scholarly journals Analysis of Diesel Knock for High-Altitude Heavy-Duty Engines Using Optical Rapid Compression Machines

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3080
Author(s):  
Xiangting Wang ◽  
Haiqiao Wei ◽  
Jiaying Pan ◽  
Zhen Hu ◽  
Zeyuan Zheng ◽  
...  
Keyword(s):  
High Altitude ◽  
High Speed ◽  
Ambient Pressure ◽  
Critical Conditions ◽  
Heavy Duty ◽  
Pressure Oscillations ◽  
Spray Impingement ◽  
Rapid Compression ◽  
The Given ◽  
Injection Pressures

In high altitude regions, affected by the low-pressure and low-temperature atmosphere, diesel knock is likely to be encountered in heavy-duty engines operating at low-speed and high-load conditions. Pressure oscillations during diesel knock are commonly captured by pressure transducers, while there is a lack of direct evidence and visualization images, such that its fundamental formation mechanism is still unclear. In this study, optical experiments on diesel knock with destructive pressure oscillations were investigated in an optical rapid compression machine. High-speed direct photography and simultaneous pressure acquisition were synchronically performed, and different injection pressures and ambient pressures were considered. The results show that for the given ambient temperature and pressure, diesel knock becomes prevalent at higher injection pressures where fuel spray impingement becomes enhanced. Higher ambient pressure can reduce the tendency to diesel knock under critical conditions. For the given injection pressure satisfying knocking combustion, knock intensity is decreased as ambient pressure is increased. Further analysis of visualization images shows diesel knock is closely associated with the prolonged ignition delay time due to diesel spray impingement. High-frequency pressure oscillation is caused by the propagation of supersonic reaction-front originating from the second-stage autoignition of mixture. In addition, the oscillation frequencies are obtained through the fast Fourier transform (FFT) analysis.

scholarly journals Analysis of Diesel Knock for High-Altitude Heavy-Duty Engines Using Optical Rapid Compression Machines

2021 ◽  
Author(s):  
Xiangting Wang ◽  
Haiqiao Wei ◽  
Jiaying Pan ◽  
Zhen Hu ◽  
Xuan Wang ◽  
...  
Keyword(s):  
High Altitude ◽  
Heavy Duty ◽  
Rapid Compression

Robust Identification of Pressure Oscillations in the Combustion Chamber of a Heavy-Duty Turbine

2017 ◽  
Author(s):  
Juliano Pierezan ◽  
Gabriel Maidl ◽  
Eduardo Yamao ◽  
João Paulo Silva Gonçalves ◽  
Flávio Chiesa ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Heavy Duty ◽  
Pressure Oscillations ◽  
Robust Identification

ELECTRITE COBALT

Alloy Digest ◽  
1960 ◽  
Vol 9 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Heat Treating ◽  
Heavy Duty ◽  
Steel Company

Abstract ELECTRITE COBALT is a 5% cobalt type high-speed steel recommended for heavy duty cutting tools. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-89. Producer or source: Latrobe Steel Company.

CYCLOPS M4

Alloy Digest ◽  
1978 ◽  
Vol 27 (7) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Abrasion Resistance ◽  
High Speed ◽  
Heat Treating ◽  
Heavy Duty ◽  
Maximum Hardness ◽  
Temperature Performance ◽  
Sharp Edges ◽  
Normal Carbon

Abstract CYCLOPS M4 is a deep-hardening steel that was developed to utilize the excellent abrasion resistance that results from higher-than-normal carbon and vanadium contents in the molybdenum-tungsten family of high-speed steels. It is recommended for heavy-duty cutting operations and for sharp edges for fine cuts. Cyclops M4 should always be used at or near maximum hardness. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: TS-335. Producer or source: Cyclops Corporation.

