scholarly journals Electrophoretic Deposition of Copper(II)–Chitosan Complexes for Antibacterial Coatings

2020 ◽  
Vol 21 (7) ◽  
pp. 2637 ◽  
Author(s):  
Muhammad Asim Akhtar ◽  
Kanwal Ilyas ◽  
Ivo Dlouhý ◽  
Filip Siska ◽  
Aldo R. Boccaccini
Keyword(s):  
Electrophoretic Deposition ◽  
Mechanical Stability ◽  
Metallic Copper ◽  
Antibacterial Properties ◽  
Threshold Concentration ◽  
X Ray Diffraction ◽  
X Ray ◽  
Antibacterial Coatings ◽  
Elemental Analyses ◽  
The Stability

Bacterial infection associated with medical implants is a major threat to healthcare. This work reports the fabrication of Copper(II)–Chitosan (Cu(II)–CS) complex coatings deposited by electrophoretic deposition (EPD) as potential antibacterial candidate to combat microorganisms to reduce implant related infections. The successful deposition of Cu(II)–CS complex coatings on stainless steel was confirmed by physicochemical characterizations. Morphological and elemental analyses by scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) spectroscopy verified the uniform distribution of copper in the Chitosan (CS) matrix. Moreover, homogeneous coatings without precipitation of metallic copper were confirmed by X-ray diffraction (XRD) spectroscopy and SEM micrographs. Controlled swelling behavior depicted the chelation of copper with polysaccharide chains that is key to the stability of Cu(II)–CS coatings. All investigated systems exhibited stable degradation rate in phosphate buffered saline (PBS)–lysozyme solution within seven days of incubation. The coatings presented higher mechanical properties with the increase in Cu(II) concentration. The crack-free coatings showed mildly hydrophobic behavior. Antibacterial assays were performed using both Gram-positive and Gram-negative bacteria. Outstanding antibacterial properties of the coatings were confirmed. After 24 h of incubation, cell studies of coatings confirms that up to a certain threshold concentration of Cu(II) were not cytotoxic to human osteoblast-like cells. Overall, our results show that uniform and homogeneous Cu(II)–CS coatings with good antibacterial and enhanced mechanical stability could be successfully deposited by EPD. Such antibiotic-free antibacterial coatings are potential candidates for biomedical implants.

scholarly journals A Superhydrophobic, Antibacterial, and Durable Surface of Poplar Wood

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1885
Author(s):  
Xinyu Wu ◽  
Feng Yang ◽  
Jian Gan ◽  
Zhangqian Kong ◽  
Yan Wu
Keyword(s):  
Stearic Acid ◽  
Antibacterial Properties ◽  
Alkali Resistance ◽  
Poplar Wood ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Acid And Alkali Resistance ◽  
The Stability

The silver particles were grown in situ on the surface of wood by the silver mirror method and modified with stearic acid to acquire a surface with superhydrophobic and antibacterial properties. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray energy spectroscopy (XPS) were used to analyze the reaction mechanism of the modification process. Scanning electron microscopy (SEM) and contact angle tests were used to characterize the wettability and surface morphology. A coating with a micro rough structure was successfully constructed by the modification of stearic acid, which imparted superhydrophobicity and antibacterial activity to poplar wood. The stability tests were performed to discuss the stability of its hydrophobic performance. The results showed that it has good mechanical properties, acid and alkali resistance, and UV stability. The durability tests demonstrated that the coating has the function of water resistance and fouling resistance and can maintain the stability of its hydrophobic properties under different temperatures of heat treatment.

