scholarly journals Thermo-Environmental Performance of Four Different Shapes of Solar Greenhouse Dryer with Free Convection Operating Principle and No Load on Product

Fluids ◽  
2021 ◽  
Vol 6 (5) ◽  
pp. 183
Author(s):  
Edwin Villagran ◽  
Juan Camilo Henao-Rojas ◽  
German Franco
Keyword(s):  
Environmental Performance ◽  
Three Dimensional ◽  
Climatic Conditions ◽  
Aromatic Plants ◽  
Mentha Spicata ◽  
Precise Tool ◽  
Computational Fluid Dynamics Cfd ◽  
Different Shapes ◽  
Viable Method ◽  
Real Scale

Solar drying using greenhouse dryers is a viable method from the technical, economic, and environmental perspectives, allowing the drying of agricultural products for conservation purposes in different regions of the world. In Colombia, the drying of aromatic plants such as mint (Mentha spicata) is usually done directly and in open fields, which exposes the product to contamination and loss of quality. Therefore, the objective of this research was to use a three-dimensional computational fluid dynamics (CFD-3D) model previously successfully validated and implemented in this work to study the performance of air flow patterns, temperature, and humidity inside four greenhouse-type dryers contemplated for a region with hot and humid climatic conditions. The results found allowed us to observe that the spatial distribution of temperature and relative humidity are related to the air flows generated inside each dryer, therefore, there were differences of up to 7.91 °C and 23.81% for the same evaluated scenario. The study also allowed us to conclude that the CFD methodology is an agile and precise tool that allows us to evaluate prototypes that have not been built to real scale, which allows us to generate useful information for decision-making regarding the best prototype to build under a specific climate condition.

Improvement of real-scale raceway bioreactors for microalgae production using Computational Fluid Dynamics (CFD)

2021 ◽  
Vol 54 ◽  
pp. 102207
Author(s):  
Cristian Inostroza ◽  
Alessandro Solimeno ◽  
Joan García ◽  
José M. Fernández-Sevilla ◽  
F. Gabriel Acién
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Computational Fluid Dynamics Cfd ◽  
Real Scale

scholarly journals Impact of Orifice-to-Pipe Diameter Ratio on Leakage Flow: An Experimental Study

Water ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 2189
Author(s):  
Tingchao Yu ◽  
Xiangqiu Zhang ◽  
Iran E. Lima Neto ◽  
Tuqiao Zhang ◽  
Yu Shao ◽  
...  
Keyword(s):  
Experimental Study ◽  
Flow Rate ◽  
Pipe Wall ◽  
Pressure Head ◽  
Diameter Ratio ◽  
Pipe Diameter ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Different Shapes ◽  
Real Scale

The traditional orifice discharge formula used to estimate the flow rate through a leak opening at a pipe wall often produces inaccurate results. This paper reports an original experimental study in which the influence of orifice-to-pipe diameter ratio on leakage flow rate was investigated for several internal/external flow conditions and orifice holes with different shapes. The results revealed that orifice-to-pipe diameter ratio (or pipe wall curvature) indeed influenced the leakage flow, with the discharge coefficient ( C d ) presenting a wide variation (0.60–0.85). As the orifice-to-pipe diameter ratio decreased, the values of C d systematically decreased from about 12% to 3%. Overall, the values of C d also decreased with β (ratio of pressure head differential at the orifice to wall thickness), as observed in previous studies. On the other hand, orifice shape, main pipe flow velocity, and external medium (water or air) all had a secondary effect on C d . The results obtained in the present study not only demonstrated that orifice-to-pipe diameter ratio affects the outflow, but also that real scale pipes may exhibit a relevant deviation of C d from the classical range (0.61–0.67) reported in the literature.

