scholarly journals Augmentation of Heat Transfer in a Circular Channel with Inline and Staggered Baffles

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8593
Author(s):  
Muneerah Al Nuwairan ◽  
Basma Souayeh
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Working Fluid ◽  
Solar Air Heater ◽  
Circular Channel ◽  
Maximum Enhancement ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Sst Model ◽  
Inlet Length

This numerical investigation presents the effects of the position of baffles in the shape of a circle’s segment placed inside a circular channel to improve the thermal and flow performance of a solar air heater. Three different baffles’ positions with Reynolds number varying between 10,000 to 50,000 were investigated computationally. The k-omega SST model was used for solving the governing equations. Air was taken as the working fluid. Three pitch ratios (Y = 3, 4, and 5) were considered, while the height of the baffles remained fixed. The result showed an enhancement in Nusselt number, friction factor, j-factor, and thermal performance factor. Staggered exit-length baffles showed maximum enhancement in heat transfer and pressure drop, while inline inlet-length baffles showed the least enhancement. For a pitch ratio of Y = 3.0, the enhancement in all parameters was the highest, while for Y = 5.0, the enhancement in all parameters was the least. The highest thermal performance factor of 1.6 was found for SEL at Y = 3.0.

scholarly journals Simulation approach on turbulent thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Ing Jiat Kendrick Wong ◽  
Ngieng Tze Angnes Tiong
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Hybrid Nanofluid ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
The Heat Transfer Coefficient

AbstractThis paper presents the numerical study of thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts (square and rectangular). Turbulent regime is studied with the Reynolds number ranges from 10000 to 100000. The heat transfer performance and flow behaviour of hybrid nanofluid are investigated, considering the nanofluid volume concentration between 0.1 and 2%. The thermal performance factor of hybrid nanofluid is evaluated in terms of performance evaluation criteria (PEC). This present numerical results are successfully validated with the data from the literature. The results indicate that the heat transfer coefficient and Nusselt number of Al2O3-Cu/water hybrid nanofluid are higher than those of Al2O3/water nanofluid and pure water. However, this heat transfer enhancement is achieved at the expense of an increased pressure drop. The heat transfer coefficient of 2% hybrid nanofluid is approximately 58.6% larger than the value of pure water at the Reynolds number of 10000. For the same concentration and Reynolds number, the pressure drop of hybrid nanofluid is 4.79 times higher than the pressure drop of water. The heat transfer performance is the best in the circular pipe compared to the non-circular ducts, but its pressure drop increment is also the largest. The hybrid nanofluid helps to improve the problem of low heat transfer characteristic in the non-circular ducts. In overall, the hybrid nanofluid flow in circular and non-circular ducts are reported to possess better thermal performance factor than that of water. The maximum attainable PEC is obtained by 2% hybrid nanofluid in the square duct at the Reynolds Number of 60000. This study can help to determine which geometry is efficient for the heat transfer application of hybrid nanofluid.

Simulation of Circular Tubes Fitted with V Cut and Square Cut Rotors

2013 ◽  
Vol 561 ◽  
pp. 547-552
Author(s):  
Peng Jiang ◽  
Hua Yan ◽  
Zhen Zhang ◽  
Yu Mei Ding ◽  
Wei Min Yang
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Turbulent Heat Transfer ◽  
Cfd Modeling ◽  
Turbulent Heat ◽  
Circular Tubes ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Computational Fluid Dynamics Cfd ◽  
Good Agreement

This work presents the effect of V cut and square cut rotors in circular tubes for turbulent heat transfer using computational fluid dynamics (CFD) modeling. The computational results are in good agreement with experimental data. The obtained results reveal that the use of square cut rotors leads to higher Nusselt number than use of V cut rotors. The results also show that the heat transfer rate, friction factor and thermal performance factor of rotors with square cut increase with the increase of width (a) and depth (b) of rotors’ cut. Square cut rotors with a=b=3 yields higher mean thermal performance factor than those with other width and depth, a=b=1, 2 and the highest thermal performance factor of square cut rotors at a=b=1, 2, 3 are found to be 2.08, 2.11 and 2.13.

Experimental and Numerical Investigation of Flow and Heat Transfer in Stationary Two-Pass Rectangular Duct (AR = 1:2) with Continuous and Broken V- shaped ribs

2021 ◽  
pp. 1-37
Author(s):  
Ramesh Erelli ◽  
Arun Saha
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Heated Surface ◽  
Reynolds Analogy ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Friction Factors ◽  
Local Temperature Distribution

Abstract The combined experimental and Large Eddy Simulations (LES) were performed in the stationary two-pass duct of aspect ratio (AR) 1:2. The experiments were conducted with three different rib arrangements, namely 60° V, 60° V-IV, and broken 60° V-IV ribs, and analysis was carried out with Reynolds numbers of 45,000, 60,000, and 75,000. The infrared thermography (IRT) technique is employed to obtain the local temperature distribution on heated smooth and ribbed surfaces. In all ribbed cases, the copper ribs are glued to the heated surface with a fixed rib height-to-hydraulic diameter (e / Dh) ratio is 0.125 and the rib pitch-to-height ratio (P / e) is 10 and 5 for continuous and broken ribs, respectively. In addition, LES turbulence model was adopted for carrying out simulation to understand the flow and heat transfer behavior in ducts populated with all three V-shaped ribs. The comparison of the time-averaged thermal fields generated using computations has been made with experimentally measured Nusselt numbers, friction factors, thermal performance factor (TPF), and Reynolds analogy performance parameter (RAPP) for all cases. The overall thermal performance factor was found to be quantitatively within 8.0 - 10.66% between experimental and numerical results. Among all the cases, the 60° V-IV ribbed duct provides the best TPF and RAPP than the other two ribbed ducts, whereas the smooth duct shows poor TPF.

