scholarly journals Decomposition Characteristics of SF6 under Arc Discharge and the Effects of Trace H2O, O2, and PTFE Vapour on Its By-Products

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 414
Author(s):  
Ren Yang ◽  
Mengyuan Xu ◽  
Jing Yan ◽  
Minghao Yang ◽  
Yingsan Geng ◽  
...  
Keyword(s):  
Arc Discharge ◽  
Circuit Breaker ◽  
Arc Plasma ◽  
Gas Chromatograph ◽  
Minimization Method ◽  
Sf6 Circuit Breaker ◽  
Gibbs Free Energy Minimization ◽  
Simulation Results ◽  
By Products ◽  
Good Agreement

The research on decomposition characteristics of SF6 and its by-products have great significance to the operation, maintenance, condition assessment and fault diagnosis of power equipment. In this paper, the particle composition models of SF6, SF6/polytetrafluoroethylene (PTFE), SF6/PTFE/O2, SF6/PTFE/H2O, and SF6/PTFE/O2/H2O were established by using Gibbs free energy minimization method, and the effects of trace H2O and O2 impurities and PTFE vapour on SF6 by-products were studied by the models. In order to verify the correctness of the simulation results, a series of breaking experiments were carried out on a 40.5 kV SF6 circuit breaker, and a gas chromatograph was used to detect and analyse the SF6 by-products. It was found that when PTFE vapour is involved in the arc plasma, the main by-product after arc quenching is CF4, and the molar fractions of C2F6 and C3F8 are very low. When O2 is involved, the main by-products are SOF2, SO2 and SO2F2, and a small amount of CO and CO2 was also produced. When H2O is involved, the main by-products in simulation are SOF2, SO2 and HF, and a small amount of SO2, CO2, CO, SO2F2 and H2 was also produced. The experimental results are in good agreement with the above results.

scholarly journals Measuring Hydrometeors Using a Precipitation Microphysical Characteristics Sensor: Sampling Effect of Different Bin Sizes on Drop Size Distribution Parameters

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Xichuan Liu ◽  
Taichang Gao ◽  
Yuntao Hu ◽  
Xiaojian Shu
Keyword(s):  
Drop Size ◽  
Rain Rate ◽  
Monte Carlo Model ◽  
Rain Gauge ◽  
Sampling Schemes ◽  
Distribution Parameters ◽  
Optimum Sampling ◽  
Simulation Results ◽  
The Impact ◽  
Good Agreement

In order to improve the measurement of precipitation microphysical characteristics sensor (PMCS), the sampling process of raindrops by PMCS based on a particle-by-particle Monte-Carlo model was simulated to discuss the effect of different bin sizes on DSD measurement, and the optimum sampling bin sizes for PMCS were proposed based on the simulation results. The simulation results of five sampling schemes of bin sizes in four rain-rate categories show that the raw capture DSD has a significant fluctuation variation influenced by the capture probability, whereas the appropriate sampling bin size and width can reduce the impact of variation of raindrop number on DSD shape. A field measurement of a PMCS, an OTT PARSIVEL disdrometer, and a tipping bucket rain Gauge shows that the rain-rate and rainfall accumulations have good consistencies between PMCS, OTT, and Gauge; the DSD obtained by PMCS and OTT has a good agreement; the probability of N0, μ, and Λ shows that there is a good agreement between the Gamma parameters of PMCS and OTT; the fitted μ-Λ and Z-R relationship measured by PMCS is close to that measured by OTT, which validates the performance of PMCS on rain-rate, rainfall accumulation, and DSD related parameters.

scholarly journals Validation of MATLAB algorithm to implement a two-step parallel pyrolysis model for the prediction of maximum %char yield

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Ibiba Taiwo Horsfall ◽  
Macmanus Chinenye Ndukwu ◽  
Fidelis Ibiang Abam ◽  
Ololade Moses Olatunji ◽  
Ojong Elias Ojong ◽  
...  
Keyword(s):  
Experimental Data ◽  
Isothermal Condition ◽  
Char Yield ◽  
Experimental Investigations ◽  
Time Saving ◽  
Pyrolysis Products ◽  
Pyrolysis Model ◽  
Experimental Yield ◽  
By Products ◽  
Good Agreement

