scholarly journals The Power and Efficiency Analyses of the Cylindrical Cavity Receiver on the Solar Stirling Engine

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5798
Author(s):  
Ji-Qiang Li ◽  
Jeong-Tae Kwon ◽  
Seon-Jun Jang
Keyword(s):  
Heat Exchange ◽  
Inclination Angle ◽  
Wall Temperature ◽  
Area Ratio ◽  
Stirling Engine ◽  
Open Area ◽  
Engine Efficiency ◽  
Aperture Ratio ◽  
Inclination Angles ◽  
Engine Power

The technique of solar dish and Stirling engine combination is the most challenging and promising one. For the efficient conversion of the externally concentrated heat to the usable power, we studied the influences of the wall temperature, inclination angle, and open area ratio of the receiver on the Stirling engine power and efficiency. The theoretical analysis of the heat exchange element of the solar Stirling engine was performed, and the simulation model of the cavity absorber was built and analyzed. The temperature cloud and heat loss trends of the receiver under different wall temperatures, inclination angles, and opening ratios were illustrated. When the wall temperature of the absorber changes from 700 to 1000 K, the efficiency of the engine has increased by 8.8% from 21.34% to 30.11%. The higher the temperature, the higher the efficiency. As the inclination angle of the absorber increases from 0° to 60°, the efficiency of the engine is increased by 7.7% from 21.1% to 28.8%. With the increases of the aperture ratio, the engine output and efficiency reduced. The engine efficiency at the aperture ratio of 0.5 is 4% larger than that at the aperture ratio of 1.

The Experimental Study of Single Droplet Impinging on an Inclined Heated Wall

2020 ◽  
Author(s):  
Wenlong Tian ◽  
Huang Zhang ◽  
Qianfeng Liu ◽  
Guang Hu ◽  
Wen He
Keyword(s):  
Inclination Angle ◽  
Wall Temperature ◽  
Weber Number ◽  
High Speed ◽  
Conservation Equation ◽  
Heated Wall ◽  
Single Droplet ◽  
Droplet Spreading ◽  
Energy Conservation Equation ◽  
Inclination Angles

Abstract We investigated a single droplet impinging on an inclined heated wall with different inclination angles. A high-speed camera was used to observe this impinging process at 10000 frames / second. The phenomena of the droplet spreading, shrinking, rebounding, boiling, break-up and splashing were observed. The effects of the wall temperature (Tw, 40–262 °C), the Weber number of the droplet (Wed, 0.66–589) and the wall inclination angle (α, 0–45.6°) on the spreading behavior of the droplet after impinging on the wall were analyzed. Energy conservation equation was used to analyze experimental results. The results show that increasing the inclination angle of the wall is beneficial to the forward spreading of the droplet along the wall, but not to the downward spreading. When α > 45.6°, the droplet will break through the flow resistance of the wall and slide down all the time. The increase of the wall temperature and the Weber number of the droplet is beneficial to the backward and forward spreading of the droplet. Increasing α, increasing Tw and decreasing Wed will promote the shrinking of the droplet after spreading. In addition, the experimental phenomenon also shows that the larger the wall inclination and the higher the wall temperature, the easier the droplet will break away from the wall.

The Effectiveness of Film Cooling With Three-Dimensional Slot Geometries

1971 ◽  
Vol 93 (4) ◽  
pp. 425-430 ◽  
Author(s):  
M. N. R. Nina ◽  
J. H. Whitelaw
Keyword(s):  
Gas Turbine ◽  
Wall Temperature ◽  
Film Cooling ◽  
Mass Velocity ◽  
Three Dimensional ◽  
Area Ratio ◽  
Hole Injection ◽  
Open Area ◽  
Adiabatic Wall

The paper describes measurements of adiabatic wall temperature downstream of discrete hole injection slots for a range of parameters relevant to gas turbine practice. The influence of open-area-ratio, slot-lip-length and slot-lip-thickness is determined for tangential holes and a range of mass velocity ratios, 0.3 < m < 2.0, and downstream distances up to 40 equivalent slot heights; similar measurements are reported downstream of three-dimensional splash cooling geometries. In all, 13 different three-dimensional configurations are investigated and permit conclusions to be drawn as to the significance of the parameters investigated. The measurements clearly demonstrate the need for a thin and long slot lip and for a large value of open area ratio.

scholarly journals Acoustic Emission Characteristics and Joint Nonlinear Mechanical Response of Rock Masses under Uniaxial Compression

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 200
Author(s):  
Zhongliang Feng ◽  
Xin Chen ◽  
Yu Fu ◽  
Shaoshuai Qing ◽  
Tongguan Xie
Keyword(s):  
Acoustic Emission ◽  
Uniaxial Compression ◽  
Inclination Angle ◽  
Failure Modes ◽  
Strain Curve ◽  
Particle Flow Code ◽  
Rock Masses ◽  
Physical Experiments ◽  
Inclination Angles ◽  
Joint Inclination

