scholarly journals Biodegradable and Toughened Composite of Poly(Propylene Carbonate)/Thermoplastic Polyurethane (PPC/TPU): Effect of Hydrogen Bonding

2018 ◽  
Vol 19 (7) ◽  
pp. 2032 ◽  
Author(s):  
Dongmei Han ◽  
Guiji Chen ◽  
Min Xiao ◽  
Shuanjin Wang ◽  
Shou Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Propylene Carbonate ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Thermal Stabilities ◽  
Dynamic Mechanical ◽  
Brittle Ductile Transition ◽  
Poly Propylene

The blends of Poly(propylene carbonate) (PPC) and polyester-based thermoplastic polyurethane (TPU) were melt compounded in an internal mixer. The compatibility, thermal behaviors, mechanical properties and toughening mechanism of the blends were investigated using Fourier transform infrared spectra (FTIR), tensile tests, impact tests, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dynamic mechanical analysis technologies. FTIR and SEM examination reveal strong interfacial adhesion between PPC matrix and suspended TPU particles. Dynamic mechanical analyzer (DMA) characterize the glass transition temperature, secondary motion and low temperature properties. By the incorporation of TPU, the thermal stabilities are greatly enhanced and the mechanical properties are obviously improved for the PPC/TPU blends. Moreover, PPC/TPU blends exhibit a brittle-ductile transition with the addition of 20 wt % TPU. It is considered that the enhanced toughness results in the shear yielding occurred in both PPC matrix and TPU particles of the blends.

scholarly journals Amino-Functionalized Lead Phthalocyanine-Modified Benzoxazine Resin: Curing Kinetics, Thermal, and Mechanical Properties

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1855 ◽  
Author(s):  
Li-wu Zu ◽  
Bao-chang Gao ◽  
Zhong-cheng Pan ◽  
Jun Wang ◽  
Abdul Qadeer Dayo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Kinetic Parameters ◽  
Curing Kinetics ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Curing Temperature ◽  
Scanning Calorimetry ◽  
Thermal Stabilities ◽  
Dynamic Mechanical

Phenol-diaminodiphenylmethane-based benzoxazine (P-ddm)/phthalocyanine copolymer was prepared by using P-ddm resin as matrix and 3,10,17,24-tetra-aminoethoxy lead phthalocyanine (APbPc) as additive. Fourier-transform infrared (FTIR), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA) were used to investigate the curing behavior, curing kinetics, dynamic mechanical properties, thermal stability, and impact strength of the prepared copolymers. The kinetic parameters for the P-ddm/APbPc blend curing processes were examined by utilizing the iso-conversional, Flynn–Wall–Ozawa, and Málek methods. The P-ddm/APbPc blends exhibit two typical curing processes, and DSC results confirmed that the blending of APbPc monomer can effectively reduce the curing temperature of P-ddm resin. The autocatalytic models also described the non-isothermal curing reaction rate well, and the appropriate kinetic parameters of the curing process were obtained. The DMA and impact strength experiments proved that the blending of APbPc monomer can significantly improve the toughness and stiffness of P-ddm resin, the highest enhancements were observed on 25 wt.% addition of APbPc, the recorded values for the storage modulus and impact strength were 1003 MPa and 3.60 kJ/m2 higher, respectively, while a decline of 24.6 °C was observed in the glass transition temperature values. TGA curves indicated that the cured copolymers also exhibit excellent thermal stabilities.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Thermal stability and dynamic mechanical behavior of functional multiphase boride ceramics/epoxy composites

2019 ◽  
Vol 39 (6) ◽  
pp. 508-514
Author(s):  
Yannan He ◽  
Zhiqiang Yu
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Element Analysis ◽  
Reaction Heat ◽  
Dynamic Mechanical

Abstract The thermal and dynamic mechanical properties of epoxy composites filled with zirconium diboride/nano-alumina (ZrB2/Al2O3) multiphase particles were investigated by means of differential scanning calorimetry, dynamic thermo-mechanical analysis, and numerical simulation. ZrB2/Al2O3 particles were surface organic functional modified by γ-glycidoxypropyltrimethoxysilane for the improvement of their dispersity in epoxy matrix. The results indicated that the curing exotherm of epoxy resin decreased significantly due to the addition of ZrB2/Al2O3 multiphase particles. In comparison to the composites filled with unmodified particles, the modified multiphase particles made the corresponding filling composites exhibit lower curing reaction heat, lower loss modulus, and higher storage modulus. Generally speaking, the composites filled with 5 wt% modified multiphase particles presented the best thermal stability and thermo-mechanical properties due to the better filler-matrix interfacial compatibility and the uniform dispersity of modified particles. Finite element analysis also suggested that the introduction of modified ZrB2/Al2O3 multiphase particles increased the stiffness of the corresponding composites.

