scholarly journals Investigation of High Lift Force Generation of Dragonfly Wing by a Novel Advanced Mode in Hover

Fluids ◽  
2020 ◽  
Vol 5 (2) ◽  
pp. 59
Author(s):  
Xiaohui Su ◽  
Kaixuan Zhang ◽  
Juan Zheng ◽  
Yong Zhao ◽  
Ruiqi Han ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Expenditure ◽  
Lift Force ◽  
Lift Coefficient ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Force Generation ◽  
High Lift ◽  
Dragonfly Wing ◽  
Symmetrical Mode

In the paper, a novel flapping mode is presented that can generate high lift force by a dragonfly wing in hover. The new mode, named partial advanced mode (PAM), starts pitching earlier than symmetric rotation during the downstroke cycle of the hovering motion. As a result, high lift force can be generated due to rapid pitching coupling with high flapping velocity in the stroke plane. Aerodynamic performance of the new mode is investigated thoroughly using numerical simulation. The results obtained show that the period-averaged lift coefficient, CL, increases up to 16% compared with that of the traditional symmetrical mode when an earlier pitching time is set to 8% of the flapping period. The reason for the high lift force generation mechanism is explained in detail using not only force investigation, but also by analyzing vortices produced around the wing. The proposed PAM is believed to lengthen the dynamic stall mechanism and enhance the LEV generated during the downstroke. The improvement of lift force could be considered as a result of a combination of the dynamic stall mechanism and rapid pitch mechanism. Finally, the energy expenditure of the new mode is also analyzed.

scholarly journals COMPUTATIONAL FLUID DYNAMICS STUDY OF DUSTY AIR FLOW OVER NACA 63415 AIRFOIL FOR WIND TURBINE APPLICATIONS

2017 ◽  
Vol 79 (7-3) ◽  
Author(s):  
Iham F. Zidane ◽  
Khalid M. Saqr ◽  
Greg Swadener ◽  
Xianghong Ma ◽  
Mohamed F. Shehadeh
Keyword(s):  
Numerical Simulation ◽  
Wind Turbine ◽  
South African ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Performance ◽  
Accurate Estimation ◽  
African Countries ◽  
Sand Particles

Gulf and South African countries have enormous potential for wind energy. However, the emergence of sand storms in this region postulates performance and reliability challenges on wind turbines. This study investigates the effects of debris flow on wind turbine blade performance. In this paper, two-dimensional incompressible Navier-Stokes equations and the transition SST turbulence model are used to analyze the aerodynamic performance of NACA 63415 airfoil under clean and sandy conditions. The numerical simulation of the airfoil under clean surface condition is performed at Reynolds number 460×103, and the numerical results have a good consistency with the experimental data. The Discrete Phase Model has been used to investigate the role sand particles play in the aerodynamic performance degradation. The pressure and lift coefficients of the airfoil have been computed under different sand particles flow rates. The performance of the airfoil under different angle of attacks has been studied. Results showed that the blade lift coefficient can deteriorate by 28% in conditions relevant to the Gulf and South African countries sand storms. As a result, the numerical simulation method has been verified to be economically available for accurate estimation of the sand particles effect on the wind turbine blades.

scholarly journals Numerical simulation of wind loads on an offshore PV panel: the effect of wave angle

2020 ◽  
Vol 37 ◽  
pp. 53-62
Author(s):  
Kao-Chun Su ◽  
Ping-Han Chung ◽  
Ray-Yeng Yang
Keyword(s):  
Numerical Simulation ◽  
Marine Environment ◽  
Structural Design ◽  
Lift Force ◽  
Lift Coefficient ◽  
Wind Loads ◽  
Angle Of Incidence ◽  
Initial Angle ◽  
Pv Panel ◽  
Wave Angle

ABSTRACT This numerical simulation determines the wind loads on a stand-alone solar panel in a marine environment. The initial angle of tilt is 20° and 40° and the wind is incident at an angle of 0–180° (in increments of 45°). The wave angle affects the motion of a pontoon. For a wave angle of 0–180° (in increments of 45°), the variation in the surface pressure pattern and the lift coefficient with the angle of incidence of wind and waves in a single period is determined. The lift force is determined by competing the tilt angle for the upper surface with respect to wind and variation in roll angle for a specific wave angle. The data are pertinent to structural design for photovoltaic systems in a marine environment.

