scholarly journals Numerical Studies of Disperse Three-Phase Fluid Flows

Fluids ◽  
2021 ◽  
Vol 6 (9) ◽  
pp. 317
Author(s):  
Lei Zeng ◽  
Daniel Velez ◽  
Jiacai Lu ◽  
Gretar Tryggvason
Keyword(s):  
Surface Tension ◽  
Volume Fraction ◽  
Fluid Flows ◽  
Reynolds Numbers ◽  
Unit Cell ◽  
Multiphase System ◽  
Computational Domain ◽  
Numerical Studies ◽  
Three Phase ◽  
Phase Fluid

The dynamics of a three-phase gas–liquid–liquid multiphase system is examined by direct numerical simulations. The system consists of a continuous liquid phase, buoyant gas bubbles, and smaller heavy drops that fall relative to the continuous liquid. The computational domain is fully periodic, and a force equal to the weight of the mixture is added to keep it in place. The governing parameters are selected so that the terminal Reynolds numbers of the bubbles and the drops are moderate; while the effect of bubble deformability is examined by changing its surface tension, the surface tension for the drops is sufficiently high so they do not deform. One bubble in a “unit cell” and eight freely interacting bubbles are examined. The dependency of the slip velocities, the velocity fluctuations, and the distribution of the dispersed phases on the volume fraction of each phase are examined. It is found that while the distribution of drops around a single bubble in a “unit cell” is uneven and depends on its deformability, the distribution of drops around freely interacting bubbles is relatively uniform for the parameters examined in this study.

Eulerian modelling of compressible three-fluid flows with surface tension

2019 ◽  
Vol 34 (4) ◽  
pp. 225-240 ◽  
Author(s):  
Chao Zhang ◽  
Igor Menshov
Keyword(s):  
Surface Tension ◽  
Fluid Flow ◽  
Fluid Model ◽  
Fluid Flows ◽  
Surface Force ◽  
Numerical Approach ◽  
Viscous Effects ◽  
Proposed Model ◽  
Three Phase ◽  
Specific Phase

Abstract The paper addresses a numerical approach for calculating three-fluid hydrodynamics on Eulerian grids with taking into account surface tension and viscous effects. The medium considered consists of three different compressible fluids separated with interfaces. The fluids are assumed to be immiscible. The three-fluid flow is described by the reduced equilibrium model derived from the non-equilibrium three-phase model by performing an asymptotic analysis in the limit of zero relaxation time. To simulate surface tension effects, we extend the continuum surface force (CSF) model of two-fluid incompressible flow to the case of compressible three-fluid flow. A thermodynamically consistent surface energy of the compressible three-fluid flow is obtained by means of splitting the surface tension between distinct fluids into pairs of specific phase related surface tensions. Some aspects of the numerical method for solving the system of governing equations of the considered three-fluid model are discussed. Numerical results presented demonstrate the accuracy and robustness of the proposed model in simulating dynamics of interfaces and surface tension effects.

scholarly journals Effect of the Preheated Oxidizer Temperature on Soot Formation and Flame Structure in Turbulent Methane-Air Diffusion Flames at 1 and 3 atm: A CFD Investigation

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3671
Author(s):  
Subrat Garnayak ◽  
Subhankar Mohapatra ◽  
Sukanta K. Dash ◽  
Bok Jik Lee ◽  
V. Mahendra Reddy
Keyword(s):  
Mole Fraction ◽  
Air Temperature ◽  
Reaction Rate ◽  
Volume Fraction ◽  
Diffusion Flames ◽  
Soot Formation ◽  
Flame Structure ◽  
Soot Volume Fraction ◽  
Computational Domain ◽  
Pressure Elevation

