scholarly journals Mathematical Model of a Sun-Tracked Parabolic Trough Collector and Its Verification

Energies ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 4168
Author(s):  
Wiesław Zima ◽  
Artur Cebula ◽  
Piotr Cisek
Keyword(s):  
Working Fluid ◽  
Energy Yield ◽  
Measured Temperature ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
Ansys Fluent ◽  
Model Calculations ◽  
Parabolic Trough Collector ◽  
One Dimensional ◽  
Heat Intake

The paper presents a one-dimensional distributed parameter model for simulating the transient-state operation of a parabolic trough collector (PTC). The analyzed solar collector has a module design and is equipped with a two-axis sun-tracking system to increase the solar energy yield. The single module is composed of an evacuated tube and a set of parabolic mirrors acting as reflectors. In each of the collector tubes, two aluminum U-tubes are installed, enabling heat intake by the solar fluid. The collector is intended for household applications, as well as other medium thermal energy demand uses. During the numerical model development, appropriate energy balance differential equations are formulated for the collector individual components. The equations are solved using different schemes. As a result, a time- and space-dependent temperature series for each of the collector components and the working fluid are obtained. To select an appropriate time and spatial steps for the developed model and to verify the reliability of the results received, the collector model is also implemented in ANSYS Fluent. The results of the one-dimensional model calculations and comparisons carried out in ANSYS demonstrate considerable agreement. In particular, the values of the fluid temperature at the collector outlet, calculated using the model developed, show high consistency with the ANSYS Fluent results. Furthermore, a preliminary experimental verification of the proposed model is carried out on a test stand currently under construction. The computed and measured temperature course of the fluid at the collector outlet is compared. In this case, the results are also satisfactory.

scholarly journals EXPERIMENTAL INVESTIGATIONS OF A SOLAR PARABOLIC TROUGH COLLECTOR FOR CIRCULAR AND ELLIPTICAL ABSORBER

2017 ◽  
Vol 13 (7) ◽  
pp. 6348-6355
Author(s):  
Suresh. R ◽  
Subash Chandra Bose.R ◽  
Arumugam. K ◽  
Anbazhagan. R ◽  
Sathiyamoorthy. V ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Energy Demand ◽  
Transfer Rate ◽  
Working Fluid ◽  
Experimental Investigations ◽  
Outlet Temperature ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
Parabolic Trough Collector

             Solar parabolic trough collector is one of the most efficient and an effective technology to deal with environmental pollution and it has gained much attention due to the recent energy demand. The solar parabolic trough collector is one of the most promising techniques for absorbing the heat from the sun. This heat is utilized for electricity generation and other industrial heating applications. This paper describes the theoretical and experimental assessment of performance of the circular and elliptical absorbers used in solar parabolic trough collector. The absorber tube of parabolic trough collector is used to transfer the heat to the working fluid. The working fluid considered over here is water which is the best operating medium in direct steam generation. The mass flow rate of water in absorber tube is analyzed in 3 stages as 0.016, 0.024 and 0.030 kg/s respectively. The experimental test is done in Chennai-Tamilnadu, Southern part of India which experiences a superior temperature throughout the year. The experiment is conducted for the period of one year from June 2015 to May 2016. The performance improvement focuses on collector efficiency, useful heat transfer rate, outlet temperature of working fluid, temperature gradient, overall heat transfer rate and the thermal losses.

scholarly journals An Experimental Work on the Performance of Single Solar Still with Parabolic Trough Collector in Hot Climate Conditions

2021 ◽  
Vol 39 (5) ◽  
pp. 1627-1633
Author(s):  
Hawraa Fadhel ◽  
Qahtan A. Abed ◽  
Dhafer M. Hachim
Keyword(s):  
Weather Conditions ◽  
Working Fluid ◽  
Distilled Water ◽  
Fluid Temperature ◽  
Productivity Analysis ◽  
Solar Still ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Climate Conditions ◽  
Hot Climate