Scaling law for the lift force of autorotating falling seeds at terminal velocity

2017 ◽  
Vol 835 ◽  
pp. 406-420 ◽  
Author(s):  
Injae Lee ◽  
Haecheon Choi
Keyword(s):  
Numerical Simulation ◽  
Lift Force ◽  
Lift Coefficient ◽  
Scaling Law ◽  
Leading Edge ◽  
Terminal Velocity ◽  
Leading Edge Vortex ◽  
Actuator Disk ◽  
Vortex Theory ◽  
Edge Vortex

We provide a scaling law for the lift force of autorotating falling seeds at terminal velocity to describe the relation among the lift force, seed geometry and terminal descending and rotating velocities. Two theories, steady wing-vortex theory and actuator-disk theory, are examined to derive the scaling law. In the steady wing-vortex theory, the strength of a leading-edge vortex is scaled with the circulation around a wing and the lift force is modelled by the time derivative of vortical impulse, whereas the conservations of mass, linear and angular momentum, and kinetic energy across the autorotating falling seed are applied in the actuator-disk theory. To examine the validity of the theoretical results, an unsteady three-dimensional numerical simulation is conducted for flow around an autorotating seed (Acer palmatum) during free fall. The sectional lift coefficient predicted from the steady wing-vortex theory reasonably agrees with that from the numerical simulation, whereas the actuator-disk theory fails to provide an estimation of the sectional lift coefficient. The weights of 11 different species of autorotating falling seeds fall on the scaling law derived from the steady wing-vortex theory, suggesting that even a simple theoretical approach can explain how falling seeds support their weights by autorotation once the circulation from a leading-edge vortex is properly included in the theory.

Shear versus vortex-induced lift force on a rigid sphere at moderate Re

2002 ◽  
Vol 473 ◽  
pp. 379-388 ◽  
Author(s):  
P. BAGCHI ◽  
S. BALACHANDAR
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Shear Flow ◽  
Lift Force ◽  
Lift Coefficient ◽  
Rigid Sphere ◽  
Free Rotation ◽  
Rigid Spheres ◽  
Linear Shear ◽  
Strong Lift

The lift forces on rigid spheres entrained in a vortex and a linear shear flow are computed using a direct numerical simulation. The sphere Reynolds number is in the range 10 to 100. The lift coefficient in a vortex is shown to be nearly two orders of magnitude higher than that in a shear flow. The inviscid mechanism is shown to be inadequate to account for the enhanced lift force. The effect of free rotation of the sphere is also shown to be too small to account for the enhanced lift force. Flow structure around the sphere is studied to explain the generation of the strong lift force in a vortex.

Investigation of the aerodynamic performance and flow physics on cross sections of Dragonfly wing on flapping and pitching motion in low Reynolds number

2017 ◽  
Vol 233 (2) ◽  
pp. 589-603 ◽  
Author(s):  
Roham Lavimi ◽  
Mohammad Hojaji ◽  
Mojtaba Dehghan Manshadi
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
Cross Sections ◽  
Lift Coefficient ◽  
Aerodynamic Performance ◽  
Pitching Motion ◽  
Flapping Motion ◽  
Flow Physics ◽  
Dragonfly Wing ◽  
Low Reynolds