Assessment of Unsteady Flows in Turbines

1992 ◽  
Vol 114 (1) ◽  
pp. 79-90 ◽  
Author(s):  
O. P. Sharma ◽  
G. F. Pickett ◽  
R. H. Ni
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Experimental Investigations ◽  
Flow Parameters ◽  
Research Activities ◽  
Flow Features ◽  
Computational Fluid Dynamics Cfd ◽  
Turbine Design ◽  
The Impact

The impacts of unsteady flow research activities on flow simulation methods used in the turbine design process are assessed. Results from experimental investigations that identify the impact of periodic unsteadiness on the time-averaged flows in turbines and results from numerical simulations obtained by using three-dimensional unsteady Computational Fluid Dynamics (CFD) codes indicate that some of the unsteady flow features can be fairly accurately predicted. Flow parameters that can be modeled with existing steady CFD codes are distinguished from those that require unsteady codes.

The Effect of Bench Arrangements on the Natural Ventilation of a Multispan Greenhouse

2013 ◽  
Author(s):  
Sunita Kruger ◽  
Leon Pretorius
Keyword(s):  
Fluid Dynamics ◽  
Natural Ventilation ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Low Velocity ◽  
Lower Velocity ◽  
Cfd Models ◽  
Temperature Distributions ◽  
Computational Fluid Dynamics Cfd ◽  
Plant Level

In this paper, the influence of various bench arrangements on the microclimate inside a two-span greenhouse is numerically investigated using three-dimensional Computational Fluid Dynamics (CFD) models. Longitudinal and peninsular arrangements are investigated for both leeward and windward opened roof ventilators. The velocity and temperature distributions at plant level (1m) were of particular interest. The research in this paper is an extension of two-dimensional work conducted previously [1]. Results indicate that bench layouts inside the greenhouse have a significant effect on the microclimate at plant level. It was found that vent opening direction (leeward or windward) influences the velocity and temperature distributions at plant level noticeably. Results also indicated that in general, the leeward facing greenhouses containing either type of bench arrangement exhibit a lower velocity distribution at plant level compared to windward facing greenhouses. The latter type of greenhouses has regions with relatively high velocities at plant level which could cause some concern. The scalar plots indicate that more stagnant areas of low velocity appear for the leeward facing greenhouses. The windward facing greenhouses also display more heterogeneity at plant level as far as temperature is concerned.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

scholarly journals Three-Dimensional Navier–Stokes Analysis and Redesign of an Imbedded Bellmouth Nozzle in a Turbine Cascade Inlet Section

1996 ◽  
Vol 118 (3) ◽  
pp. 529-535 ◽  
Author(s):  
P. W. Giel ◽  
J. R. Sirbaugh ◽  
I. Lopez ◽  
G. J. Van Fossen
Keyword(s):  
Three Dimensional ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Inlet Section ◽  
Turbine Cascade ◽  
Blade Cascade ◽  
Inlet Geometry ◽  
Computational Fluid Dynamics Cfd ◽  
Transonic Turbine ◽  
Flow Nonuniformity

Experimental measurements in the inlet of a transonic turbine blade cascade showed unacceptable pitchwise flow nonuniformity. A three-dimensional, Navier–Stokes computational fluid dynamics (CFD) analysis of the imbedded bellmouth inlet in the facility was performed to identify and eliminate the source of the flow nonuniformity. The blockage and acceleration effects of the blades were accounted for by specifying a periodic static pressure exit condition interpolated from a separate three-dimensional Navier–Stokes CFD solution of flow around a single blade in an infinite cascade. Calculations of the original inlet geometry showed total pressure loss regions consistent in strength and location to experimental measurements. The results indicate that the distortions were caused by a pair of streamwise vortices that originated as a result of the interaction of the flow with the imbedded bellmouth. Computations were performed for an inlet geometry that eliminated the imbedded bellmouth by bridging the region between it and the upstream wall. This analysis indicated that eliminating the imbedded bellmouth nozzle also eliminates the pair of vortices, resulting in a flow with much greater pitchwise uniformity. Measurements taken with an installed redesigned inlet verify that the flow nonuniformity has indeed been eliminated.

scholarly journals Learning Human Anatomy Using Three-Dimensional Models Made from Real-Scale Bone Pieces: Experience with the Knee Joint among Pre-Service Biology Teachers