A 2 × 20 Gbps hybrid MDM-OFDM–based high-altitude platform-to-satellite FSO transmission system

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Vel Murugan Gomathy ◽  
T. V. Paramasivam Sundararajan ◽  
C. Sengodan Boopathi ◽  
Pandiyan Venkatesh Kumar ◽  
Krishnamoorthy Vinoth Kumar ◽  
...  
Keyword(s):  
High Altitude ◽  
Orthogonal Frequency Division Multiplexing ◽  
High Speed ◽  
Satellite Communication ◽  
Input Power ◽  
Transmission System ◽  
Communication Link ◽  
Space Optics ◽  
High Altitude Platform ◽  
Mode Division Multiplexing

AbstractIn the present study, the application of free space optics (FSO) transmission system to realize a long-reach high-altitude platform (HAP)-to-satellite communication link has been exploited. High-speed information transmission without interference is accomplished using orthogonal frequency division multiplexing (OFDM). Further, the information capacity of the proposed system is increased by employing mode division multiplexing (MDM). We have investigated the proposed MDM-OFDM-HAP-to-satellite FSO transmission system performance over varying FSO range, diameter of the receiver, pointing errors, and input power. Also, an improved transmission performance of the proposed system using a square root module is reported.

scholarly journals CFD Simulation of a Hyperloop Capsule Inside a Low-Pressure Environment Using an Aerodynamic Compressor as Propulsion and Drag Reduction Method

2021 ◽  
Vol 11 (9) ◽  
pp. 3934
Author(s):  
Federico Lluesma-Rodríguez ◽  
Temoatzin González ◽  
Sergio Hoyas
Keyword(s):  
Shock Waves ◽  
Power Consumption ◽  
High Speed ◽  
Cfd Simulation ◽  
Aerodynamic Drag ◽  
Flow Behavior ◽  
Critical Conditions ◽  
Vehicle Speed ◽  
Blockage Ratio ◽  
The Cost

One of the most restrictive conditions in ground transportation at high speeds is aerodynamic drag. This is even more problematic when running inside a tunnel, where compressible phenomena such as wave propagation, shock waves, or flow blocking can happen. Considering Evacuated-Tube Trains (ETTs) or hyperloops, these effects appear during the whole route, as they always operate in a closed environment. Then, one of the concerns is the size of the tunnel, as it directly affects the cost of the infrastructure. When the tube size decreases with a constant section of the vehicle, the power consumption increases exponentially, as the Kantrowitz limit is surpassed. This can be mitigated when adding a compressor to the vehicle as a means of propulsion. The turbomachinery increases the pressure of part of the air faced by the vehicle, thus delaying the critical conditions on surrounding flow. With tunnels using a blockage ratio of 0.5 or higher, the reported reduction in the power consumption is 70%. Additionally, the induced pressure in front of the capsule became a negligible effect. The analysis of the flow shows that the compressor can remove the shock waves downstream and thus allows operation above the Kantrowitz limit. Actually, for a vehicle speed of 700 km/h, the case without a compressor reaches critical conditions at a blockage ratio of 0.18, which is a tunnel even smaller than those used for High-Speed Rails (0.23). When aerodynamic propulsion is used, sonic Mach numbers are reached above a blockage ratio of 0.5. A direct effect is that cases with turbomachinery can operate in tunnels with blockage ratios even 2.8 times higher than the non-compressor cases, enabling a considerable reduction in the size of the tunnel without affecting the performance. This work, after conducting bibliographic research, presents the geometry, mesh, and setup. Later, results for the flow without compressor are shown. Finally, it is discussed how the addition of the compressor improves the flow behavior and power consumption of the case.

scholarly journals Interactive Effects in Two-Droplets Combustion of RP-3 Kerosene under Sub-Atmospheric Pressure

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1229
Author(s):  
Hongtao Zhang ◽  
Zhihua Wang ◽  
Yong He ◽  
Jie Huang ◽  
Kefa Cen
Keyword(s):  
Burning Rate ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Ambient Pressure ◽  
Interactive Effects ◽  
Propagation Time ◽  
High Speed Camera ◽  
Single Droplet ◽  
Fuel Droplets ◽  
Spacing Distance

To improve our understanding of the interactive effects in combustion of binary multicomponent fuel droplets at sub-atmospheric pressure, combustion experiments were conducted on two fibre-supported RP-3 kerosene droplets at pressures from 0.2 to 1.0 bar. The burning life of the interactive droplets was recorded by a high-speed camera and a mirrorless camera. The results showed that the flame propagation time from burning droplet to unburned droplet was proportional to the normalised spacing distance between droplets and the ambient pressure. Meanwhile, the maximum normalised spacing distance from which the left droplet can be ignited has been investigated under different ambient pressure. The burning rate was evaluated and found to have the same trend as the single droplet combustion, which decreased with the reduction in the pressure. For every experiment, the interactive coefficient was less than one owing to the oxygen competition, except for the experiment at L/D0 = 2.5 and P = 1.0 bar. During the interactive combustion, puffing and microexplosion were found to have a significant impact on secondary atomization, ignition and extinction.

