scholarly journals Critical Analysis of Process Integration Options for Joule-Cycle and Conventional Heat Pumps

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 635 ◽  
Author(s):  
Limei Gai ◽  
Petar Sabev Varbanov ◽  
Timothy Gordon Walmsley ◽  
Jiří Jaromír Klemeš
Keyword(s):  
Heat Pump ◽  
Process Integration ◽  
Waste Heat ◽  
Correct Choice ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Large Temperature ◽  
Temperature Changes ◽  
Application Range ◽  
Source And Sink

To date, research on heat pumps (HP) has mainly focused on vapour compression heat pumps (VCHP), transcritical heat pumps (TCHP), absorption heat pumps, and their heat integration with processes. Few studies have considered the Joule cycle heat pump (JCHP), which raises several questions. What are the characteristics and specifics of these different heat pumps? How are they different when they integrate with the processes? For different processes, which heat pump is more appropriate? To address these questions, the performance and integration of different types of heat pumps with various processes have been studied through Pinch Methodology. The results show that different heat pumps have their own optimal application range. The new JCHP is suitable for processes in which the temperature changes of source and sink are both massive. The VCHP is more suitable for the source and sink temperatures, which are near-constant. The TCHP is more suitable for sources with small temperature changes and sinks with large temperature changes. This study develops an approach that provides guidance for the selection of heat pumps by applying Process Integration to various combinations of heat pump types and processes. It is shown that the correct choice of heat pump type for each application is of utmost importance, as the Coefficient of Performance can be improved by up to an order of magnitude. By recovering and upgrading process waste heat, heat pumps can save 15–78% of the hot utility depending on the specific process.

scholarly journals To Pump or Not to Pump? Heat Pump Strategies and Payoffs

1982 ◽  
Author(s):  
Joel S. Gilbert
Keyword(s):  
Heat Flow ◽  
Heat Pump ◽  
Waste Heat ◽  
Heat Pumps ◽  
Economic Viability ◽  
Heat Sources ◽  
Hot Air ◽  
Near Term ◽  
Source And Sink

After several evaluations of waste heat sources and designing heat pumps to recover energy, it has become very apparent that there is a great deal of confusion about just what makes a heat pump economic. The purpose of this article is to look into the design and economics of heat pump systems to determine what makes certain heat pump applications winners and others losers. Steam recompression and generation of steam from moist hot air are investigated specifically. Actual commercially available equipment is considered to determine the near-term and future economic viability of each approach as a function of the source and sink temperatures and magnitude of heat flow. Paper published with permission.

scholarly journals Enhancing Heating Performance of Low-Temperature Air Source Heat Pumps Using Compressor Casing Thermal Storage

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3269 ◽  
Author(s):  
Zhongbao Liu ◽  
Fengfei Lou ◽  
Xin Qi ◽  
Yiyao Shen
Keyword(s):  
Low Temperature ◽  
Heat Pump ◽  
Waste Heat ◽  
Thermal Storage ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Discharge Temperature ◽  
Vapor Injection

Air source heat pumps (ASHPs) are widely recognized as energy-saving and environmentally friendly heating and air-conditioning equipment with broad applications. However, when conventional ASHPs are operated at a low ambient temperature, they suffer from problems such as high discharge temperature and low heating efficiency. To address these problems, this study designed a new type of dual evaporator combined with a compressor casing thermal storage heat pump system (DE-CCTS) on the basis of a low-temperature air source heat pump water heater with enhanced vapor injection (EVI). The proposed DE-CCTS used thermal storage phase change material (PCM), which was filled in the secondary evaporator (the thermal storage heat exchanger), to recover the waste heat of the compressor casing. Unlike that in the original system under different ambient temperatures, the suction temperature increased by 0.1–1 °C, the discharge temperature decreased by 0.1–0.5 °C, and the coefficient of performance (COP) of DE-CCTS increased by 0.85–4.72% under the proposed system. These effects were especially evident at low temperatures.

scholarly journals Local Heating Networks with Waste Heat Utilization: Low or Medium Temperature Supply?

