scholarly journals Simulation and Performance Analysis of Air-Type PVT Collector with Interspaced Baffle-PV Cell Design

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5372
Author(s):  
Jong-Gwon Ahn ◽  
Ji-Suk Yu ◽  
Fred Edmond Boafo ◽  
Jin-Hee Kim ◽  
Jun-Tae Kim
Keyword(s):  
Thermal Performance ◽  
Simulation Modeling ◽  
Side Surface ◽  
Climatic Conditions ◽  
Outdoor Environment ◽  
Back Side ◽  
Design Elements ◽  
Outdoor Test ◽  
And Performance ◽  
Good Agreement

A Photovoltaic Thermal (PVT) collector produces heat and electricity simultaneously. Air-type PVT collector uses air as a transfer medium to take heat from PV back side surface. The performance of the air-type PVT collector is affected by design elements such as PV types, inside structures in heat collecting space (baffle or fins), the shape of the air pathway, etc. In this study, an advanced air-type PVT collector was designed with curved baffles (absorber) to improve thermal performance. Within the air-type PVT collector, PV cells were arranged in an interspaced design, and the curved baffles were located in the collecting space to increase heat efficiently. The absorber received solar radiation directly and was utilized as baffles for improving thermal performance. The air-type PVT collector was fabricated and tested in an outdoor environment considering the climatic conditions of Daejeon, Republic of Korea. In addition, based on experiment parameters and data, the annual thermal and electrical performances of the system were analyzed by simulation modeling using the TRNSYS program. Thermal and electrical efficiencies were 37.1% and 6.4% (according to module area) for outdoor test conditions, respectively. Numerical and experimental results were in good agreement with an error of 4% and 0.24% for thermal and electrical efficiencies, respectively. Annual heat gain was 644 kWh th/year, and generated power was 118 kWh el/year.

Thermal Performance Analysis of a Rectangular Longitudinal Finned Solar Air Heater With Semicircular Absorber Plate

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Satyender Singh ◽  
Prashant Dhiman
Keyword(s):  
Thermal Performance ◽  
Numerical Solutions ◽  
Solar Air Heater ◽  
Duct Flow ◽  
Balance Equations ◽  
Absorber Plate ◽  
Ansys Fluent ◽  
Air Heater ◽  
Glass Cover ◽  
Good Agreement

Thermal performance of a single-pass single-glass cover solar air heater consisting of semicircular absorber plate finned with rectangular longitudinal fins is investigated. The analysis is carried out for different hydraulic diameters, which were obtained by varying the diameter of the duct from 0.3–0.5 m. One to five numbers of fins are considered. Reynolds number ranges from 1600–4300. Analytical solutions for energy balance equations of different elements and duct flow of the solar air heater are presented; results are compared with finite-volume methodology based numerical solutions obtained from ansys fluent commercial software, and a fairly good agreement is achieved. Moreover, analysis is extended to check the effect of double-glass cover and the recycle of the exiting air. Results revealed that the use of double-glass cover and recycle operation improves the thermal performance of solar air heater.

Thermal performance comparison of different sun tracking configurations

2019 ◽  
Vol 88 (2) ◽  
pp. 20902
Author(s):  
O. Achkari ◽  
A. El Fadar
Keyword(s):  
Thermal Performance ◽  
Electricity Generation ◽  
Arid Regions ◽  
Performance Comparison ◽  
Water Desalination ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
The Impact ◽  
The Mathematical Model ◽  
Good Agreement

Parabolic trough collector (PTC) is one of the most widespread solar concentration technologies and represents the biggest share of the CSP market; it is currently used in various applications, such as electricity generation, heat production for industrial processes, water desalination in arid regions and industrial cooling. The current paper provides a synopsis of the commonly used sun trackers and investigates the impact of various sun tracking modes on thermal performance of a parabolic trough collector. Two sun-tracking configurations, full automatic and semi-automatic, and a stationary one have numerically been investigated. The simulation results have shown that, under the system conditions (design, operating and weather), the PTC's performance depends strongly on the kind of sun tracking technique and on how this technique is exploited. Furthermore, the current study has proven that there are some optimal semi-automatic configurations that are more efficient than one-axis sun tracking systems. The comparison of the mathematical model used in this paper with the thermal profile of some experimental data available in the literature has shown a good agreement with a remarkably low relative error (2.93%).

scholarly journals Novel Hexagonal Dual-Mode Substrate Integrated Waveguide Filter with Source-Load Coupling

2014 ◽  
Vol 2014 ◽  
pp. 1-5
Author(s):  
Ziqiang Xu ◽  
Gen Zhang ◽  
Hong Xia ◽  
Meijuan Xu
Keyword(s):  
Center Frequency ◽  
Substrate Integrated Waveguide ◽  
Fractional Bandwidth ◽  
Dual Mode ◽  
Transmission Zeros ◽  
Cavity Structure ◽  
Waveguide Filter ◽  
And Performance ◽  
Single Cavity ◽  
Good Agreement

Hexagonal dual-mode cavity and its application to substrate integrated waveguide (SIW) filter are presented. The hexagonal SIW resonator which can combine flexibility of rectangular cavity and performance of circular cavity is convenient for dual-mode bandpass filters design. By introducing coupling between source and load, the filter not only has good selectivity due to two controllable transmission zeros, but also has a small size by the virtue of its single-cavity structure. A demonstration filter with a center frequency of 10 GHz and a 3 dB fractional bandwidth of 4% is designed and fabricated to validate the proposed structure. Measured results are in good agreement with simulated ones.