Fractionation of polymethylene chains: An electron crystallographic investigation

1986 ◽  
Vol 44 ◽  
pp. 794-795
Author(s):  
Douglas L. Dorset
Keyword(s):  
Cross Section ◽  
Binary Systems ◽  
Linear Chain ◽  
Pure Component ◽  
Organic Substrates ◽  
Crystallographic Investigation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molecular Sizes ◽  
The Stability

A variety of linear chain materials exist as polydisperse systems which are difficultly purified. The stability of continuous binary solid solutions assume that the Gibbs free energy of the solution is lower than that of either crystal component, a condition which includes such factors as relative molecular sizes and shapes and perhaps the symmetry of the pure component crystal structures.Although extensive studies of n-alkane miscibility have been carried out via powder X-ray diffraction of bulk samples we have begun to examine binary systems as single crystals, taking advantage of the well-known enhanced scattering cross section of matter for electrons and also the favorable projection of a paraffin crystal structure posited by epitaxial crystallization of such samples on organic substrates such as benzoic acid.

scholarly journals Synthesis of Bis(Carboranyl)amides 1,1′-μ-(CH2NH(O)C(CH2)n-1,2-C2B10H11)2 (n = 0, 1) and Attempt of Synthesis of Gadolinium Bis(Dicarbollide)

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1321
Author(s):  
Yasunobu Asawa ◽  
Aleksandra V. Arsent’eva ◽  
Sergey A. Anufriev ◽  
Alexei A. Anisimov ◽  
Kyrill Yu. Suponitsky ◽  
...  
Keyword(s):  
Molecular Structure ◽  
Single Crystal ◽  
Quantum Chemical Calculations ◽  
Quantum Chemical ◽  
X Ray Diffraction ◽  
Stable Conformation ◽  
Acyl Chlorides ◽  
X Ray ◽  
Cesium Fluoride ◽  
The Stability

Bis(carboranyl)amides 1,1′-μ-(CH2NH(O)C(CH2)n-1,2-C2B10H11)2 (n = 0, 1) were prepared by the reactions of the corresponding carboranyl acyl chlorides with ethylenediamine. Crystal molecular structure of 1,1′-μ-(CH2NH(O)C-1,2-C2B10H11)2 was determined by single crystal X-ray diffraction. Treatment of bis(carboranyl)amides 1,1′-μ-(CH2NH(O)C(CH2)n-1,2-C2B10H11)2 with ammonium or cesium fluoride results in partial deboronation of the ortho-carborane cages to the nido-carborane ones with formation of [7,7′(8′)-μ-(CH2NH(O)C(CH2)n-7,8-C2B9H11)2]2−. The attempted reaction of [7,7′(8′)-μ-(CH2NH(O)CCH2-7,8-C2B9H11)2]2− with GdCl3 in 1,2-dimethoxy- ethane did not give the expected metallacarborane. The stability of different conformations of Gd-containing metallacarboranes has been estimated by quantum-chemical calculations using [3,3-μ-DME-3,3′-Gd(1,2-C2B9H11)2]− as a model. It was found that in the most stable conformation the CH groups of the dicarbollide ligands are in anti,anti-orientation with respect to the DME ligand, while any rotation of the dicarbollide ligand reduces the stability of the system. This makes it possible to rationalize the design of carborane ligands for the synthesis of gadolinium metallacarboranes on their base.

scholarly journals Facile Organometallic Synthesis of Fe-Based Nanomaterials by Hot Injection Reaction

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1141
Author(s):  
Georgia Basina ◽  
Hafsa Khurshid ◽  
Nikolaos Tzitzios ◽  
George Hadjipanayis ◽  
Vasileios Tzitzios
Keyword(s):  
Room Temperature ◽  
Colloidal Particles ◽  
Iron Pentacarbonyl ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
Organometallic Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Hot Injection ◽  
The Stability

Fe-based colloids with a core/shell structure consisting of metallic iron and iron oxide were synthesized by a facile hot injection reaction of iron pentacarbonyl in a multi-surfactant mixture. The size of the colloidal particles was affected by the reaction temperature and the results demonstrated that their stability against complete oxidation related to their size. The crystal structure and the morphology were identified by powder X-ray diffraction and transmission electron microscopy, while the magnetic properties were studied at room temperature with a vibrating sample magnetometer. The injection temperature plays a very crucial role and higher temperatures enhance the stability and the resistance against oxidation. For the case of injection at 315 °C, the nanoparticles had around a 10 nm mean diameter and revealed 132 emu/g. Remarkably, a stable dispersion was created due to the colloids’ surface functionalization in a nonpolar solvent.