Characterization of PLA/TPU composite filaments manufactured for 3D printing with FDM

2021 ◽  
pp. 089270572110625
Author(s):  
Ajay Jayswal ◽  
Sabit Adanur
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Mechanical Analysis ◽  
Uniaxial Tensile ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
3D Printed

Polylactic acid (PLA) and thermoplastic polyurethane (TPU) were mixed in different proportions and extruded through twin-screw and single-screw extruders to obtain composite filaments to be used for 3D printing with fused deposition modeling (FDM) method. The properties of the filaments were characterized using uniaxial tensile tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), rheology, polarized optical microscope (POM), and scanning electron microscope (SEM). 3D printed samples from composite filaments were tested using dynamic mechanical analysis (DMA). It was found that the tensile strength and modulus of the filaments decrease while elongation at break increases with the increasing TPU content in the composite. The analysis also showed a partial miscibility of the polymer constituents in the solution of composite filaments. Finally, a flexible structure, plain weave fabric, was designed and 3D printed using the composite filaments developed which proved that the filaments are well suited for 3D printing.

The Research of Poly Propylene Carbonate /Nano-SiO2 Composites

2014 ◽  
Vol 904 ◽  
pp. 74-77 ◽  
Author(s):  
Qu Li ◽  
Heng Wu ◽  
Si Yuan Xie ◽  
Jiao Sun ◽  
Xing Hai Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Glass Transition ◽  
Transition Temperature ◽  
Propylene Carbonate ◽  
Tensile Tests ◽  
Slight Improvement ◽  
Biodegradable Poly ◽  
Poly Propylene

Biodegradable poly (propylene carbonate) (PPC) composite with a slight improvement in the thermal stability and tensile strength was successfully prepared by incorporating a low content of nano-SiO2. Tensile tests demonstrate the better mechanical properties of the composites prepared in this study. The obtained composites increases sharply from 1.57Mpa to 12.04Mpa by incorporating 5wt% nano-SiO2. Furthermore, the composites show approximately 8°C higher glass transition temperature (Tg) than that of neat PPC.The Tdmax of composite with 5wt% of nano-SiO2 was about 40°C higher than that of neat PPC.

scholarly journals Self-Healing and Mechanical Properties of Thermoplastic Polyurethane/Eugenol-Based Phenoxy Resin Blends via Exchange Reactions

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1011 ◽  
Author(s):  
Jing-Yu Liang ◽  
Se-Ra Shin ◽  
Soo-Hyoung Lee ◽  
Dai-Soo Lee
Keyword(s):  
Mechanical Properties ◽  
Exchange Reaction ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Resin Content ◽  
Self Healing ◽  
Exchange Reactions ◽  
Scanning Calorimetry ◽  
Healing Efficiency ◽  
Different Types

The possibility of exchange reactions and thermal self-healing in blends of thermoplastic polyurethane (TPU) and phenoxy resin was investigated herein. The analyses were based on characterization obtained via differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), and tensile test. A new phenoxy resin was synthesized from eugenol, and blends with different types of TPU were prepared to investigate the exchange reaction, thermal self-healing, and mechanical properties. The influence of phenoxy resin content on the mechanical behavior and healing efficiency was studied. Improvement of storage modulus owing to the increase of phenoxy resin content was observed. Results suggest that the exchange reaction between phenoxy- and ester-type TPU occurred during thermal treatment. However, little exchange occurred between phenoxy resin and ether-type TPU. Specifically, only ester-type TPU exhibited a significant exchange reaction in the phenoxy resin blend. Furthermore, in the presence of a catalyst (e.g., zinc acetate), the exchange reaction readily occurred, and the healing efficiency improved by the addition of the catalyst and increase in the phenoxy content.

Sign in / Sign up

Export Citation Format

Share Document