scholarly journals Effect of the HPDI and PPCI Combustion Modes of Direct-Injection Natural Gas Engine on Combustion and Emissions

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1957
Author(s):  
Shouying Jin ◽  
Jinze Li ◽  
Longfei Deng ◽  
Binyang Wu
Keyword(s):  
Natural Gas ◽  
Oil And Gas ◽  
Direct Injection ◽  
Combustion Process ◽  
Mixture Distribution ◽  
Premixed Combustion ◽  
Diffusion Combustion ◽  
Injection Timing ◽  
Combustion Modes ◽  
Ignition Characteristics

Natural gas (NG) engines have very broad application prospects. The pilot-ignited NG diesel engine can be organized into two combustion modes according to the sequence of oil and gas injection: (1) High-pressure direct injection, where NG is mainly diffused combustion; and (2) partially premixed compression ignition, where NG is mainly premixed combustion. In this study, we used CONVERGE to explore the influence of the NG injection timing on the distribution of the mixture equivalence ratio, ignition characteristics, thermal efficiency, emission, and combustion reaction rate under the two combustion modes. We also used a multi-step soot model to analyze the particle mass and quantity. We showed herein that the NG injection timing significantly affects the mixture distribution in the cylinder, thereby consequently affecting the combustion process. Both very early and very late injection times were not conducive to NG combustion. In addition, the mass, quantity, and diameter of the soot produced by diffusion combustion were larger than those produced with premixed combustion.

Experimental and Theoretical Optimization of Combustion Chamber and Fuel Distribution for the Low Emission Direct-Injection Diesel Engine

2002 ◽  
Vol 125 (1) ◽  
pp. 351-357 ◽  
Author(s):  
Y. Kidoguchi ◽  
M. Sanda ◽  
K. Miwa
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Combustion Process ◽  
Mixture Distribution ◽  
Initial Mixture ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Particulate Emission ◽  
Direct Injection Diesel Engine

Effects of combustion chamber geometry and initial mixture distribution on the combustion process were investigated in a direct-injection diesel engine. In the engine experiment, a high squish combustion chamber with a squish lip could reduce both NOx and particulate emissions with retarded injection timing. According to the results of CFD computation and phenomenological modeling, the high squish combustion chamber with a central pip is effective to keep the combusting mixture under the squish lip until the end of combustion and the combustion region forms rich and highly turbulent atmosphere. This kind of mixture distribution tends to reduce initial burning, resulting in restraint of NOx emission while keeping low particulate emission.

A multistage combustion model and soot formation model for direct-injection diesel engines

2002 ◽  
Vol 216 (6) ◽  
pp. 495-504 ◽  
Author(s):  
G J Micklow ◽  
W Gong
Keyword(s):  
Diesel Engines ◽  
Soot Formation ◽  
Direct Injection ◽  
Combustion Process ◽  
Oxidation Mechanism ◽  
Soot Oxidation ◽  
Premixed Combustion ◽  
Combustion Model ◽  
Diffusion Combustion ◽  
Soot Model

A multistage combustion model for diesel engines is presented in this paper. Three combustion stages, ignition of diesel, premixed combustion and diffusion combustion, are considered in the combustion process in a typical medium speed direct injection diesel engine. The transition from the ignition delay to the premixed combustion stage occurs when the highest temperature in the cylinder is beyond a critical value, and the transition from the premixed combustion model to the diffusion combustion model occurs when a calculated fraction of the premixed fuel is burned, which is determined from an empirical correlation based on the engine design and running conditions. Significant improvements in the predictions for in-cylinder pressure and heat release rate were achieved compared with previous models. A soot model based on the Hiroyasu soot formation mechanism and the Nagle and Strickland-Constable soot oxidation mechanism was implemented in a standard KIVA3V code. The effect of the OH radical in soot oxidation was also incorporated into the soot model. Computations show that OH plays an important role during the late combustion stage. Predicted soot and NOx were compared with measured values and a good agreement was achieved.