scholarly journals Study of Corrosion Resistance and Degradation Mechanisms in LiTiO2-Li2TiO3 Ceramic

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 753
Author(s):  
Dmitriy Shlimas ◽  
Artem L. Kozlovskiy ◽  
Maxim Zdorovets
Keyword(s):  
Degradation Mechanism ◽  
Diffraction Method ◽  
Large Mass ◽  
Time Frame ◽  
X Ray Diffraction ◽  
Acidic Media ◽  
X Ray ◽  
Mass Losses ◽  
The Stability ◽  
Thermal Sintering

The interest in lithium-containing ceramics is due to their huge potential as blanket materials for thermonuclear reactors for the accumulation of tritium. However, an important factor in their use is the preservation of the stability of their strength and structural properties when under the influence of external factors that determine the time frame of their operation. This paper presents the results of a study that investigated the influence of the LiTiO2 phase on the increasing resistance to degradation and corrosion of Li2TiO3 ceramic when exposed to aggressive acidic media. Using the X-ray diffraction method, it was found that an increase in the concentration of LiClO4·3H2O during synthesis leads to the formation of a cubic LiTiO2 phase in the structure as a result of thermal sintering of the samples. During corrosion tests, it was found that the presence of the LiTiO2 phase leads to a decrease in the degradation rate in acidic media by 20–70%, depending on the concentration of the phase. At the same time, and in contrast to the samples of Li2TiO3 ceramics, for which the mechanisms of degradation during a long stay in aggressive media are accompanied by large mass losses, for the samples containing the LiTiO2 phase, the main degradation mechanism is pitting corrosion with the formation of pitting inclusions.

Rapid Thermal Oxidation for Passivation of Porous Silicon

1994 ◽  
Vol 342 ◽  
Author(s):  
I. BÁrsony ◽  
J.G.E. Klappe ◽  
É. Vázsonyi ◽  
T. Lohner ◽  
M. Fried
Keyword(s):  
Porous Silicon ◽  
Mechanical Stability ◽  
Porous Substrate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Si Substrates ◽  
Tetragonal Lattice ◽  
Optical Heating ◽  
Vertical Inhomogeneity ◽  
Highly Porous

ABSTRACTChemical and mechanical stability of porous silicon layers (PSL) is the prerequisite of any active (luminescent) or passive (e.g. porous substrate) integrated applications. In this work X-ray diffraction (XRD) was used to analyze quantitatively the strain distribution obtained in different morphology PSL that were prepared on (100) p and p+Si substrates. Tetragonal lattice constant distortion can be as high as 1.4% in highly porous “as-prepared” samples. Incoherent optical heating RTO is governed by the absorption in the oxidized specimen. PSL show vertical inhomogeneity according to interpretation of spectroscopic ellipsometry (SE) data. Oxygen incorporation during RTO is controlled by specific surface (in p+ proportional, in p inversely proportional with porosity), while the developing compressive stress depends on pore size, and decreases with porosity in both morphologies.

Polydomain Structure of Epitaxial PbTiO3 films on MgO

1997 ◽  
Vol 493 ◽  
Author(s):  
S. P. Alpay ◽  
A. S. Prakash ◽  
S. Aggarwal ◽  
R. Ramesh ◽  
A. L. Roytburd ◽  
...  
Keyword(s):  
Domain Structure ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Theoretical Predictions ◽  
The Stability ◽  
Increasing Temperature ◽  
Stable Domains ◽  
Domain Stability

ABSTRACTA PbTiO3(001) film grown on MgO(001) by pulsed laser deposition is examined as an example to demonstrate the applications of the domain stability map for epitaxial perovskite films which shows regions of stable domains and fractions of domains in a polydomain structure. X-ray diffraction studies indicate that the film has a …c/a/c/a… domain structure in a temperature range of °C to 400°C with the fraction of c-domains decreasing with increasing temperature. These experimental results are in excellent agreement with theoretical predictions based on the stability map.

