

Fused deposition modeling (FDM) is a rapidly growing three-dimensional (3D) printing technology and has great potential in medicine. Polyether-ether-ketone (PEEK) is a biocompatible high-performance polymer, which is suitable to be used as an orthopedic/dental implant material. However, the mechanical properties and biocompatibility of FDM-printed PEEK and its composites are still not clear. In this study, FDM-printed pure PEEK and carbon fiber reinforced PEEK (CFR-PEEK) composite were successfully fabricated by FDM and characterized by mechanical tests. Moreover, the sample surfaces were modified with polishing and sandblasting methods to analyze the influence of surface roughness and topography on general biocompatibility (cytotoxicity) and cell adhesion. The results indicated that the printed CFR-PEEK samples had significantly higher general mechanical strengths than the printed pure PEEK (even though there was no statistical difference in compressive strength). Both PEEK and CFR-PEEK materials showed good biocompatibility with and without surface modification. Cell densities on the “as-printed” PEEK and the CFR-PEEK sample surfaces were significantly higher than on the corresponding polished and sandblasted samples. Therefore, the FDM-printed CFR-PEEK composite with proper mechanical strengths has potential as a biomaterial for bone grafting and tissue engineering applications.

scholarly journals The Micro–Macro Interlaminar Properties of Continuous Carbon Fiber-Reinforced Polyphenylene Sulfide Laminates Made by Thermocompression to Simulate the Consolidation Process in FDM

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 301
Author(s):  
Jiale Hu ◽  
Suhail Mubarak ◽  
Kunrong Li ◽  
Xu Huang ◽  
Weidong Huang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
3D Printing ◽  
Manufacturing Industry ◽  
Fused Deposition Modeling ◽  
Polyphenylene Sulfide ◽  
Fiber Reinforced ◽  
Continuous Fiber ◽  
Fused Deposition ◽  
Continuous Carbon Fiber ◽  
Carbon Fiber Reinforced

Three-dimensional (3D) printing of continuous fiber-reinforced composites has been developed in recent decades as an alternative means to handle complex structures with excellent design flexibility and without mold forming. Although 3D printing has been increasingly used in the manufacturing industry, there is still room for the development of theories about how the process parameters affect microstructural properties to meet the mechanical requirements of the printed parts. In this paper, we investigated continuous carbon fiber-reinforced polyphenylene sulfide (CCF/PPS) as feedstock for fused deposition modeling (FDM) simulated by thermocompression. This study revealed that the samples manufactured using a layer-by-layer process have a high tensile strength up to 2041.29 MPa, which is improved by 68.8% compared with those prepared by the once-stacked method. Moreover, the mechanical–microstructure characterization relationships indicated that the compactness of the laminates is higher when the stacked CCF/PPS are separated, which can be explained based on both the void formation and the nanoindentation results. These reinforcements confirm the potential of remodeling the layer-up methods for the development of high-performance carbon fiber-reinforced thermoplastics. This study is of great significance to the improvement of the FDM process and opens broad prospects for the aerospace industry and continuous fiber-reinforced polymer matrix materials.

scholarly journals Desain dan Pembuatan Prototype Piston Honda MEGAPRO FI Menggunakan 3D Printing

2020 ◽  
Vol 1 (2) ◽  
pp. 81-91
Author(s):  
Frince Marbun ◽  
Richard A.M. Napitupulu
Keyword(s):  
3D Printing ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Manufacturing Technologies ◽  
Aided Design

3D printing technology has great potential in today's manufacturing world, one of its uses is in making miniatures or prototypes of a product such as a piston. One of the most famous and inexpensive 3D printing (additive manufacturing) technologies is Fused Deposition Modeling (FDM), the principle FDM works by thermoplastic extrusion through a hot nozzle at melting temperature then the product is made layer by layer. The two most commonly used materials are ABS and PLA so it is very important to know the accuracy of product dimensions. FDM 3D Printing Technology is able to make duplicate products accurately using PLA material. FDM machines work by printing parts that have been designed by computer-aided design (CAD) and then exported in the form of STL or .stl files and uploaded to the slicer program to govern the printing press according to the design. Using Anet A8 brand 3D printing tools that are available to the public, Slicing of general CAD geometry files such as autocad and solidwork is the basis for making this object. This software is very important to facilitate the design process to be printed. Some examples of software that can be downloaded and used free of charge such as Repetier-Host and Cura. by changing the parameters in the slicer software is very influential in the 3D printing manufacturing process.