scholarly journals Numerical investigation of the performance of perforated baffles in a plate-fin heat exchanger

2020 ◽  
pp. 90-90 ◽  
Author(s):  
Houari Ameur ◽  
Djamel Sahel ◽  
Younes Menni
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Numerical Investigation ◽  
Thermal Performance ◽  
Viscous Fluids ◽  
Performance Factors ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Smooth Channel ◽  
Inelastic Shear

The present paper is a numerical investigation on the performance of perforated baffles in a plate-fin heat exchanger. Two types of perforations are studied, namely the circular and elliptical shapes. Values of heat transfer coefficient, pressure drop and thermal performance factor are determined for both cases and compared with those for a smooth channel. Also, the flow fields and heat transfer characteristics are determined for different fluids and various Reynolds numbers. The working fluids are complex, non-Newtonian and have an inelastic shear thinning behavior. The obtained results showed a good enhancement in the thermal performance factor by the suggested design in baffles. In the case of low viscous fluids, the elliptical perforated baffle performs better (by about 63.4%) than the circular one for all values of Re. But for highly viscous fluids, the elliptical perforation shows higher thermal performance than the circular hole by about 25% for low Re and 27% for high Re. The overall thermal performance factors are about 1.55 and 1.74 for the circular and elliptical perforations, respectively.

scholarly journals Comparative Studies on Thermal Performance of Conic Cut Twist Tape Inserts with SiO2and TiO2Nanofluids

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
Sami D. Salman ◽  
Abdul Amir H. Kadhum ◽  
Mohd S. Takriff ◽  
Abu Bakar Mohamad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Thermal Performance ◽  
Volume Concentration ◽  
Twisted Tape ◽  
Maximum Heat ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Maximum Heat Transfer ◽  
Twist Ratio

This paper presents a comparison study on thermal performance conic cut twist tape inserts in laminar flow of nanofluids through a constant heat fluxed tube. Three tape configurations, namely, quadrant cut twisted tape (QCT), parabolic half cut twisted tape (PCT), and triangular cut twisted (VCT) of twist ratioy= 2.93 and cut depthde= 0.5 cm were used with 1% and 2% volume concentration of SiO2/water and TiO2/water nanofluids. Typical twist tape with twist ratio ofy= 2.93 was used for comparison. The results show that the heat transfer was enhanced by increasing of Reynolds number and nanoparticles concentration of nanofluid. The results have also revealed that the use of twist tape enhanced the heat transfer coefficient significantly and maximum heat transfer enhancement was achieved by the presence of triangular cut twist tape insert with 2% volume concentration of SiO2nanofluid. Over the range investigated, the maximum thermal performance factor of 5.13 is found with the simultaneous use of the SiO2nanofluid at 2% volume concentration VCT at Reynolds number of 220. Furthermore, new empirical correlations for Nusselt number, friction factor, and thermal performance factor are developed and reported.

scholarly journals Numerical Study of Heat Transfer Enhancement of Internal Flow Using Double-Sided Delta-Winglet Tape Insert

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3170 ◽  
Author(s):  
Agung Wijayanta ◽  
Muhammad Aziz ◽  
Keishi Kariya ◽  
Akio Miyara
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Thermal Performance ◽  
Numerical Study ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Enhanced Tube ◽  
Delta Winglet ◽  
Experimental Values

A numerical study was performed to investigate the thermal performance characteristics of an enhanced tube heat exchanger fitted with punched delta-winglet vortex generators. Computational fluid dynamics modeling was applied using the k–ε renormalized group turbulence model. Benchmarking was performed using the results of the experimental study for a similar geometry. Attack angles of 30°, 50°, and 70° were used to investigate the heat transfer and pressure drop characteristics of the enhanced tube. Flow conditions were considered in the turbulent region in the Reynolds number range of 9100 to 17,400. A smooth tube was employed for evaluating the increment in the Nusselt number and the friction factor characteristics of the enhanced tube. The results show that the Nusselt number, friction factor, and thermal performance factor have a similar tendency. The presence of this insert offers a higher thermal performance factor as compared to that obtained with a plain tube. Vortex development in the flow structure aids in generating a vortex flow, which increases convective heat transfer. In addition, as the angle is varied, it is observed that the largest attack angle provides the highest thermal performance factor. The greatest increase in the Nusselt number and friction factor, respectively, was found to be approximately 3.7 and 10 times greater than those of a smooth tube. Through numerical simulations with the present simulation condition, it is revealed that the thermal performance factor approaches the value of 1.1. Moreover, the numerical and experimental values agree well although they tend to be different at high Reynolds number conditions. The numerical and experimental values both show similar trends in the Nusselt number, friction factor, and thermal performance factor.

Sign in / Sign up

Export Citation Format

Share Document