Synthesis of 4-(3-coumarinyl)-3-benzyl-4-thiazolin-2-one 4-methylbenzylidenehydrazone and determination of the isomeric structure by X-ray analysis

2003 ◽  
Vol 218 (12) ◽  
Author(s):  
Süheyla Özbey ◽  
Nilgün Karalı ◽  
Aysel Gürsoy
Keyword(s):  
Single Crystal ◽  
Diffraction Analysis ◽  
Spectral Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Isomeric Structure ◽  
Elemental Analyses

AbstractIn this study 4-(3-coumarinyl)-3-benzyl-4-thi azolin-2-one 4-methylbenzylidenehydrazone 3 was synthesised. An independent proof of the thiazolylhydrazone structure of 3 was achieved by single crystal X-ray diffraction analysis. Elemental analyses and spectral data (IR,

scholarly journals High temperature structural study of decagonal Al-Cu-Rh quasicrystal.

2014 ◽  
Vol 70 (a1) ◽  
pp. C94-C94
Author(s):  
Pawel Kuczera ◽  
Walter Steurer
Keyword(s):  
Structural Changes ◽  
Configurational Entropy ◽  
Lattice Vibrations ◽  
X Ray Diffraction ◽  
Stabilization Mechanism ◽  
X Ray ◽  
Comparative Structure ◽  
The Stability

The structure of d(ecagonal)-Al-Cu-Rh has been studied as a function of temperature by in-situ single-crystal X-ray diffraction in order to contribute to the discussion on energy or entropy stabilization of quasicrystals (QC) [1]. The experiments were performed at 293 K, 1223 K, 1153 K, 1083 K, and 1013 K. A common subset of 1460 unique reflections was used for the comparative structure refinements at each temperature. The results obtained for the HT structure refinements of d-Al-Cu-Rh QC seem to contradict a pure phasonic-entropy-based stabilization mechanism [2] for this QC. The trends observed for the ln func(I(T1 )/I(T2 )) vs.|k⊥ |^2 plots indicate that the best on-average quasiperiodic order exists between 1083 K and 1153 K, however, what that actually means is unclear. It could indicate towards a small phasonic contribution to entropy, but such contribution is not seen in the structure refinements. A rough estimation of the hypothetic phason instability temperature shows that it would be kinetically inaccessible and thus the phase transition to a 12 Å low T structure (at ~800 K) is most likely not phason-driven. Except for the obvious increase in the amplitude of the thermal motion, no other significant structural changes, in particular no sources of additional phason-related configurational entropy, were found. All structures are refined to very similar R-values, which proves that the quality of the refinement at each temperature is the same. This suggests, that concerning the stability factors, some QCs could be similar to other HT complex intermetallic phases. The experimental results clearly show that at least the ~4 Å structure of d-Al-Cu-Rh is a HT phase therefore entropy plays an important role in its stabilisation mechanism lowering the free energy. However, the main source of this entropy is probably not related to phason flips, but rather to lattice vibrations, occupational disorder unrelated to phason flips like split positions along the periodic axis.

Study on Influence of Silicate Morphology Based on pH Value

2012 ◽  
Vol 454 ◽  
pp. 324-328
Author(s):  
Yan He ◽  
Ya Jing Liu ◽  
Yong Lin Cao ◽  
Li Xia Zhou
Keyword(s):  
Silicic Acid ◽  
Ph Value ◽  
Colorimetric Method ◽  
Absorption Spectrometry ◽  
Degree Of Polymerization ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
The Stability

Infra-red absorption spectrometry, X-ray diffraction observations and characterization tests based on silicon molybdenum colorimetric method were used to investigate the optimal pH value controlling the stability of the silicic acid form. The experiment process was done by using sodium silicate as raw material. The results showed that the solution of silicate influenced the polymerization. The active silicic acid solution with a certain degree of polymerization was obtained by controlling the pH values.

Sign in / Sign up

Export Citation Format

Share Document