This article presents the results of computations on pilot-based turbulent methane/air co-flow diffusion flames under the influence of the preheated oxidizer temperature ranging from 293 to 723 K at two operating pressures of 1 and 3 atm. The focus is on investigating the soot formation and flame structure under the influence of both the preheated air and combustor pressure. The computations were conducted in a 2D axisymmetric computational domain by solving the Favre averaged governing equation using the finite volume-based CFD code Ansys Fluent 19.2. A steady laminar flamelet model in combination with GRI Mech 3.0 was considered for combustion modeling. A semi-empirical acetylene-based soot model proposed by Brookes and Moss was adopted to predict soot. A careful validation was initially carried out with the measurements by Brookes and Moss at 1 and 3 atm with the temperature of both fuel and air at 290 K before carrying out further simulation using preheated air. The results by the present computation demonstrated that the flame peak temperature increased with air temperature for both 1 and 3 atm, while it reduced with pressure elevation. The OH mole fraction, signifying reaction rate, increased with a rise in the oxidizer temperature at the two operating pressures of 1 and 3 atm. However, a reduced value of OH mole fraction was observed at 3 atm when compared with 1 atm. The soot volume fraction increased with air temperature as well as pressure. The reaction rate by soot surface growth, soot mass-nucleation, and soot-oxidation rate increased with an increase in both air temperature and pressure. Finally, the fuel consumption rate showed a decreasing trend with air temperature and an increasing trend with pressure elevation.

Volume preserving immersed boundary methods for two-phase fluid flows

2011 ◽  
Vol 69 (4) ◽  
pp. 842-858 ◽  
Author(s):  
Yibao Li ◽  
Eunok Jung ◽  
Wanho Lee ◽  
Hyun Geun Lee ◽  
Junseok Kim
Keyword(s):  
Fluid Flows ◽  
Immersed Boundary ◽  
Immersed Boundary Methods ◽  
Two Phase ◽  
Boundary Methods ◽  
Phase Fluid ◽  
Volume Preserving

scholarly journals Turbulence Intensity Modulation by Micropolar Fluids

Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 195
Author(s):  
George Sofiadis ◽  
Ioannis Sarris
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Fluid Flows ◽  
Turbulent Channel Flow ◽  
High Volume ◽  
Reynolds Numbers ◽  
Intensity Modulation ◽  
Wall Turbulence ◽  
Volume Fractions ◽  
Physical Phenomena

Fluid microstructure nature has a direct effect on turbulence enhancement or attenuation. Certain classes of fluids, such as polymers, tend to reduce turbulence intensity, while others, like dense suspensions, present the opposite results. In this article, we take into consideration the micropolar class of fluids and investigate turbulence intensity modulation for three different Reynolds numbers, as well as different volume fractions of the micropolar density, in a turbulent channel flow. Our findings support that, for low micropolar volume fractions, turbulence presents a monotonic enhancement as the Reynolds number increases. However, on the other hand, for sufficiently high volume fractions, turbulence intensity drops, along with Reynolds number increment. This result is considered to be due to the effect of the micropolar force term on the flow, suppressing near-wall turbulence and enforcing turbulence activity to move further away from the wall. This is the first time that such an observation is made for the class of micropolar fluid flows, and can further assist our understanding of physical phenomena in the more general non-Newtonian flow regime.

scholarly journals Application of Artificial Intelligence and Gamma Attenuation Techniques for Predicting Gas–Oil–Water Volume Fraction in Annular Regime of Three-Phase Flow Independent of Oil Pipeline’s Scale Layer

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1460
Author(s):  
Abdulaziz S. Alkabaa ◽  
Ehsan Nazemi ◽  
Osman Taylan ◽  
El Mostafa Kalmoun
Keyword(s):  
Gamma Radiation ◽  
Volume Fraction ◽  
Phase Flow ◽  
Gas Oil ◽  
Oil Pipeline ◽  
Intelligent Technique ◽  
Scale Layer ◽  
Three Phase ◽  
Three Phase Flow ◽  
Annular Regime