AbstractNumerical modeling of biomass pyrolysis is becoming a cost and time-saving alternative for experimental investigations, also to predict the yield of the by-products of the entire process. In the present study, a two-step parallel kinetic model was used to predict char yield under isothermal condition. MATLAB ODE45 function codes were employed to solve a set of differential equations that predicts the %char at varying residence times and temperatures. The code shows how the various kinetic parameters and mass of pyrolysis products were determined. Nevertheless, the algorithm used for the prediction was validated with experimental data and results from past works. At 673.15 K, the numerical simulation using ODE45 function gives a char yield of 27.84%. From 573.15 K to 673.15 K, char yield ranges from 31.7 to 33.72% to 27.84% while experimental yield decreases from 44 to 22%. Hence, the error between algorithm prediction and experimental data from literature is − 0.26 and 0.22. Again, comparing the result of the present work with the analytical method from the literature showed a good agreement.

scholarly journals Simulation and Experimental Study on Wear of U-Shaped Rings of Power Connection Fittings under Strong Wind Environment

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 735
Author(s):  
Songchen Wang ◽  
Xianchen Yang ◽  
Xinmei Li ◽  
Cheng Chai ◽  
Gen Wang ◽  
...  
Keyword(s):  
Abrasive Wear ◽  
Adhesive Wear ◽  
Surface Hardness ◽  
Wear Depth ◽  
Strong Wind ◽  
Wear Model ◽  
Wind Environment ◽  
Simulation Results ◽  
Oxidation Wear ◽  
Good Agreement

The objective of this study was to investigate the wear characteristics of the U-shaped rings of power connection fittings, and to construct a wear failure prediction model of U-shaped rings in strong wind environments. First, the wear evolution and failure mechanism of U-shaped rings with different wear loads were studied by using a swinging wear tester. Then, based on the Archard wear model, the U-shaped ring wear was dynamically simulated in ABAQUS, via the Umeshmotion subroutine. The results indicated that the wear load has an important effect on the wear of the U-shaped ring. As the wear load increases, the surface hardness decreases, while plastic deformation layers increase. Furthermore, the wear mechanism transforms from adhesive wear, slight abrasive wear, and slight oxidation wear, to serious adhesive wear, abrasive wear, and oxidation wear with the increase of wear load. As plastic flow progresses, the dislocation density in ferrite increases, leading to dislocation plugs and cementite fractures. The simulation results of wear depth were in good agreement with the test value of, with an error of 1.56%.

TCAD Study of the Raised SiGe Source/Drain in 40nm PMOS

2015 ◽  
Vol 645-646 ◽  
pp. 70-74 ◽  
Author(s):  
Min Zhong ◽  
Yu Hang Zhao ◽  
Shou Mian Chen ◽  
Ming Li ◽  
Shao Hai Zeng ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Critical Role ◽  
Sige Layer ◽  
Strain Engineering ◽  
Effect Transistor ◽  
Simulation Results ◽  
Aided Design ◽  
The Relationship ◽  
Growth Experiments ◽  
Good Agreement

An embedded SiGe layer was applied in the source/drain areas (S/D) of a field-effect transistor to boost the performance in the p channels. Raised SiGe S/D plays a critical role in strain engineering. In this study, the relationship between the SiGe overfilling and the enhancement of channel stress was investigated. Systematic technology computer aided design (TCAD) simulations of the SiGe overfill height in a 40 nm PMOS were performed. The simulation results indicate that a moderate SiGe overfilling induces the highest stress in the channel. Corresponding epitaxial growth experiments were done and the obtained experimental data was in good agreement with the simulation results. The effect of the SiGe overfilling is briefly discussed. The results and conclusions presented within this paper might serve as useful references for the optimization of the embedded SiGe stressor for 40 nm logic technology node and beyond.

Numerical Simulation on Thixo-Forging of Magnesium Matrix Composite

2011 ◽  
Vol 189-193 ◽  
pp. 2535-2538 ◽  
Author(s):  
Hong Yan ◽  
Wen Xian Huang
Keyword(s):  
Numerical Simulation ◽  
Matrix Composite ◽  
Metal Flow ◽  
Magnesium Matrix Composite ◽  
Magnesium Matrix ◽  
Simulation Based ◽  
Prior Literature ◽  
Simulation Results ◽  
Computer Numerical Simulation ◽  
Good Agreement

The thixo-forging of magnesium matrix composite was analyzed with computer numerical simulation based on rigid viscoplastic finite element method. The constitutive model of SiCp/AZ61 composite was established in our prior literature. Behavior of metal flow and temperature field were obtained. The differences between traditional forging and thixo-forging processes were analyzed. Results indicated that thixo-forging was better in filling cavity than forging. Simulation results were good agreement with experimental ones.

Sign in / Sign up

Export Citation Format

Share Document