scholarly journals Influence of Milled Glass Fiber Fillers on Mode I & Mode II Interlaminar Fracture Toughness of Epoxy Resin for Fabrication of Glass/Epoxy Composites

Fibers ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 36
Author(s):  
Kannivel Saravanakumar ◽  
Vellayaraj Arumugam ◽  
Rotte Souhith ◽  
Carlo Santulli
Keyword(s):  
Fracture Toughness ◽  
Glass Fiber ◽  
Composite Laminates ◽  
Glass Fibers ◽  
Mode I ◽  
Mode Ii ◽  
Additional Energy ◽  
Maximal Increase ◽  
Mode Ii Fracture Toughness ◽  
Delamination Resistance

The present work is focused on improving mode I and mode II delamination resistance of glass/epoxy composite laminates (50 wt.% of glass fibers) with milled glass fibers, added in various amounts (2.5, 5, 7.5 and 10% of the epoxy weight). Including fillers in the interlayer enhances the delamination resistance by providing a bridging effect, therefore demanding additional energy to initiate the crack in the interlaminar domain, which results in turn in enhanced fracture toughness. The maximal increase of mode I and mode II fracture toughness and of flexural strength was obtained by the addition of 5% milled glass fiber. The mechanism observed suggests that crack propagation is stabilized even leading to its arrest/deflection, as a considerable amount of milled glass fiber filler was oriented transverse to the crack path. In contrast, at higher filler loading, tendency towards stress concentration grows due to local agglomeration and improper dispersion of excess fillers in inter/intralaminar resin channel, causing poor adhesion to the matrix, which leads to reduction in fracture toughness, strength and strain to failure. Fractured surfaces analyzed using scanning electron microscopy (SEM) revealed a number of mechanisms, such as crack deflection, individual debonding and filler/matrix interlocking, all contributing in various ways to improve fracture toughness.

Seawater effects on interlaminar fracture toughness of glass fiber/epoxy laminates modified with multiwall carbon nanotubes

2020 ◽  
pp. 002199832095078
Author(s):  
Julio A Rodríguez-González ◽  
Carlos Rubio-González
Keyword(s):  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Glass Fiber ◽  
Composite Laminates ◽  
Multiwall Carbon Nanotubes ◽  
Mode I ◽  
Mode Ii ◽  
Interlaminar Fracture Toughness ◽  
Multiscale Composite ◽  
Multiwall Carbon

In this work, the effect of seawater ageing on mode I and mode II interlaminar fracture toughness ([Formula: see text] and [Formula: see text]) of prepreg-based woven glass fiber/epoxy laminates with and without multiwall carbon nanotubes (MWCNTs) has been investigated. The first part of the investigation reports the moisture absorption behavior of multiscale composite laminates exposed to seawater ageing for ∼3912 h at 70 °C. Then, the results of mode I and mode II fracture tests are presented and a comparison of [Formula: see text] and [Formula: see text] for each type of material group and condition is made. Experimental results showed the significant effect of seawater ageing on [Formula: see text] of multiscale composite laminates due to matrix plasticization and fiber bridging. The improvement in [Formula: see text] of the wet glass fiber/epoxy laminate was about 50% higher than that of the neat laminate (without MWCNTs) under dry condition. It was also found that the presence of MWCNTs into composite laminates promotes a moderate increase (8%) in their [Formula: see text] as a result of the additional toughening mechanisms induced by CNTs during the delamination process. Scanning electron microscopy analysis conducted on fracture surface of specimens reveals the transition from brittle (smooth surface) to ductile (rough surface) in the morphology of composite laminates due to the influence of seawater ageing on the polymeric matrix and fiber/matrix interface.

Comparison of mode I and mode II fracture toughness of an 8090 AlLi alloy

1991 ◽  
Vol 149 (1) ◽  
pp. L1-L3 ◽  
Author(s):  
S.V. Kamat ◽  
N. Eswara Prasad ◽  
G. Malakondaiah
Keyword(s):  
Fracture Toughness ◽  
Mode I ◽  
Mode Ii ◽  
Mode Ii Fracture ◽  
Mode Ii Fracture Toughness

scholarly journals Woven Glass Fiber Composites with Aligned Carbon Nanotube Sheet Interlayers

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Hardik Bhanushali ◽  
Philip D. Bradford
Keyword(s):  
Fracture Toughness ◽  
Glass Fiber ◽  
Mode I ◽  
Mode Ii ◽  
Interlaminar Fracture Toughness ◽  
Fiber Reinforced ◽  
Interlaminar Fracture ◽  
Glass Fiber Reinforced ◽  
Short Beam ◽  
Woven Glass Fiber

This investigation describes the design, fabrication, and testing of woven glass fiber reinforced epoxy matrix laminates with aligned CNT sheets integrated between plies in order to improve the matrix dominated through thickness properties such as the interlaminar fracture toughness at ply interfaces. Using aligned CNT sheets allows for a concentration of millimeter long CNTs at the most likely point of laminate failure. Mode I and Mode II interlaminar fracture toughness of various CNT modified samples were investigated using double cantilever beam (DCB) and end notched flexure (ENF) experiments, respectively. Short beam strength (SBS) and in-plane tensile properties of the CNT modified samples were also investigated. Moderate improvement was observed in Mode I and Mode II fracture toughness at crack initiation when aligned CNT sheets with a basis weight of 0.354 g/m2were used to modify the ply interface. No compromise in the in-plane mechanical properties of the laminate was observed and very little improvement was observed in the shear related short beam strength of the CNT modified laminates as compared to the control samples. Integration of aligned CNT sheets into the composite laminate imparted in-plane and through thickness electrical properties into the nonconductive glass fiber reinforced epoxy composite laminates.

Interlaminar Fracture Toughness of Composite Laminate with Splicing Plies

2011 ◽  
Vol 194-196 ◽  
pp. 1697-1702
Author(s):  
Li Liang ◽  
Pu Rong Jia ◽  
Gui Qiong Jiao
Keyword(s):  
Fracture Toughness ◽  
Composite Laminates ◽  
Tensile Testing ◽  
Mode Ii ◽  
Interlaminar Fracture Toughness ◽  
Fiber Reinforced ◽  
Interlaminar Fracture ◽  
Mode Ii Fracture ◽  
Mode Ii Fracture Toughness ◽  
Delamination Failure

Delamination is one of the important damage modes in the fiber-reinforced composite laminates. The interlaminar fracture toughness is the key parameter in delamination failure analysis of composites. The stress analysis by a finite element modeling has shown that the shear stress is very large near the ply splicing area. So the delamination failure is mainly dependent on the mode II fracture toughness. A new way of loading in tensile testing is proposed for the measurement of mode II fracture toughness. Specific specimen with splicing plies has been designed and used for the experiment. Testing study on the carbon-fiber-reinforced laminate with ply splicing was performed. Steady crack propagation has been seen by the tensile testing of the specimen. Mode II fracture toughness GIIC of the laminate has been determined by the experiment data analysis. The experiment and numerical analysis shows that the tensile testing for the measurement of mode II interlaminar fracture toughness is feasible.

Sign in / Sign up

Export Citation Format

Share Document