scholarly journals Influence of the Perovskite La0.8Sr0.2Mn0.5Co0.5O3-δ on the Electrochemical Performance of the Graphene-Based Supercapacitor

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3030
Author(s):  
Bo-Min Kim ◽  
Hyo-Young Kim ◽  
Young-Wan Ju ◽  
Jeeyoung Shin
Keyword(s):  
Specific Capacitance ◽  
Storage System ◽  
Energy System ◽  
Energy Storage System ◽  
Cycling Performance ◽  
Storage Device ◽  
Supercapacitor Electrode ◽  
Perovskite Material ◽  
Ion Conducting ◽  
Oxide Ion

A supercapacitor is a potential energy system that will be a part of an efficient storage device of renewable energy, such as a small battery and a large energy storage system (ESS), etc. However, a lot of efforts have been devoted to improving stability. Generally, ABO3-type perovskite structure has been studied as an electrode and/or an oxide ion-conducting electrolyte for solid oxide fuel cells with stable structural stability at high temperatures. In this study, perovskite material (La0.8Sr0.2Mn0.5Co0.5O3-δ. LSMCO) was added as a component of the supercapacitor electrode for enhanced stability. According to electrochemical measurements, at 5 mV/s, the specific capacitance of the graphene-based electrode (G95) is 68 F/g, and the electrode mixed with perovskite (G70L25) is 55 F/g. Nonetheless, the standard deviation of the capacitance value of G70L25 is smaller than that of G95. Alongside this, the G70L25 electrode showed that specific capacitance decreased in the cycling test, but, for the G95 electrode, the specific capacitance after the 4990th cycle increased or decreased, resulting in unpredictable results. Therefore, perovskite added electrode (G70L25) shows higher stability compared to the graphene nanoplatelets electrode (G95) in both initial and cycling performance, albeit a lower specific capacitance.

Wind-Solar-Hydrogen Hybrid Energy Control Strategy Considering Delayed Power of Hydrogen Production

2021 ◽  
Vol 69 (2) ◽  
pp. 5-12
Author(s):  
Zheng Li ◽  
Yan Qin ◽  
Xin Cao ◽  
Shaodong Hou ◽  
Hexu Sun
Keyword(s):  
Energy Storage ◽  
Control Strategy ◽  
Reactive Power ◽  
Storage System ◽  
Energy Storage System ◽  
Storage Device ◽  
Solar Hydrogen ◽  
Dc Voltage ◽  
Hybrid Energy ◽  
Load Demand

In order to meet the load demand of power system, BP based on genetic algorithm is applied to the typical daily load forecasting in summer. The demand change of summer load is analysed. Simulation results show the accuracy of the algorithm. In terms of power supply, the reserves of fossil energy are drying up. According to the prediction of authoritative organizations, the world's coal can be mined for 216 years. As a renewable energy, wind power has no carbon emissions compared with traditional fossil energy. At present, it is generally believed that wind energy and solar energy are green power in the full sense, and they are inexhaustible clean power. The model of wind power solar hydrogen hybrid energy system is established. The control strategy of battery power compensation for delayed power of hydrogen production is adopted, and different operation modes are divided. The simulation results show that the system considering the control strategy can well meet the load demand. Battery energy storage system is difficult to respond to short-term peak power fluctuations. Super capacitor is used to suppress it. This paper studies the battery supercapacitor complementary energy storage system and its control strategy. When the line impedance of each generation unit in power grid is not equal, its output reactive power will be affected by the line impedance and distributed unevenly. A droop coefficient selection method of reactive power sharing is proposed. Energy storage device is needed to balance power and maintain DC voltage stability in the DC side of microgrid. Therefore, a new droop control strategy is proposed. By detecting the DC voltage, dynamically translating the droop characteristic curve, adjusting the output power, maintaining the DC voltage in a reasonable range, reducing the capacity of the DC side energy storage device. Photovoltaic grid connected inverter chooses the new droop control strategy.

scholarly journals Case study of stationary energy storage device in a 3 kV DC traction system

2018 ◽  
Vol 180 ◽  
pp. 02005 ◽  
Author(s):  
Włodzimierz Jefimowski ◽  
Anatolii Nikitenko
Keyword(s):  
Energy Storage ◽  
Storage System ◽  
Energy Storage System ◽  
Energy Utilization ◽  
Storage Device ◽  
Location Selection ◽  
Train Operation ◽  
Traction Substations ◽  
Traction System ◽  
Regenerative Energy

The paper presents the results of economic study of energy storage system (ESS) implemented in 3 kV DC power supply system. Two conceptions of ESS have been investigated: ESS with supercapacitor (SC) and hybrid ESS (HESS) with SC and LFP battery. The investigated locations of energy storage systems are considered among existing traction substations in two railway lines with different density of train operation. The considered aims of energy storage system implementation are decreasing of energy consumption by maximum regenerative energy utilization and reduction of peak 15- min power demand of traction substation. The paper presents a method of regenerative power estimation depending on the location of the considered ESS implementation point. Also the method of optimal location selection of ESS in terms of minimization of Simple Payback Time (SPBT) of investment is presented. Besides the influence of initial cost value as well as energy price on the SPBT value are investigated. The results are compared between two railway lines with different number of trains operating.

scholarly journals An extensive review of energy storage system for the residential renewable energy system

2020 ◽  
Vol 18 (1) ◽  
pp. 242
Author(s):  
M. S. A. Mustaza ◽  
M. A. M. Ariff ◽  
Sofia Najwa Ramli
Keyword(s):  
Renewable Energy ◽  
Energy Storage ◽  
Power System ◽  
Storage System ◽  
Energy Condition ◽  
Energy System ◽  
Energy Storage System ◽  
Energy Utilization ◽  
Constant Current ◽  
Battery Management System

