scholarly journals Influence of Rotation Speed and Air Pressure on the Down the Hole Drilling Velocity for Borehole Heat Exchanger Installation

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2716
Author(s):  
Tomasz Sliwa ◽  
Kinga Jarosz ◽  
Marc A. Rosen ◽  
Anna Sojczyńska ◽  
Aneta Sapińska-Śliwa ◽  
...  
Keyword(s):  
Heat Exchangers ◽  
Rotation Speed ◽  
Air Pressure ◽  
Hole Drilling ◽  
Rotary Drilling ◽  
Deep Wells ◽  
Drilling Technology ◽  
Direct Use ◽  
Drilling Velocity ◽  
Borehole Heat Exchangers

The relation between rotation speed, air pressure and the velocity of air-rotary drilling using the down the hole method is determined in an empirical manner. For the study, velocity measurements are obtained for combinations of the aforementioned parameters during fieldwork for the installation of borehole heat exchangers near Lublin, Poland. The tests consider three drill bit diameters—110, 127 and 140 mm; three rotational speeds—20, 40 and 60 1/min; and three air pressures—16, 20 and 24 bar. The borehole heat exchangers need 100 m deep wells. The lithology consists mainly of loess and clays to 24 m, sand and carbonate rocks to 36 m, and marls and limestone to 100 m. It is found that the highest drilling velocity is achieved when the greatest pressure is applied, while the lowest drilling velocity is connected to the lowest pressure. However, the relation between rotation speed and drilling velocity is more complex, as drilling velocity seems to be more affected by depth. Therefore, lithology can be a major factor. The results may find direct use in drilling, and provide a basis for further studies on the optimization of drilling technology.

Borehole Heat Exchangers in aquifers: simulation of the grout material impact

2016 ◽  
Vol 41 ◽  
pp. 268-271
Author(s):  
Luca Alberti ◽  
Adriana Angelotti ◽  
Matteo Antelmi ◽  
Ivana La Licata
Keyword(s):  
Heat Exchangers ◽  
Borehole Heat Exchangers

scholarly journals Low enthalpy geothermal energy: borehole heat exchangers (BHE). Geological and geothermal supervision during active construction in support of the energy certification of buildings - ESBE certification plan

2012 ◽  
Author(s):  
Lorenzo Cadrobbi ◽  
Fioroni Daniele ◽  
Alessandro Bozzoli
Keyword(s):  
Energy Conservation ◽  
Heat Exchangers ◽  
Energy Efficient ◽  
Geothermal Energy ◽  
Energy Requirements ◽  
Effective Coverage ◽  
Correct Execution ◽  
Environmental Technologies ◽  
Borehole Heat Exchangers ◽  
Ongoing Monitoring

This article draws on the experience matured while working with low-enthalpy geothermic installations both in the design and executive phase as well as ongoing monitoring, within the scope of energy conservation as it relates to building and construction. The goal is to illustrate the feasibility of adopting the ESBE certification protocol (Certification of Energy Efficient Low-Enthalpy Probes) aimed at optimizing the harnessing of local geothermic resources to satisfy the energy requirements of a building, measured against the initial investment. It is often the case, in fact, that during the course of a construction project for a given low-enthalpy installation, we verify incompa tibilities with the local geologic and geothermic models, which, if inadequate during construction, can compromise the proper functioning of the installation and its subsequent operation. To this end, the ESBE method, which adheres to the governing environmental regulations, and which takes its cue from technical statutes within the sector, permits us to validate via verification, simulations and tests, the geothermic field probes used in construction in an objective and standardized manner, thereby joining and supporting the most recent protocols for energy certification of buildings (LEED 2010, CASACLIMA 2011, UE 20120/31 Directive). ESBE certification operates through a dedicated Certifying Entity represented by the REET unit (Renewable Energies and Environmental Technologies) of FBK (Bruno Kessler Foundation) of Trento. The results obtained by applying the ESBE method to two concrete cases, relative to two complex geothermic systems, demonstrate how this protocol is able to guarantee, beyond the correct execution in the field of geothermic probes, an effective coverage of the energy requirements of the building during construction adopting the best optimization measures for the probes in keeping with the local geological and geothermic model.

scholarly journals Geothermal Boreholes in Poland—Overview of the Current State of Knowledge

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3251
Author(s):  
Tomasz Sliwa ◽  
Aneta Sapińska-Śliwa ◽  
Andrzej Gonet ◽  
Tomasz Kowalski ◽  
Anna Sojczyńska
Keyword(s):  
Heat Exchangers ◽  
Oil And Gas ◽  
Produced Water ◽  
Geothermal Water ◽  
Laboratory System ◽  
Water Production ◽  
Injection Wells ◽  
Geological Conditions ◽  
Geothermal Wells ◽  
Borehole Heat Exchangers

Geothermal energy can be useful after extraction from geothermal wells, borehole heat exchangers and/or natural sources. Types of geothermal boreholes are geothermal wells (for geothermal water production and injection) and borehole heat exchangers (for heat exchange with the ground without mass transfer). The purpose of geothermal production wells is to harvest the geothermal water present in the aquifer. They often involve a pumping chamber. Geothermal injection wells are used for injecting back the produced geothermal water into the aquifer, having harvested the energy contained within. The paper presents the parameters of geothermal boreholes in Poland (geothermal wells and borehole heat exchangers). The definitions of geothermal boreholes, geothermal wells and borehole heat exchangers were ordered. The dates of construction, depth, purposes, spatial orientation, materials used in the construction of geothermal boreholes for casing pipes, method of water production and type of closure for the boreholes are presented. Additionally, production boreholes are presented along with their efficiency and the temperature of produced water measured at the head. Borehole heat exchangers of different designs are presented in the paper. Only 19 boreholes were created at the Laboratory of Geoenergetics at the Faculty of Drilling, Oil and Gas, AGH University of Science and Technology in Krakow; however, it is a globally unique collection of borehole heat exchangers, each of which has a different design for identical geological conditions: heat exchanger pipe configuration, seal/filling and shank spacing are variable. Using these boreholes, the operating parameters for different designs are tested. The laboratory system is also used to provide heat and cold for two university buildings. Two coefficients, which separately characterize geothermal boreholes (wells and borehole heat exchangers) are described in the paper.

Research on the air pressure drop in plate finned tube heat exchangers

2006 ◽  
Vol 29 (7) ◽  
pp. 1138-1143 ◽  
Author(s):  
Branislav M. Jacimovic ◽  
Srbislav B. Genic ◽  
Boris R. Latinovic
Keyword(s):  
Pressure Drop ◽  
Heat Exchangers ◽  
Finned Tube ◽  
Air Pressure
Sign in / Sign up

Export Citation Format

Share Document