scholarly journals Numerical Analysis for Heat Transfer Augmentation in a Circular Tube Heat Exchanger Using a Triangular Perforated Y-Shaped Insert

Fluids ◽  
2021 ◽  
Vol 6 (7) ◽  
pp. 247
Author(s):  
Lokesh Pandey ◽  
Satyendra Singh
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Circular Tube ◽  
Tube Wall ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Heat Transfer Augmentation ◽  
Plain Tube

The present investigation constitutes CFD analysis of the heat transmission phenomenon in a tube heat exchanger with a Y-shaped insert with triangular perforation. The analysis is accomplished by considering air as a working fluid with a Reynolds number ranging from 3000 to 21,000. The segment considered for analysis consists of a circular tube of 68 mm diameter and 1.5 m length. The geometrical parameter considered is the perforation index (0%, 10%, 20%, and 30%). The constant heat flux is provided at the tube wall and a pressure-based solver is used for the solution. The studies are performed for analyzing the effects of inserts on the heat transfer and friction factor in the circular tube heat exchanger which results in augmented heat transfer at a higher perforation index (PI) and lower friction factor. The investigation results show that the highest heat transfer is 5.84 times over a simple plain tube and the maximum thermal performance factor (TPF) is 3.25 at PI = 30%, Re = 3000.

Numerical investigation of Heat Transfer Enhancement in Circular Tube using Twisted Tape Inserts and Nanotechnology

2017 ◽  
Vol 5 (2) ◽  
pp. 42-54
Author(s):  
Najim Abid Jassim ◽  
Kamel Abdul Hussin ◽  
Noor Yahya Abdul Abbass
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Chemical Engineering ◽  
Working Fluid ◽  
Width Ratio ◽  
Twisted Tape ◽  
Tube Heat Exchanger ◽  
First Case ◽  
Plain Tube ◽  
Shell And Tube

In the present work the analysis of three different width ratio of twisted tape in a shell and tube heat exchanger done by ANSYS FLUINT14.0. Heat exchanger type shell and tube have been widely used in industrial application such as refrigeration and environment protection, electrical power generation and chemical engineering. This work deals with the theoretical investigation, which was to evaluate the benefit of changing the width of twisted tape in the heat exchanger and the improving the heat transfer by using water as the working fluid in the first case, then using Nano fluids as a heat transfer working fluid. From the use of the condition in table (1) the simulation shows results of enhancement in heat transfer rate ranging from (53.24% to 55.55%) at width ratio 0.71, (53.62% to 56.09%) at width ratio 0.854 and (52.44% to 57.17%) at width ratio 1, for plain tube with twisted tape with respect to plain tube without twisted tape by using water as cooling fluid. By using Nano- fluid (AL2O3) the enhancement in heat transfer is (69.14% to 60.44%) at width ratio 0.71, (58.36% to 61.51%) at width ratio 0.854 and (56.76% to 63.35%) at width ratio1, for plain tube with twisted tape with respect to plain tube without twisted tape.

Heat Transfer Enhancement in a Double Pipe Heat Exchanger by Insertion of Propeller-Type Swirl Generators

2010 ◽  
Author(s):  
Khwanchit Wongcharee ◽  
Somsak Pethkool ◽  
Chinaruk Thianpong
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Operating Conditions ◽  
Interval Length ◽  
Tube Heat Exchanger ◽  
Nusselt Numbers ◽  
Plain Tube

This paper describes an experimental study of turbulent convective heat transfer and flow friction characteristics in a double tube heat exchanger equipped with propellers (2 blade-type). The propellers are used as the decaying swirl generators in the inner tube. The experiments were performed using the propellers with four different interval lengths (l = 1D, 2D, 3D and 4D where D is diameter of the inner tube), for the Reynolds number ranging from 5000 to 32,000, using water with temperature of 27°C and 70°C as cold and hot working fluids, respectively. The data of the tube equipped with the propellers are reported together with those of the plain tube, for comparison. The obtained results demonstrate that the heat transfer rate in term of Nusselt number (Nu) and friction factor (f) in the tube with propellers are higher than those in the plain tube at the similar operating conditions. This is due to the chaotic mixing and efficient interruption of thermal boundary layer caused by the propellers. In addition, the Nusselt number and friction factor in the tube fitted with the propellers increase as the interval length decreases. Depending on Reynolds number and interval length, Nusselt numbers and friction factors in the tube fitted with the propellers are augmented to 1.95 to 2.3 times and 5.8 to 13.2 times of those in the plain tube. In addition, the correlations of the Nusselt number (Nu) and the friction factor (f) for tube fitted with the propellers are reported and the performance evaluation to access the real benefits of using the turbulators is also determined.