Energy storage system (ESS) plays a prominent role in renewable energy (RE) to overcome the intermittent of RE energy condition and improve energy utilization in the power system. However, ESS for residential applications requires specific and different configuration. Hence, this review paper aims to provide information for system builders to decide the best setup configuration of ESS for residential application. In this paper, the aim is to provide an insight into the critical elements of the energy storage technology for residential application. The update on ESS technology, battery chemistry, battery charging, and monitoring system and power inverter technology are reviewed. Then, the operation, the pro, and cons of each variant of these technologies are comprehensively studied. This paper suggested that the ESS for residential ESS requires NMC battery chemistry because it delivers an all-rounded performance as compared to other battery chemistries. The four-stages constant current (FCC) charging technique is recommended because of the fast charging capability and safer than other charging techniques reviewed. Next, the battery management system (BMS) is recommended to adapt in advance machine learning method to estimate the state of charge (SOC), state of health (SOH) and internal temperature (IT) to increase the safety and prolong the lifespan of the batteries. Finally, these recommendations and solutions aimed to improve the utilization of RE energy in power system, especially in residential ESS application and offer the best option that is available on the shelf for the residential ESS application in the future.

scholarly journals Finite element modelling of an energy-geomembrane underground pumped hydroelectric energy storage system

2020 ◽  
Vol 205 ◽  
pp. 07001
Author(s):  
Hans Henning Stutz ◽  
Peter Norlyk ◽  
Kenneth Sørensen ◽  
Lars Vabbersgaard Andersen ◽  
Kenny Kataoka Sørensen ◽  
...  
Keyword(s):  
Finite Element ◽  
Energy Storage ◽  
Storage System ◽  
Constitutive Models ◽  
Energy System ◽  
Energy Storage System ◽  
Elastic Model ◽  
Hydroelectric Energy ◽  
Linear Elastic ◽  
Soil Behaviour

The increasing need for energy storage technology has led to a massive interest in novel energy storage methods. The energy geomembrane system is such a novel energy storage method. The concept of the system is briefly introduced, and a holistic numerical model of the system is presented. The model uses advanced finite-element techniques to model the energy storage system using fluid cavity elements. The developed geomembrane energy system is modelled with different constitutive models to represent the soil behaviour: a linear elastic model, a nonlinear Mohr-Coulomb model, and a hypoplastic constitutive model. The consequences of these different models on the results are studied. Hereby, the focus is the first inflation and deflation cycle of the system.

Analysis of Thermal Performance of Energy Storage System

2016 ◽  
Vol 824 ◽  
pp. 371-378
Author(s):  
Martina Jurigova ◽  
Maria Minarova ◽  
Ivan Chmúrny
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Storage System ◽  
Energy System ◽  
Energy Storage System ◽  
Advanced Technology ◽  
Winter Period ◽  
Concrete Tank ◽  
Effective Use

Thermal energy is necessary of many reasons. The most basic and most obvious includes food preparation and delivery of heat. Thermal energy storage is actually a temporary storage at high temperatures, respectively at low temperatures. It is an advanced technology, which can reduce environmental impact and it can facilitate more efficient and cleaner energy system. Nowadays, these systems have ability to retain thermal energy for a period of three months or more. The aim of design of these systems is to keep the thermal energy in summer period and to use it for heating in winter period. The role of such storage systems is to accumulate the heat, to balance temperature differences and to achieve the most effective use of the collected energy. This paper is focused on thermal analysis of system, which contains concrete tank. It is a system with water as a storage medium and the cooling of the water was monitored for 30 days.

scholarly journals The Evaluation of Feasibility of Thermal Energy Storage System at Riga TPP-2

2015 ◽  
Vol 52 (6) ◽  
pp. 22-37 ◽  
Author(s):  
P. Ivanova ◽  
O. Linkevics ◽  
A. Cers
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Production ◽  
Storage System ◽  
Energy System ◽  
Energy Storage System ◽  
Thermal Energy Storage System ◽  
Production Flexibility ◽  
Power Plant Operation

Abstract The installation of thermal energy storage system (TES) provides the optimisation of energy source, energy security supply, power plant operation and energy production flexibility. The aim of the present research is to evaluate the feasibility of thermal energy system installation at Riga TPP–2. The six modes were investigated: four for non-heating periods and two for heating periods. Different research methods were used: data statistic processing, data analysis, analogy, forecasting, financial method and correlation and regression method. In the end, the best mode was chosen – the increase of cogeneration unit efficiency during the summer.

Mississippi County Community College Solar Photovoltaic Total Energy Project

1979 ◽  
Author(s):  
E. M. Henry
Keyword(s):  
Community College ◽  
Energy Demand ◽  
Storage System ◽  
Vital Signs ◽  
Electrical Energy ◽  
Redox System ◽  
Energy System ◽  
Energy Storage System ◽  
Total System ◽  
Efficient Operation

Mississippi County Community College at Blytheville, Arkansas, will derive its total electrical and thermal energy demand from an actively cooled photovoltaic energy system being developed under the management of TEAM, Inc. of Springfield, Virginia. The facility has a design peak electrical requirement for 240 kw to be supplied by a 26-sun concentrating collector field that fully tracks E-W. A 2.4 megawatt-hour electrical energy storage system under consideration is an iron redox system using FeCl2 electrolyte and pressure-molded carbon/PVC electrodes. The power conditioning system will include a 300-kw solid-state inverter to furnish 480-v, three-phase, 60-Hz ac to the College, and appropriate switching to acquire utility company power in emergencies. Process control includes the capability to gather vital signs on the collectors, thermal loop, electrical storage and building demands, and to provide closed-loop tracking and all control signals for energy efficient operation of the total system.

Sign in / Sign up

Export Citation Format

Share Document