Predictions of the Effect of Roughness on Heat Transfer From Turbine Airfoils

1998 ◽  
Author(s):  
Anil K. Tolpadi ◽  
Michael E. Crawford
Keyword(s):  
Heat Transfer ◽  
Side Surface ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Surface Finishing ◽  
Transfer Coefficients ◽  
Average Roughness ◽  
Wide Range ◽  
Turbine Airfoils ◽  
Good Agreement

The heat transfer and aerodynamic performance of turbine airfoils are greatly influenced by the gas side surface finish. In order to operate at higher efficiencies and to have reduced cooling requirements, airfoil designs require better surface finishing processes to create smoother surfaces. In this paper, three different cast airfoils were analyzed: the first airfoil was grit blasted and codep coated, the second airfoil was tumbled and aluminide coated, and the third airfoil was polished further. Each of these airfoils had different levels of roughness. The TEXSTAN boundary layer code was used to make predictions of the heat transfer along both the pressure and suction sides of all three airfoils. These predictions have been compared to corresponding heat transfer data reported earlier by Abuaf et al. (1997). The data were obtained over a wide range of Reynolds numbers simulating typical aircraft engine conditions. A three-parameter full-cone based roughness model was implemented in TEXSTAN and used for the predictions. The three parameters were the centerline average roughness, the cone height and the cone-to-cone pitch. The heat transfer coefficient predictions indicated good agreement with the data over most Reynolds numbers and for all airfoils-both pressure and suction sides. The transition location on the pressure side was well predicted for all airfoils; on the suction side, transition was well predicted at the higher Reynolds numbers but was computed to be somewhat early at the lower Reynolds numbers. Also, at lower Reynolds numbers, the heat transfer coefficients were not in very good agreement with the data on the suction side.

Models for New Corrugated and Porous Solar Air Collectors under Transient Operation

2017 ◽  
Vol 42 (1) ◽  
Author(s):  
Qahtan Adnan Abed ◽  
Viorel Badescu ◽  
Adrian Ciocanea ◽  
Iuliana Soriga ◽  
Dorin Bureţea
Keyword(s):  
Climatic Conditions ◽  
Meteorological Conditions ◽  
Bias Error ◽  
First Order ◽  
Solar Air Collector ◽  
Section Surface ◽  
South Eastern Europe ◽  
Main Components ◽  
Theoretical Results ◽  
Good Agreement

AbstractMathematical models have been developed to evaluate the dynamic behavior of two solar air collectors: the first one is equipped with a V-porous absorber and the second one with a U-corrugated absorber. The collectors have the same geometry, cross-section surface area and are built from the same materials, the only difference between them being the absorbers. V-corrugated absorbers have been treated in literature but the V-porous absorbers modeled here have not been very often considered. The models are based on first-order differential equations which describe the heat exchange between the main components of the two types of solar air heaters. Both collectors were exposed to the sun in the same meteorological conditions, at identical tilt angle and they operated at the same air mass flow rate. The tests were carried out in the climatic conditions of Bucharest (Romania, South Eastern Europe). There is good agreement between the theoretical results and experiments. The average bias error was about 7.75 % and 10.55 % for the solar air collector with “V”-porous absorber and with “U”-corrugated absorber, respectively. The collector based on V-porous absorber has higher efficiency than the collector with U-corrugated absorber around the noon of clear days. Around sunrise and sunset, the collector with U-corrugated absorber is more effective.

scholarly journals Thermal Performance of a Concrete Cool Roof under Different Climatic Conditions of Mexico

2014 ◽  
Vol 57 ◽  
pp. 1753-1762 ◽  
Author(s):  
I. Hernández-Pérez ◽  
G. Álvarez ◽  
H. Gilbert ◽  
J. Xamán ◽  
Y. Chávez ◽  
...  
Keyword(s):  
Thermal Performance ◽  
Climatic Conditions ◽  
Cool Roof

scholarly journals Mathematics Modelling and Performance Analysis of the Heat Transfer on Vacuum Tube Collector of Water Heater Application

2020 ◽  
Vol 190 ◽  
pp. 00022
Author(s):  
Lia Hamanda ◽  
Gunawan Nugroho
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Thermal Performance ◽  
Solar Collector ◽  
Dynamic Behaviour ◽  
Tube Axis ◽  
Outdoor Temperature ◽  
Water Heater ◽  
And Performance ◽  
Mathematical Modelling And Simulation

The aim of this work is to study a mathematical modelling and simulation for predicting the thermal performance heat-pipe evacuated a solar collector for water heater, which was considered the temperature distribution along the tube axis and radius. This model used to help in studying the dynamic behaviour of the system design and the effect of influential parameter on the water heater process. The result showed that water heating is affected by the surface of collector, metrological conditions such as solar radiation and outdoor temperature, even the thermal performance of the collector.

scholarly journals Design of steering system of a buggy

2020 ◽  
Vol 327 ◽  
pp. 03004
Author(s):  
D. Santana Sanchez ◽  
A. Mostafa
Keyword(s):  
Carrying Capacity ◽  
Steering System ◽  
Nonlinear Finite Element ◽  
Load Carrying Capacity ◽  
Dynamic Effects ◽  
Flexural Behaviour ◽  
Steering Angle ◽  
Load Carrying ◽  
And Performance ◽  
Good Agreement

The present paper discusses the design analysis and limitations of the steering system of a buggy. Many geometrical and performance characteristics of the designed steering system were considered to address the kinematic constraints and load carrying capacity of the steering elements. Ackremann geometry approach was used to assess the limiting steering angle, while Lewis bending formula with the inclusion of dynamic effects was employed to characterise the flexural properties of the rack and pinion steering system. Analytical results were numerically verified using ABAQUS/Explicit nonlinear finite element (FE) package. Good agreement has been achieved between analytical and numerical results in predicting the flexural behaviour of the steering rack and pinion system.

Sign in / Sign up

Export Citation Format

Share Document