This study investigated the production of single slope solar still and the influence of combining with a parabolic trough collector. The effect of the different working fluid types on freshwater productivity, outlet working fluid temperature, heat gain, and thermal efficiency has been studied under the weather conditions of south city of Iraq/ Najaf (32° 1' N / 44° 1' E). The first type was water and the second type is nanofluid. The results of the comparison showed when using water as a working fluid flowing inside the receiving tube for different days; the highest temperatures were obtained at 12:00 pm, and the average productivity of distilled water was obtained in May and June 2021 were 4.5358 and 6.733 kg/m2/day respectively. While when using the nanofluid as a working fluid flowing inside the Parabolic Trough Collector (PTC) receiver tube, the outlet temperatures were rising for the same comparison days with an increase in the productivity of distilled water. Where the freshwater productivity during the day was 8.745328 kg /m2 /day as, and it was 9.018119 kg/m2/day during the other day. A productivity analysis was carried out for two different working fluid types (Water and nanofluid instead of water) as a fluid running inside the receiving tube of PTC. The freshwater produced from PTC (with nanofluid) was a 42.2% improvement in productivity compared with conventional PTC.

Development of an Innovative Code for the Design of Different Parabolic Trough Solar Fields

2009 ◽  
Author(s):  
Ennio Macchi ◽  
Giampaolo Manzolini ◽  
Paolo Silva
Keyword(s):  
Solar Energy ◽  
Energy Demand ◽  
Working Fluid ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
High Solar Radiation ◽  
Power Block ◽  
The Usa ◽  
Solar Field ◽  
Steam Cycle

The role of renewable energies and in particular solar energy could be fundamental in future scenarios of worldwide increase of energy demand: thermodynamic solar energy can play an important role in country with high solar radiation. This paper discusses the development and testing of an innovative code for the prediction of thermodynamic performances at nominal conditions and the estimation of costs of the whole plant, for different parabolic trough solar fields. The code allows a preliminary design of the solar field lay-out, the sizing of the main components of the plant and the optimization of the steam cycle. The code, named PATTO (PArabolic Trough Thermodynamic Optimization), allows to separately calculate the thermal efficiency of (i) parabolic trough systems in commerce as well as (ii) combination of components of various commercial systems, in order to exploit different technology solutions: combination of mirrors, receivers and supports. Using the selected parabolic troughs, the plant configuration is then completed by connecting pipes, heat exchangers, the steam cycle, and storage tanks. The code is also flexible in terms of working fluid, temperature and pressure range. Regarding the power block, a conventional steam cycle with super-heater and re-heater sections and up to seven regenerative bleedings is adopted. It is possible to use also simpler configuration as without re-heater or with less regenerative bleedings. Moreover, thanks to simple or sophisticated economic correlations depending on available data, the code calculates the overall investment cost for the considered solar field and the power block. The code performs steady state analysis at nominal conditions, while future developments are planned regarding part load analysis and transient simulations. The model is tested towards real applications and reference values found in literature; in particular, focusing on SEGS VI plant in the USA. Detailed results showing code potentiality, are presented in terms of solar field and power block energy balances, plant auxiliaries, piping and economic analysis.

Dynamic Analysis of Direct Steam Generating Parabolic Trough Collector System

2020 ◽  
Vol 143 (3) ◽  
Author(s):  
C. V. Chachin Vishal ◽  
Jayaraj Krishnan ◽  
G. Venkatesan ◽  
V. Samson Packiaraj Raphael ◽  
Purnima Jalihal
Keyword(s):  
Pressure Drop ◽  
Working Fluid ◽  
Maximum Pressure ◽  
Parabolic Trough ◽  
Thermal Systems ◽  
Parabolic Trough Collector ◽  
Collector System ◽  
Multi Stage ◽  
Direct Steam ◽  
Mass Flowrate

Abstract Conventional desalination technologies like multi stage flashing, multi-effect desalination (MED) using steam as motive fluid can be made sustainable by obtaining the motive steam from solar thermal systems. In this study, a transient simulation has been performed to determine the dissimilitude in pressure drop and dryness fraction, of working fluid in absorber tube due to variation in solar irradiance. A one-dimensional (1D) mathematical model has been developed using matlab for assessing the thermal performance and heat transfer characteristics of a direct steam generating (DSG) parabolic trough collector (PTC) system. It was observed that maximum pressure drop does not occur at maximum quality indicating the working conditions impair the system performance. The developed model was used to overcome this by varying both pressure and mass flowrate of working fluid in accordance to the radiation, results indicated reduction in pressure drop during the same time period for the same exit quality.