Experimental Investigations on Heat Transfer Enhancement in a Horizontal Tube Using Converging and Diverging Conical Strips

2014 ◽  
Author(s):  
Naga Sarada Somanchi ◽  
Sri Rama Devi Rangisetty ◽  
Sudheer PremKumar Bellam ◽  
Ravi Gugulothu ◽  
Samuel Bellam
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Circular Tube ◽  
Horizontal Tube ◽  
Working Fluid ◽  
Experimental Investigations ◽  
Transfer Enhancement ◽  
Enhancement Of Heat Transfer ◽  
Plain Tube ◽  
Flow Heat

The present work deals with the results of the experimental investigations carried out on augmentation of turbulent flow heat transfer in a horizontal circular tube by means of tube inserts, with air as working fluid. Experiments were carried out initially for the plain tube (without tube inserts). The Nusselt number and friction factor obtained experimentally were validated against those obtained from theoretical correlations. Secondly experimental investigations using six kinds of tube inserts namely Rectangular bar with diverging conical strips, Rectangular bar with converging conical strips, Rectangular bar with alternate converging diverging conical strips, Rectangular bar with holes and diverging conical strips, Rectangular bar with holes and converging conical strips and Rectangular bar with holes and alternate converging diverging conical strips were carried out to estimate the enhancement of heat transfer rate for air in the presence of inserts. The Reynolds number ranged from 8000 to 19000. In the presence of inserts, Nusselt number and pressure drop increased, overall enhancement ratio is calculated to determine the optimum geometry of the tube insert. Based on experimental investigations, it is observed that, the enhancement of heat transfer using Rectangular bar with diverging conical strips is more effective compared to other inserts.

Shell-and-Tube Side Heat Transfer Augmentation by the Use of Wall Radiation in a Crossflow Shell-and-Tube Heat Exchanger

1984 ◽  
Vol 106 (4) ◽  
pp. 735-742 ◽  
Author(s):  
Y. Yamada ◽  
M. Akai ◽  
Y. Mori
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Room Temperature ◽  
Heat Transfer Performance ◽  
Transfer Coefficients ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Heat Transfer Augmentation ◽  
Hot Gas ◽  
Shell And Tube

The heat transfer performance of a crossflow shell-and-tube heat exchanger for high-temperature use in which heat transfer is augmented by the use of wall radiation in both shell and tube sides, is studied. Radiation plates are inserted in the shell side, and twisted cross-tapes in the tube side. Overall heat transfer coefficients are measured to be about a maximum 80 percent larger than those without radiation, where the inlet temperatures of the hot gas range up to 800 °C, while those of the cold gas are about room temperature. Analytical results agree well with experimental results, and an approximate calculation procedure is found to be simple and accurate enough for practical use.

scholarly journals Heat transfer performance and friction factor of various nanofluids in a double-tube counter flow heat exchanger

2020 ◽  
Vol 24 (6 Part A) ◽  
pp. 3601-3612
Author(s):  
Dan Zheng ◽  
Jin Wang ◽  
Yu Pang ◽  
Zhanxiu Chen ◽  
Bengt Sunden
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Flow Resistance ◽  
Heat Transfer Performance ◽  
Weight Fraction ◽  
Transfer Performance ◽  
Tube Heat Exchanger ◽  
High Heat Transfer

Experimental research was conducted to reveal the effects of nanofluids on heat transfer performance in a double-tube heat exchanger. With nanoparticle weight fraction of 0.5-2.0% and Reynolds number of 4500-14500, the flow resistance and heat transfer were analyzed by using six nanofluids, i.e., CuO-water, Al2O3-water, Fe3O4-water, ZnO-water, SiC-water, SiO2-water nanofluids. Results show that SiC-water nanofluid with a weight concentration of 1.5% provides the best improvement of heat transfer performance. 1.0% CuO-water and 0.5% SiO2-water nanofluids have lower friction factors in the range of Reynolds number from 4500-14500 compared to the other nanofluids. Based on test results of heat transfer performance and flow resistance, the 1.0% CuO-water nanofluid shows a great advantage due to a relatively high heat transfer performance and a low friction factor. Finally, empirical formulae of Nusselt numbers for various nanofluids were established based on experimental data tested in the double-tube heat exchanger.