In this research, the flow physics and aerodynamic performance of dragonfly cross sections, used in Micro Aerial Vehicles (MAVs), in low Reynolds are investigated. The main objective of the research is to study the performance of dragonfly wing cross-sections flapping motion in Reynolds 5000 and 10,000. Pitching motion is one of the most important mechanisms in force lifting generation, and the effects of Reynolds number and mean angle of attack on aerodynamic coefficients have been extensively investigated for the pitching motion. In the present study, the geometry of two cross sections of dragonfly was extracted. Incompressible, two-dimensional and unsteady Navier–Stokes equations have been used to simulate the flow. k − ɛ RNG model was used for turbulence modeling. To simulate the wing pitching motion, the dynamic mesh method was used. The results showed that in flapping motion, pitching-up rotation has caused a rapid increase in lift coefficient. Furthermore, it was found that the absence of stall does not increase the lift and drag coefficients, while formation of new strong vorticity layers have caused an increase in lift coefficient. On the other hand, corrugations on the cross sections of the dragonfly in the pitching motion cause the delay of separation and increasing the lift coefficient. In flapping motion and the pitching motion, the lift coefficients of three cross sections were increased due to stronger vorticity layers by reducing the Reynolds number. Due to the existence of corrugations, the first and the second cross sections have good aerodynamic performance, compared to the flat plate. The comparison carried out in the current research showed that the second cross section is a proper replacement for the flat plate in MAVs.

Dynamic stall of an airfoil with different mounting angle of gurney flap

2020 ◽  
Vol 92 (7) ◽  
pp. 1037-1048
Author(s):  
Mehran Masdari ◽  
Milad Mousavi ◽  
Mojtaba Tahani
Keyword(s):  
Lift Coefficient ◽  
Oscillation Amplitude ◽  
Vertical Axis ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Content Type ◽  
Naca0012 Airfoil ◽  
Gurney Flap ◽  
Stall Angle ◽  
Axis Length

Purpose One of the best methods to improve wind turbine aerodynamic performance is modification of the blade’s airfoil. The purpose of this paper is to investigate the effects of gurney flap geometry and its oscillation parameters on the pitching NACA0012 airfoil. Design/methodology/approach This numerical solution has been carried out for different cases of gurney flap mounting angles, heights, reduced frequencies and oscillation amplitudes, then the results were compared to each other. The finite volume method was used for the discretization of the governing equations, and the PISO algorithm was used to solve the equations. Also, the “SST” was adopted as the turbulence model in the simulation. Findings In this paper, the different parameters of gurney flap were investigated. The results showed that the best range of gurney flap height are between 1 and 3.2% of chord and the best ratio of lifting to drag coefficient is achieved in gurney flap with an angle of 90° relative to the chord direction. The dynamic stall angle of the airfoil with gurney flap decreases were compared to without gurney flap. Earlier LEV formation can be one of the main reasons for decreasing the dynamic stall angle of the airfoil with gurney flap. Increasing the reduced frequency and oscillation amplitude causes rising of maximum lift coefficient and consequently lift curve slope. Moreover, gurney flap with mounting angle has a lower hinge moment than the gurney flap without mounting angle but with the same vertical axis length. So, there is more complexity in structural design concerning the gurney flap without mounting angle. Practical implications Improving aerodynamic efficiency of airfoils is vital for obtaining more output power in VAWTs. Gurney flaps are one of the best mechanisms to increase the aerodynamic performance of the airfoil and increases the efficiency of VAWTs. Originality/value Investigating the hinge moment on the connection point of the airfoil, gurney flap and try to compare the gurney flap with and without angle.

scholarly journals Improving the aerodynamic performance of a cycloidal rotor through active compliant morphing

2017 ◽  
Vol 121 (1241) ◽  
pp. 901-915
Author(s):  
L. Ferrier ◽  
M. Vezza ◽  
H. Zare-Behtash
Keyword(s):  
Negative Impact ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Micro Air Vehicles ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Marine Vehicles ◽  
Aerospace Applications ◽  
Naca 0015 ◽  
Air Vehicles