To the best knowledge of the authors, in former studies in the field of measuring volume fraction of gas, oil, and water components in a three-phase flow using gamma radiation technique, the existence of a scale layer has not been considered. The formed scale layer usually has a higher density in comparison to the fluid flow inside the oil pipeline, which can lead to high photon attenuation and, consequently, reduce the measuring precision of three-phase flow meter. The purpose of this study is to present an intelligent gamma radiation-based, nondestructive technique with the ability to measure volume fraction of gas, oil, and water components in the annular regime of a three-phase flow independent of the scale layer. Since, in this problem, there are several unknown parameters, such as gas, oil, and water components with different amounts and densities and scale layers with different thicknesses, it is not possible to measure the volume fraction using a conventional gamma radiation system. In this study, a system including a 241Am-133Ba dual energy source and two transmission detectors was used. The first detector was located diametrically in front of the source. For the second detector, at first, a sensitivity investigation was conducted in order to find the optimum position. The four extracted signals in both detectors (counts under photo peaks of both detectors) were used as inputs of neural network, and volume fractions of gas and oil components were utilized as the outputs. Using the proposed intelligent technique, volume fraction of each component was predicted independent of the barium sulfate scale layer, with a maximum MAE error of 3.66%.

Lattice-Boltzmann Simulation of Two-Phase Fluid Flows

1998 ◽  
Vol 09 (08) ◽  
pp. 1383-1391 ◽  
Author(s):  
Yu Chen ◽  
Shulong Teng ◽  
Takauki Shukuwa ◽  
Hirotada Ohashi
Keyword(s):  
Lattice Boltzmann ◽  
Fluid Flows ◽  
Navier Stokes ◽  
Interface Model ◽  
Two Phase ◽  
Navier Stokes Equation ◽  
Lattice Boltzmann Simulation ◽  
Dam Breaking ◽  
Volumetric Stress ◽  
Phase Fluid

A model with a volumetric stress tensor added to the Navier–Stokes Equation is used to study two-phase fluid flows. The implementation of such an interface model into the lattice-Boltzmann equation is derived from the continuous Boltzmann BGK equation with an external force term, by using the discrete coordinate method. Numerical simulations are carried out for phase separation and "dam breaking" phenomena.

The Influence of Multiple Inclusions on the Cauchy Stress of a Spherical Particle-Reinforced Composite Under Uniaxial Loading

2014 ◽  
Author(s):  
Ke Niu ◽  
Armin Abedini ◽  
Zengtao Chen
Keyword(s):  
Spherical Particle ◽  
Single Particle ◽  
Volume Fraction ◽  
Unit Cell ◽  
Spherical Particles ◽  
Uniaxial Tensile ◽  
Cauchy Stress ◽  
Particle Volume ◽  
Volume Fractions ◽  
Unit Cells

This paper investigates the influence of multiple inclusions on the Cauchy stress of a spherical particle-reinforced metal matrix composite (MMC) under uniaxial tensile loading condition. The approach of three-dimensional cubic multi-particle unit cell is used to investigate the 15 non-overlapping identical spherical particles which are randomly distributed in the unit cell. The coordinates of the center of each particle are calculated by using the Random Sequential Adsorption algorithm (RSA) to ensure its periodicity. The models with reinforcement volume fractions of 10%, 15%, 20% and 25% are evaluated by using the finite element method. The behaviour of Cauchy stress for each model is analyzed at a far-field strain of 5%. For each reinforcement volume fraction, four models with different particle spatial distributions are evaluated and averaged to achieve a more accurate result. At the same time, single-particle unit cell and analytical model were developed. The stress-strain curves of multi-particle unit cells are compared with single-particle unit cells and the tangent homogenization model coupled with the Mori-Tanaka method. Only little scatters were found between unit cells with the same particle volume fractions. Multi-particle unit cells predict higher response than single particle unit cells. As the volume fraction of reinforcements increases, the Cauchy stress of MMCs increases.

Sign in / Sign up

Export Citation Format

Share Document