scholarly journals A Numerical Study on the Combustion Process and Emission Characteristics of a Natural Gas-Diesel Dual-Fuel Marine Engine at Full Load

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1342
Author(s):  
Van Chien Pham ◽  
Jae-Hyuk Choi ◽  
Beom-Seok Rho ◽  
Jun-Soo Kim ◽  
Kyunam Park ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Simulation Software ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Marine Engine ◽  
Full Load ◽  
Simulation Results

This paper presents research on the combustion and emission characteristics of a four-stroke Natural gas–Diesel dual-fuel marine engine at full load. The AVL FIRE R2018a (AVL List GmbH, Graz, Austria) simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both diesel and dual-fuel mode to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed a good agreement with the measured values reported in the engine’s shop test technical data. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 1.7% and 6.75%, while NO, soot, CO, and CO2 emissions were reduced up to 96%, 96%, 86%, and 15.9%, respectively, in the dual-fuel mode in comparison with the diesel mode. The results also show better and more uniform combustion at the late stage of the combustions inside the cylinder when operating the engine in the dual-fuel mode. Analyzing the emission characteristics and the engine performance when the injection timing varies shows that, operating the engine in the dual-fuel mode with an injection timing of 12 crank angle degrees before the top dead center is the best solution to reduce emissions while keeping the optimal engine power.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

CFD Modelling of the Effects of Injection Timing on the Combustion Process and Emissions in an HSDI Diesel Engine

2012 ◽  
Author(s):  
Raouf Mobasheri ◽  
Zhijun Peng
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Cfd Simulation ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Cfd Modelling ◽  
Combustion Modeling ◽  
Pressure Trace ◽  
Hsdi Diesel Engine

High-Speed Direct Injection (HSDI) diesel engines are increasingly used in automotive applications due to superior fuel economy. An advanced CFD simulation has been carried out to analyze the effect of injection timing on combustion process and emission characteristics in a four valves 2.0L Ford diesel engine. The calculation was performed from intake valve closing (IVC) to exhaust valve opening (EVO) at constant speed of 1600 rpm. Since the work was concentrated on the spray injection, mixture formation and combustion process, only a 60° sector mesh was employed for the calculations. For combustion modeling, an improved version of the Coherent Flame Model (ECFM-3Z) has been applied accompanied with advanced models for emission modeling. The results of simulation were compared against experimental data. Good agreement of calculated and measured in-cylinder pressure trace and pollutant formation trends were observed for all investigated operating points. In addition, the results showed that the current CFD model can be applied as a beneficial tool for analyzing the parameters of the diesel combustion under HSDI operating condition.

scholarly journals Study on the Effect of Second Injection Timing on the Engine Performances of a Gasoline/Hydrogen SI Engine with Split Hydrogen Direct Injecting

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5223
Author(s):  
Guanting Li ◽  
Xiumin Yu ◽  
Ping Sun ◽  
Decheng Li
Keyword(s):  
Numerical Study ◽  
Direct Injection ◽  
Mixture Distribution ◽  
Spark Ignition ◽  
Injection Timing ◽  
Si Engine ◽  
Excess Air ◽  
Crank Angle ◽  
Hc Emissions ◽  
Main Factor

Split hydrogen direct injection (SHDI) has been proved capable of better efficiency and fewer emissions. Therefore, to investigate SHDI deeply, a numerical study on the effect of second injection timing was presented at a gasoline/hydrogen spark ignition (SI) engine with SHDI. With an excess air ratio of 1.5, five different second injection timings achieved five kinds of hydrogen mixture distribution (HMD), which was the main factor affecting the engine performances. With SHDI, since the HMD is manageable, the engine can achieve better efficiency and fewer emissions. When the second injection timing was 105° crank angle (CA) before top dead center (BTDC), the Pmax was the highest and the position of the Pmax was the earliest. Compared with the single hydrogen direct injection (HDI), the NOX, CO and HC emissions with SHDI were reduced by 20%, 40% and 72% respectively.

Sign in / Sign up

Export Citation Format

Share Document