2015 ◽  
Vol 33 (4) ◽  
pp. 1299-1306 ◽  
Author(s):  
Pablo A Lizana ◽  
Cristian Merino ◽  
Arlette Bassaber ◽  
Ricardo Henríquez ◽  
G Vega-Fernández ◽  
...  
Keyword(s):  
Knee Joint ◽  
Three Dimensional ◽  
Human Anatomy ◽  
Biology Teachers ◽  
Dimensional Models ◽  
Three Dimensional Models ◽  
Real Scale

Fully Coupled Three-Dimensional Dynamic Response of a TLP Floating Wind Turbine in Waves and Wind

2012 ◽  
Author(s):  
G. K. V. Ramachandran ◽  
H. Bredmose ◽  
J. N. Sørensen ◽  
J. J. Jensen
Keyword(s):  
Wind Turbine ◽  
Dynamic Model ◽  
Three Dimensional ◽  
Geographic Location ◽  
Climatic Conditions ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Total System ◽  
Wave Loads ◽  
Aerodynamic Loads

A dynamic model for a tension-leg platform (TLP) floating offshore wind turbine is proposed. The model includes three-dimensional wind and wave loads and the associated structural response. The total system is formulated using 17 degrees of freedom (DOF), 6 for the platform motions and 11 for the wind turbine. Three-dimensional hydrodynamic loads have been formulated using a frequency- and direction-dependent spectrum. While wave loads are computed from the wave kinematics using Morison’s equation, aerodynamic loads are modelled by means of unsteady Blade-Element-Momentum (BEM) theory, including Glauert correction for high values of axial induction factor, dynamic stall, dynamic wake and dynamic yaw. The aerodynamic model takes into account the wind shear and turbulence effects. For a representative geographic location, platform responses are obtained for a set of wind and wave climatic conditions. The platform responses show an influence from the aerodynamic loads, most clearly through a quasi-steady mean surge and pitch response associated with the mean wind. Further, the aerodynamic loads show an influence from the platform motion through more fluctuating rotor loads, which is a consequence of the wave-induced rotor dynamics. In the absence of a controller scheme for the wind turbine, the rotor torque fluctuates considerably, which induces a growing roll response especially when the wind turbine is operated nearly at the rated wind speed. This can be eliminated either by appropriately adjusting the controller so as to regulate the torque or by optimizing the floater or tendon dimensions, thereby limiting the roll motion. Loads and coupled responses are predicted for a set of load cases with different wave headings. Based on the results, critical load cases are identified and discussed. As a next step (which is not presented here), the dynamic model for the substructure is therefore being coupled to an advanced aero-elastic code Flex5, Øye (1996), which has a higher number of DOFs and a controller module.

Inverse Design of 3D Multi-Stage Transonic Fans at Dual Operating Points

2013 ◽  
Author(s):  
James H. Page ◽  
Paul Hield ◽  
Paul G. Tucker
Keyword(s):  
Design Method ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Inverse Design ◽  
Flow Angle ◽  
Trade Offs ◽  
Multi Stage ◽  
Full Speed ◽  
Computational Fluid Dynamics Cfd ◽  
Operating Points

Semi-inverse design is the automatic re-cambering of an aerofoil, during a computational fluid dynamics (CFD) calculation, in order to achieve a target lift distribution while maintaining thickness, hence “semi-inverse”. In this design method, the streamwise distribution of curvature is replaced by a stream-wise distribution of lift. The authors have developed an inverse design code based on the method of Hield (2008) which can rapidly design three-dimensional fan blades in a multi-stage environment. The algorithm uses an inner loop to design to radially varying target lift distributions, an outer loop to achieve radial distributions of stage pressure ratio and exit flow angle, and a choked nozzle to set design mass flow. The code is easily wrapped around any CFD solver. In this paper, we describe a novel algorithm for designing simultaneously for specified performance at full speed and peak efficiency at part speed, without trade-offs between the targets at each of the two operating points. We also introduce a novel adaptive target lift distribution which automatically develops discontinuous changes of calculated magnitude, based on the passage shock, eliminating erroneous lift demands in the shock vicinity and maintaining a smooth aerofoil.

Sign in / Sign up

Export Citation Format

Share Document