The joint arrangement in rock masses is the critical factor controlling the stability of rock structures in underground geotechnical engineering. In this study, the influence of the joint inclination angle on the mechanical behavior of jointed rock masses under uniaxial compression was investigated. Physical model laboratory experiments were conducted on jointed specimens with a single pre-existing flaw inclined at 0°, 30°, 45°, 60°, and 90° and on intact specimens. The acoustic emission (AE) signals were monitored during the loading process, which revealed that there is a correlation between the AE characteristics and the failure modes of the jointed specimens with different inclination angles. In addition, particle flow code (PFC) modeling was carried out to reproduce the phenomena observed in the physical experiments. According to the numerical results, the AE phenomenon was basically the same as that observed in the physical experiments. The response of the pre-existing joint mainly involved three stages: (I) the closing of the joint; (II) the strength mobilization of the joint; and (III) the reopening of the joint. Moreover, the response of the pre-existing joint was closely related to the joint’s inclination. As the joint inclination angle increased, the strength mobilization stage of the joint gradually shifted from the pre-peak stage of the stress–strain curve to the post-peak stage. In addition, the instantaneous drop in the average joint system aperture (aave) in the specimens with medium and high inclination angles corresponded to a rapid increase in the form of the pulse of the AE activity during the strength mobilization stage.

Performance of a Stirling Engine Regenerator Having Finite Mass

1986 ◽  
Vol 108 (4) ◽  
pp. 669-673 ◽  
Author(s):  
J. D. Jones
Keyword(s):  
Finite Element ◽  
Pressure Variation ◽  
Stirling Engine ◽  
System Model ◽  
Finite Mass ◽  
Element System ◽  
The Matrix ◽  
Cyclic Variations ◽  
Good Agreement ◽  
Engine Power

The performance of a Stirling engine regenerator subjected to sinusoidal mass flow rate and pressure variation is analyzed. It is shown that cyclic variations in the temperature of the matrix due to its finite mass lead to an increase in the apparent regenerator effectiveness, but a decrease in engine power. Approximate closed-form expressions for both of these effects are deduced. The results of this analysis are compared with the predictions of a finite-element system model, and good agreement is found.

scholarly journals DETERMINATION OF THE AVERAGE WALL TEMPERATURE OF THE PLATE IN A RECUPERATIVE HEAT EXCHANGER WITH A CORRUGATED MESH INSERT

2021 ◽  
Vol 11 (1) ◽  
pp. 46-55
Author(s):  
Arman B. KOSTUGANOV ◽  
Vitaly V. DEMIDOCHKIN
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchange ◽  
Wall Temperature ◽  
Arithmetic Means ◽  
Average Value ◽  
Average Temperature ◽  
Coeffi Cients ◽  
Heat Transfer Coeffi ◽  
Recuperative Heat Exchanger

This article discusses the issue of determining the value the average wall temperature of the plate of a recuperative heat exchanger type “air-to-air” with a corrugated mesh insert based on the results processing the data of a physical experiment to determine the thermohydraulic characteristics such heat exchange surfaces. It has been established that the temperature fi eld of heat exchange surfaces of this type is nonuniform, depends on the conditions of heat exchange and hydraulic regimes of air fl ow. Therefore, the adoption of the arithmetic means value of the measured surface temperatures as the calculated average temperature of the heat exchanger wall entails signifi cant errors in the subsequent processing of experimental data and fi nal the values of the heat transfer coeffi cients, the values the Nusselt criterion and the criterion equations of heat transfer. It is proposed to determine the average value the wall temperature of the heat exchanger based on the results of measurements the wall’s temperatures, the estimate of the coordinates the center of distribution the results of measurements the wall temperatures, the equations of heat balance and heat transfer.

Aerodynamic effects of bio-inspired corrugated wings on gliding and hovering performances

2020 ◽  
pp. 095440622091799
Author(s):  
Haibin Xuan ◽  
Jun Hu ◽  
Yong Yu ◽  
Jiaolong Zhang
Keyword(s):  
Inclination Angle ◽  
Fluid Dynamic ◽  
Angle Of Attack ◽  
Aerodynamic Forces ◽  
Limited Effect ◽  
Gliding Flight ◽  
Significant Difference ◽  
Inclination Angles ◽  
Underlying Mechanisms ◽  
Lift And Drag

Recently, numerous studies have been conducted to clarify the effects of corrugation wing on aerodynamic performances. The effects of the corrugation patterns and inclination angles were investigated using computational fluid dynamic method in gliding and hovering flight at Reynolds numbers of order 104. The instantaneous aerodynamic forces and the vorticity field around the wing models were provided to research the underlying mechanisms of aerodynamic effects of corrugated wing models. The findings can be concluded as follows: (1) the corrugation patterns have different effects on aerodynamic performance. The effect of noncamber corrugated wing is to decrease the lift and increase drag compared with a flat-plate when the angle of attack is less than 25° during gliding flight. The corrugated wing with a camber (corrug-2) after the valleys enhances the aerodynamic forces when angle of attack is higher than 35°. The valley inclination angle has limited effect on aerodynamic forces in gliding flight. (2) The lift forces of different corrugation patterns show significantly asymmetric during the upstroke and downstroke. The main reason leads to this phenomenon is the case that two sides of the corrugated wings are not symmetric around the pitching axis. The corrugated wing with only two valleys (corrug-1) changes the lift and drag very slightly. Corrug-2 produces larger peak during downstroke and smaller peak during upstroke. The increase in the inclination angle has limited effect on the aerodynamic forces. The possible reason for these small aerodynamic effects might be that the corrugated wings are smoothed by small vortices trapped in valleys. The main reason for the significant difference between plate and corrug-2 is that the recirculating vortices trapped in the saddle and hump reduce the pressure above the wing surface.