ABSTRACTCycloidal rotors are a novel form of propulsion system that can be adapted to various forms of transport such as air and marine vehicles, with a geometrical design differing significantly from the conventional screw propeller. Research on cycloidal rotor design began in the early 1930s and has developed throughout the years to the point where such devices now operate as propulsion systems for various aerospace applications such as micro air vehicles, unmanned air vehicles and compound helicopters. The majority of research conducted on the cycloidal rotor’s aerodynamic performance have not assessed mitigating the dynamic stall effect, which can have a negative impact on the rotor performance when the blades operate in the rotor retreating side. A solution has been proposed to mitigate the dynamic stall effect through employment of active, compliant leading-edge morphing. A review of the current state of the art in this area is presented. A two-dimensional, implicit unsteady numerical analysis was conducted using the commercial computational fluid dynamics software package STAR CCM+, on a two-bladed cycloidal rotor. An overset mesh technique, otherwise known as a chimera mesh, was used to apply complex transient motions to the simulations. Active, compliant leading-edge morphing is applied to an oscillating NACA 0015 aerofoil to attempt to mitigate the dynamic stall whilst maintaining the positive dynamic lift coefficient (Cl) contributions. It was verified that by applying a pulsed input leading-edge rotational morphing schedule, the leading-edge vortex does not fully form and the large flow separation is prevented. Further work in this investigation will focus on coupling the active, leading-edge motion to the cycloidal rotor model with the aim to maximise aerodynamic performance.

scholarly journals A Study on Aerodynamic Behavior of Subsonic UAVs' Wing Sections with Flaps

2020 ◽  
Vol vm02 (is01) ◽  
pp. 22-27
Author(s):  
Halil Yalcin Akdeniz
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Open Source Software ◽  
Lift Force ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Performance Parameters ◽  
Original Design ◽  
Flap Design

In this study, it is aimed to assess the aerodynamic and flight effects of the flap design on an airfoil. For this purpose, NACA 4415 type wing profile, which can also be used in unmanned aerial vehicles (UAVs), is selected. The original design and the +5-degree flapped design which has constant other design features are compared. Assessments are performed under constant Reynolds numbers and an angle of attack between 0-10 degrees with a 1-degree interval. Analyses are made using the open-source software XFLR5. For the flapped design is named NACA 4415-2, some basic aerodynamic performance parameters such as coefficient of drag (CD), coefficient of lift (CL) coefficient of pressure (Cp) maximum lift coefficient (Clmax) and minimum stall velocity (Vstall) have been observed. According to results, when the flap with 5o is added to the airfoil, it has been observed that the CL and Lift force of the original design of the airfoil increase significantly, CD of the airfoil increase partially, and the pressure coefficient tends to decrease significantly. Furthermore, it has been observed that while the minimum stall velocity has decreased, Clmax values increased.

scholarly journals NUMERICAL SIMULATION ON REAR SPOILER ANGLE OF MINI MPV CAR FOR CONDUCTING STABILITY AND SAFETY

SINERGI ◽  
2019 ◽  
Vol 24 (1) ◽  
pp. 23
Author(s):  
Alief Avicenna Luthfie ◽  
Dedik Romahadi ◽  
Hanif Ghufron ◽  
Solli Dwi Murtyas
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Drag Force ◽  
Lift Force ◽  
Lift Coefficient ◽  
Air Resistance ◽  
Rear Part ◽  
Rear Spoiler ◽  
Computational Fluid Dynamics Cfd ◽  
Drag And Lift

Spoiler attached on the rear part of a car can generate drag force and negative lift force, called downforce. This drag force can increase air resistance to the car, meanwhile, a negative lift force can improve the car’s stability and safety. Refer to many researchers, the shape and the angle of the spoiler give different aerodynamic effects and therefore give a different value of drag force and lift force. Based on these facts, this study was focused on the analysis of different spoiler angle attached to a mini MPV car to drag and lift force generated by the spoiler. The method used in this study is a numerical simulation using the Computational Fluid Dynamics (CFD) technique. The analysis was carried out at different spoiler angle and car’s speed. The spoiler angles are -20o, -10o, 0o, 10o, and 20o. The car’s speeds are 40 km/h, 60 km/h, 80 km/h, 100 km/h, and 120 km/h. Then the drag and lift force and their coefficient generated by different spoiler angles were being investigated at specified speeds. The result shows that higher spoiler angles generate higher drag and lower lift. Spoiler angles higher than 0o generate negative lift force, otherwise generate positive lift force. Therefore, to increase a car’s stability and safety, it is recommended to use a spoiler angle higher than 0o. Based on the result, it is best to use spoiler angle 10o because it generates negative lift force with -0.05 lift coefficient and 0,68 drag coefficient.

Sign in / Sign up

Export Citation Format

Share Document