Design and Verification of a Metal 3D Printing Device Based on Contact Resistance Heating

2019 ◽  
Vol 298 ◽  
pp. 64-68
Author(s):  
Yu Hua Dai ◽  
Xi Wang
Keyword(s):  
3D Printing ◽  
Contact Resistance ◽  
Fused Deposition Modeling ◽  
Numerical Control ◽  
Control Technique ◽  
Resistance Heating ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Metal 3D Printing

As a branch of 3D printing technology, metal 3D printing is an important advanced manufacturing processing method. Metal 3D printing technology has been widely applied in a variety of areas, including the aerospace field, biomedical research and mold manufacturing. This paper proposed a new method for melting metal wires via contact resistance heating. Through the combination of a numerical control technique, a mechanical structure and computer software, a metal 3D printing device was designed based on the principle of fused deposition modeling. The printing nozzle of the device can be heated to over 1400°C in a few minutes. Additionally, we performed experiments with aluminum wire to demonstrate the feasibility of the printing method. The designed consumer-level desktop metal 3D printer cost less than 1500 dollars to fabricate.

Tensile Strength and Flexural Strength Testing of Acrylonitrile Butadiene Styrene (ABS) Materials for Biomimetic Robotic Applications

2014 ◽  
Vol 20 ◽  
pp. 11-21 ◽  
Author(s):  
Tran Linh Khuong ◽  
Zhao Gang ◽  
Muhammad Farid ◽  
Rao Yu ◽  
Zhuang Zhi Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Butadiene Styrene

Biomimetic robots borrow their structure, senses and behavior from animals, such as humans or insects, and plants. Biomimetic design is design ofa machine, a robot or a system in engineeringdomain thatmimics operational and/orbehavioral model of a biological system in nature. 3D printing technology has another name as rapid prototyping technology. Currently it is being developed fastly and widely and is applied in many fields like the jewelry, footwear, industrial design, architecture, engineering and construction, automotive, aerospace, dental and medical industry, education, geographic information system, civil engineering, guns. 3D printing technology is able to manufacture complicated, sophisticated details that the traditional processing method cannot manufacture. Therefore, 3D printing technology can be seen as an effective tool in biomimetic, which can accurately simulate most of the biological structure. Fused Deposition Modeling (FDM) is a technology of the typical rapid prototyping. The main content of the article is the focusing on tensile strength test of the ABS-Acrylonitrile Butadiene Styrene material after using Fused Deposition Modeling (FDM) technology, concretization after it’s printed by UP2! 3D printer. The article focuses on two basic features which are Tensile Strength and Determination of flexural properties.

3D Printing of Carbon Fiber Reinforced Plastics and their Applications

2018 ◽  
Vol 913 ◽  
pp. 558-563 ◽  
Author(s):  
Wei Dong Zhou ◽  
Jian Sheng Chen
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
3D Printing ◽  
Complex Structure ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fused Deposition ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

3D printing of carbon fiber reinforced plastics can produce lightweight components with higher efficiency and more complex structure. For the short carbon fiber reinforced plastics, the composites are firstly made by compounding, then they are processed to filaments, powders or other needed forms, finally the components are printed by Fused Deposition Modeling (FDM), Selected Laser Sintering (SLS) or other methods. The tensile strength of the nylon-based component is more than 70 MPa. Companies such as EOS, Stratasys and Farsoon can provide the materials and equipments. For the continuous carbon fiber reinforced plastics, the divided carbon fibers and plastic filaments or impregnated carbon fiber filaments are firstly prepared, then the components are printed by FDM or other methods. The average tensile strength of the nylon-based component is more than 200 MPa. Companies such as Markforged and Arevo Labs have commercialized the 3D printing equipment/platform for the continuous fiber reinforced plastics.

Realization of Modified Elliptical Shaped Dielectric Lens Antenna for X Band Applications with 3D Printing Technology

2020 ◽  
Vol 35 (8) ◽  
pp. 916-921
Author(s):  
Aysu Belen ◽  
Evrim Tetik
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
High Gain ◽  
Printing Technology ◽  
Lens Antenna ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Dielectric Lens ◽  
3D Em

Placing dielectric lens structures into an antenna's aperture has proven to be one of the most reliable methods of enhancing its gain. However, the selected material and the prototyping method usually limit their fabrication process. With the advances in 3D printing technology and their applications, the microwave designs that were either impractical or impossible in the past to manufacture using traditional methods, are now feasible. Herein, a novel prototyping method by using 3D-printer technology for low-cost, broadband, and high gain dielectric lens designs has been presented. Firstly, the elliptical lens design has been modeled in the 3D EM simulation environment. Then fused deposition modeling based 3D-printing method has been used for the fabrication of the dielectric lens. The measured results of the 3D printed antenna show that the lens antenna has a realized gain of 17 to 20.5 dBi over 8-12 GHz. Moreover, the comparison of the prototyped antenna with its counterpart dielectric lens antenna in the literature has indicated that the proposed method is more efficient, more beneficial, and has a lower cost.

Sign in / Sign up

Export Citation Format

Share Document