Development and Validation of a Three-Dimensional Multiphase Flow CFD Analysis for Journal Bearings in Steam and Heavy Duty Gas Turbines

2012 ◽  
Author(s):  
Stephan Uhkoetter ◽  
Stefan aus der Wiesche ◽  
Michael Kursch ◽  
Christian Beck
Keyword(s):  
Experimental Data ◽  
Multiphase Flow ◽  
Gas Turbines ◽  
High Speed ◽  
Three Dimensional ◽  
Air Entrainment ◽  
Journal Bearings ◽  
Heavy Duty ◽  
Present Contribution ◽  
Two Phase

The traditional method for hydrodynamic journal bearing analysis usually applies the lubrication theory based on the Reynolds equation and suitable empirical modifications to cover turbulence, heat transfer, and cavitation. In cases of complex bearing geometries for steam and heavy-duty gas turbines this approach has its obvious restrictions in regard to detail flow recirculation, mixing, mass balance, and filling level phenomena. These limitations could be circumvented by applying a computational fluid dynamics (CFD) approach resting closer to the fundamental physical laws. The present contribution reports about the state of the art of such a fully three-dimensional multiphase-flow CFD approach including cavitation and air entrainment for high-speed turbo-machinery journal bearings. It has been developed and validated using experimental data. Due to the high ambient shear rates in bearings, the multiphase-flow model for journal bearings requires substantial modifications in comparison to common two-phase flow simulations. Based on experimental data, it is found, that particular cavitation phenomena are essential for the understanding of steam and heavy-duty type gas turbine journal bearings.

Effect of Pressure on Bubble Growth Within Liquid Droplets at the Superheat Limit

1982 ◽  
Vol 104 (4) ◽  
pp. 750-757 ◽  
Author(s):  
C. T. Avedisian
Keyword(s):  
Vapor Bubble ◽  
Bubble Growth ◽  
High Speed ◽  
Ambient Pressure ◽  
Organic Liquid ◽  
Liquid Droplets ◽  
Growth Data ◽  
Two Phase ◽  
Photographic Evidence ◽  
Good Agreement

A study of high-pressure bubble growth within liquid droplets heated to their limits of superheat is reported. Droplets of an organic liquid (n-octane) were heated in an immiscible nonvolatile field liquid (glycerine) until they began to boil. High-speed cine photography was used for recording the qualitative aspects of boiling intensity and for obtaining some basic bubble growth data which have not been previously reported. The intensity of droplet boiling was found to be strongly dependent on ambient pressure. At atmospheric pressure the droplets boiled in a comparatively violent manner. At higher pressures photographic evidence revealed a two-phase droplet configuration consisting of an expanding vapor bubble beneath which was suspended a pool of the vaporizing liquid. A qualitative theory for growth of the two-phase droplet was based on assuming that heat for vaporizing the volatile liquid was transferred across a thin thermal boundary layer surrounding the vapor bubble. Measured droplet radii were found to be in relatively good agreement with predicted radii.

SIMULATION SCHEME MODELING OF THE SUPER-SPEED TIME BUFFER

2020 ◽  
Author(s):  
А.М. САЖНЕВ ◽  
Л.Г. РОГУЛИНА
Keyword(s):  
High Speed ◽  
High Efficiency ◽  
Low Cost ◽  
Circuit Modeling ◽  
Clock Signal ◽  
Behavioral Models ◽  
Software Environment ◽  
Time Buffer ◽  
The Given ◽  
Simulation Scheme

Приводятся результаты моделирования сверхскоростного буфера тактовых сигналов, выполненного на базе арсенид-галлиевых n-канальных транзисторов в среде OrCAD и полностью отвечающего следующим требованиям: высокие технические характеристики, малые размеры, высокая частота и КПД, гибкость применения. Приведенные поведенческие модели допускают использование любой программной среды по схемотехническому моделированию. The results of simulation of an ultra-high-speed clock signal buffer based on gallium arsenide n-channel transistors in OrCAD are presented, which fully meets the following requirements: high technical characteristics, application flexibility, low cost, small size, high frequency, and high efficiency. The given behavioral models allow the use of any software environment for circuit modeling.

Sign in / Sign up

Export Citation Format

Share Document