Effect of Fluke Inclination on Behavior of Drag Anchor in Uniform Clay Under Unidirectional and Combined Loading

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Xiaoni Wu ◽  
Yean Khow Chow ◽  
Chun Fai Leung
Keyword(s):  
Inclination Angle ◽  
Promising Method ◽  
Combined Loading ◽  
Embedment Depth ◽  
Practical Case ◽  
Depth Ratio ◽  
Envelope Method ◽  
Inclination Angles ◽  
Selection Of ◽  
Shape And Size

Prediction of trajectory of drag anchor is important for the design and selection of drag anchor. Prediction based on yield envelope characterizing the anchor behavior under combined loading provides a promising method. However, the existing application of the yield envelope method ignores the effect of the fluke inclination angle by assuming a horizontally placed anchor fluke. This study aims to investigate the behavior of inclined fluke, which is the practical case during installation. The effects of the fluke inclination angle and embedment depth ratio on the anchor behavior in uniform clay under unidirectional loading and combined loading are investigated. It is found that the effect of the fluke inclination angle on the unidirectional capacity factors is mainly for anchor with embedment depth ratio less than 3. This results in the large difference of the size of the yield envelopes for fluke with same smaller embedment depth ratio but different fluke inclination angle, while the effect is minor on the shape of the yield envelope for such cases. However, there is large difference in the shape and size of the shallow yield envelopes for fluke with different embedment depth ratios and inclination angles.

scholarly journals Bayesian hierarchical inference of asteroseismic inclination angles

2019 ◽  
Vol 488 (1) ◽  
pp. 572-589 ◽  
Author(s):  
James S Kuszlewicz ◽  
William J Chaplin ◽  
Thomas S H North ◽  
Will M Farr ◽  
Keaton J Bell ◽  
...  
Keyword(s):  
Inclination Angle ◽  
Angle Distribution ◽  
Data Set ◽  
Single Star ◽  
Bayesian Hierarchical ◽  
Hierarchical Method ◽  
Giant Stars ◽  
Inclination Angles ◽  
Red Giant Stars ◽  
Red Giant

Abstract The stellar inclination angle – the angle between the rotation axis of a star and our line of sight – provides valuable information in many different areas, from the characterization of the geometry of exoplanetary and eclipsing binary systems to the formation and evolution of those systems. We propose a method based on asteroseismology and a Bayesian hierarchical scheme for extracting the inclination angle of a single star. This hierarchical method therefore provides a means to both accurately and robustly extract inclination angles from red giant stars. We successfully apply this technique to an artificial data set with an underlying isotropic inclination angle distribution to verify the method. We also apply this technique to 123 red giant stars observed with Kepler. We also show the need for a selection function to account for possible population-level biases, which are not present in individual star-by-star cases, in order to extend the hierarchical method towards inferring underlying population inclination angle distributions.

scholarly journals An experimental study on the effect of tool geometry on tool wear and surface roughness in hard turning

2020 ◽  
Vol 12 (9) ◽  
pp. 168781402095988
Author(s):  
Pham Minh Duc ◽  
Le Hieu Giang ◽  
Mai Duc Dai ◽  
Do Tien Sy
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Inclination Angle ◽  
Hard Turning ◽  
Rake Angle ◽  
Machining Process ◽  
Tool Geometry ◽  
Standard Tool ◽  
Inclination Angles ◽  
Mixed Ceramic

The main purpose of this study is to investigate the influence of tool geometry (cutting edge angle, rake angle, and inclination angle) and to optimize tool wear and surface roughness in hard turning of AISI 1055 (52HRC) hardened steel by using TiN coated mixed ceramic inserts. The results show that the inclination angle is the major factor affecting the tool wear and the surface roughness in hard turning. With the increase in negative rake and inclination angles, the tool wear decreases, and the surface roughness increases. However, the surface roughness will decrease when the inclination angle increases to overpass a certain limit. This is a new and significant point in the research of the hard turning process. From this result, the large negative inclination angle (λ = −10°) should be applied to reduce the surface roughness and the tool wear simultaneously. With the optimal cutting tool angles in the research, the hard machining process is improved remarkably with decreases of surface roughness and tool wear 8.3% and 41.3%, respectively in comparison with the standard tool angles. And the proposed tool-post design approach brings an effective method to change the tool insert angles using standard tool-holders to improve hard or other difficult-to-cut materials turning quality.

Sign in / Sign up

Export Citation Format

Share Document