A Numerical Model for Off-Design Performance Calculation of Parabolic Trough Based Solar Power Plants

2010 ◽  
Author(s):  
Andrea Giostri ◽  
Claudio Saccilotto ◽  
Paolo Silva ◽  
Ennio Macchi ◽  
Giampaolo Manzolini
Keyword(s):  
Heat Transfer ◽  
Numerical Model ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Design Calculation ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
Design Algorithm ◽  
Energy Balances ◽  
Steam Cycle

The paper deals with the development and testing of an innovative code for the performance prediction of solar trough based CSP plants in off-design conditions. The code is developed in MS Visual Basic 6.0 with Excel as user interface. The proposed code originates from a previously presented algorithm for on-design sizing and cost estimation of the solar field lay-out, as well as of the main components of the plant, including connecting piping and the steam cycle. Off-design calculation starts from data obtained through the on-design algorithm and considers steady-state situations. Both models are implemented in the same software, named PATTO (PArabolic Trough Thermodynamic Optimization), which is very flexible: the optical-thermal model of collectors can simulate different kinds of parabolic trough systems in commerce, including a combination of various mirrors, receivers and supports. The code is also flexible in terms of working fluid, temperature and pressure range, and can also simulate direct steam generation plants (DSG). Regarding the power block, a conventional steam cycle with super-heater, eventually a re-heater section, and up to seven regenerative bleedings is adopted. The off-design model calculates thermal performance of collectors taking into account proper correlations for convective heat transfer coefficients, considering also boiling regime in DSG configurations. Solar plant heat and mass balances and performances at off-design conditions are estimated by accounting for the constraints imposed by the available heat transfer areas in heat exchangers and condenser, as well as the characteristic curve of the steam turbine. The numerical model can be used for a single calculation in a specific off-design condition, as well as for a whole year estimation of energy balances with an hourly resolution. The model is tested towards real applications and reference values found in literature; in particular, focusing on SEGS VI plant in the USA and SAM® code. Annual energy balances with ambient condition taken from TMY3 database are obtained, showing good accuracy of predicted performances. The code potentiality in the design process reveals twofold: it can be used for plant optimization in feasibility studies; moreover it is useful to find the best control strategy of a plant, especially the mass flow of heat transfer fluid in each operating condition.

Thermal and Geometrical Assessment of Parabolic Trough Collector Mounted Double Evacuated Novel Receiver Tube System

2021 ◽  
Author(s):  
Sahil Thappa ◽  
Aditya Chauhan ◽  
Yatheshth Anand ◽  
Sanjeev Anand
Keyword(s):  
Flow Rate ◽  
High Energy ◽  
Fluid Temperature ◽  
Tube System ◽  
Parabolic Trough ◽  
Efficient Operation ◽  
Parabolic Trough Collector ◽  
Design Considerations ◽  
Energy And Exergy ◽  
Double Envelope

Abstract This paper particularly aims to highlight the necessity of optimal geometric design considerations of a parabolic trough collector (PTC) mounted novel receiver tube in view of efficient operation and high-end performance. Many investigations, analysis, and validation have been done in this regard as solar energy based PTC now a commercially mature technology acknowledges a variety of role in the form of power generation and other thermal applications. This article identifies the optimal rim angle corresponding to its tube size as required for high exergetic gains. Almost six receiver tubes, distinct in terms of dimensions and number of covers are compared for their best results to be mounted on adequate geometry with different rim angle (40°, 80°, and 120°). A significant variation of flow rate (i.e. 16 to 216 litre/hr) and inlet fluid temperature (i.e. 323 K, 423 K, 523 K, 623 K, and 723 K) has been extensively detailed about high energy and exergy retrieval from the system. The study reports that all the favorable results are found with the receiver tube having a diameter of 0.027 m and a double envelope, compared to other design considerations. Results show that as the flow rate increases energy efficiency also increases up to some extent along with increasing receiver tube temperature. The highest energy and exergy efficiency as reported to be 79.4% and 47% respectively with 80o being the optimal rim angle for a 5.7 m wide parabolic aperture.

Sign in / Sign up

Export Citation Format

Share Document