scholarly journals Enhancing Heat Transfer in Tube Heat Exchanger by Inserting Discrete Twisting Tapes with Different Positions

2019 ◽  
Vol 25 (8) ◽  
pp. 39-51
Author(s):  
Nassr Fadhil Hussein ◽  
Abdulrahman Shakir Mahmood
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Constant Heat Flux ◽  
Vertical Position ◽  
Maximum Heat ◽  
Tube Heat Exchanger ◽  
Twisted Tapes ◽  
Maximum Heat Transfer

Enhancement of heat transfer in the tube heat exchanger is studied experimentally by using discrete twisted tapes. Three different positions were selected for inserting turbulators along tube section (horizontal position by α= 00, inclined position by α= 45 0 and vertical position by α= 900). The space between turbulators was fixed by distributing 5 pieces of these turbulators with pitch ratio    PR = (0.44). Also, the factor of constant heat flux was applied as a boundary condition around the tube test section for all experiments of this investigation, while the flow rates were selected as a variable factor (Reynolds number values vary from 5000 to 15000). The results show that using discrete twisted tapes enhances the heat transfer rate by about 60.7-103.7 % compared with plane tube case. Also, inserting turbulators with inclined position offers maximum heat transfer rate by 103.7%.  

Numerical Study of Flow and Heat Transfer Enhancement by Using Delta Winglets in a Triangular Wavy Fin-and-Tube Heat Exchanger

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Liting Tian ◽  
Yaling He ◽  
Pan Chu ◽  
Wenquan Tao
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Numerical Study ◽  
Attack Angle ◽  
Geometrical Parameters ◽  
Tube Heat Exchanger ◽  
Delta Winglet

In this paper, three-dimensional numerical simulations with renormalization-group (RNG) k-ε model are performed for the air-side heat transfer and fluid flow characteristics of wavy fin-and-tube heat exchanger with delta winglet vortex generators. The Reynolds number based on the tube outside diameter varies from 500 to 5000. The effects of different geometrical parameters with varying attack angle of delta winglet (β=30 deg, β=45 deg, and β=60 deg), tube row number (2–4), and wavy angle of the fin (θ=0–20 deg) are examined. The numerical results show that each delta winglet generates a downstream main vortex and a corner vortex. The longitudinal vortices are disrupted by the downstream wavy trough and only propagate a short distance along the main flow direction but the vortices greatly enhance the heat transfer in the wake region behind the tube. Nusselt number and friction factor both increase with the increase in the attack angle β, and the case of β=30 deg has the maximum value of j/f. The effects of the tube row number on Nusselt number and friction factor are very small, and the heat transfer and fluid flow become fully developed very quickly. The case of θ=5 deg has the minimum value of Nusselt number, while friction factor always increases with the increase in wavy angle. The application of delta winglet enhances the heat transfer performance of the wavy fin-and-tube heat exchanger with modest pressure drop penalty.

scholarly journals Obtaining Closure for Fin-and-Tube Heat Exchanger Modeling Based on Volume Averaging Theory (VAT)

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
Feng Zhou ◽  
Nicholas E. Hansen ◽  
David J. Geb ◽  
Ivan Catton
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Volume Averaging ◽  
Averaging Theory ◽  
Length Scale ◽  
Tube Heat Exchanger ◽  
Volume Averaging Theory

Modeling a fin-and-tube heat exchanger as porous media based on volume averaging theory (VAT), specific geometry can be accounted for in such a way that the details of the original structure can be replaced by their averaged counterparts, and the VAT based governing equations can be solved for a wide range of heat exchanger designs. To complete the VAT based model, proper closure is needed, which is related to a local friction factor and a heat transfer coefficient of a representative elementary volume. The present paper describes an effort to model a fin-and-tube heat exchanger based on VAT and obtain closure for the model. Experiment data and correlations for the air side characteristics of fin-and-tube heat exchangers from the published literature were collected and rescaled using the “porous media” length scale suggested by VAT. The results were surprisingly good, collapsing all the data onto a single curve for friction factor and Nusselt number, respectively. It was shown that using the porous media length scale is very beneficial in collapsing complex data yielding simple heat transfer and friction factor correlations and that by proper scaling, closure is a function of the porous media, which further generalizes macroscale porous media equations. The current work is a step closer to our final goal, which is to develop a universal fast running computational tool for multiple-parameter optimization of heat exchangers.

Sign in / Sign up

Export Citation Format

Share Document