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 954 ◽  
Author(s):  
Hanne Kauko ◽  
Daniel Rohde ◽  
Armin Hafner
Keyword(s):  
Low Temperature ◽  
Heat Pump ◽  
Urban Areas ◽  
Waste Heat ◽  
Local Heating ◽  
District Heating ◽  
Heat Pumps ◽  
Hot Water ◽  
Local Network ◽  
Medium Temperature

District heating enables an economical use of energy sources that would otherwise be wasted to cover the heating demands of buildings in urban areas. For efficient utilization of local waste heat and renewable heat sources, low distribution temperatures are of crucial importance. This study evaluates a local heating network being planned for a new building area in Trondheim, Norway, with waste heat available from a nearby ice skating rink. Two alternative supply temperature levels have been evaluated with dynamic simulations: low temperature (40 °C), with direct utilization of waste heat and decentralized domestic hot water (DHW) production using heat pumps; and medium temperature (70 °C), applying a centralized heat pump to lift the temperature of the waste heat. The local network will be connected to the primary district heating network to cover the remaining heat demand. The simulation results show that with a medium temperature supply, the peak power demand is up to three times higher than with a low temperature supply. This results from the fact that the centralized heat pump lifts the temperature for the entire network, including space and DHW heating demands. With a low temperature supply, heat pumps are applied only for DHW production, which enables a low and even electricity demand. On the other hand, with a low temperature supply, the district heating demand is high in the wintertime, in particular if the waste heat temperature is low. The choice of a suitable supply temperature level for a local heating network is hence strongly dependent on the temperature of the available waste heat, but also on the costs and emissions related to the production of district heating and electricity in the different seasons.

scholarly journals Heat Pump Bridge Analysis Using the Modified Energy Transfer Diagram

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 137
Author(s):  
Florian Schlosser ◽  
Heinrich Wiebe ◽  
Timothy G. Walmsley ◽  
Martin J. Atkins ◽  
Michael R. W. Walmsley ◽  
...  
Keyword(s):  
Energy Transfer ◽  
Heat Pump ◽  
Heat Recovery ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Combined Application ◽  
Recovery Potential ◽  
Composite Curve ◽  
And Performance ◽  
The Individual

Heat pumps are the key technology to decarbonise thermal processes by upgrading industrial surplus heat using renewable electricity. Existing insight-based integration methods refer to the idealised Grand Composite Curve requiring the full exploitation of heat recovery potential but leave the question of how to deal with technical or economic limitations unanswered. In this work, a novel Heat Pump Bridge Analysis (HPBA) is introduced for practically targeting technical and economic heat pump potential by applying Coefficient of Performance curves into the Modified Energy Transfer Diagram (METD). Removing cross-Pinch violations and operating heat exchangers at minimum approach temperatures by combined application of Bridge Analysis increases the heat recovery rate and reduce the temperature lift to be pumped at the same time. The insight-based METD allows the individual matching of heat surpluses and deficits of individual streams with the capabilities and performance of different market-available heat pump concepts. For an illustrative example, the presented modifications based on HPBA increase the economically viable share of the technical heat pump potential from 61% to 79%.

scholarly journals Factors Shaping A/W Heat Pumps CO₂ Emissions—Evidence from Poland

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1576
Author(s):  
Piotr Jadwiszczak ◽  
Jakub Jurasz ◽  
Bartosz Kaźmierczak ◽  
Elżbieta Niemierka ◽  
Wandong Zheng
Keyword(s):  
Air Quality ◽  
Power System ◽  
Heat Pump ◽  
Heat Pumps ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Conventional Heating ◽  
Additional Stress ◽  
The European Union ◽  
Energy Mix

Heating and cooling sectors contribute to approximately 50% of energy consumption in the European Union. Considering the fact that heating is mostly based on fossil fuels, it is then evident that its decarbonization is one of the crucial tasks for achieving climate change prevention goals. At the same time, electricity sectors across the globe are undergoing a rapid transformation in order to accommodate the growing capacities of non-dispatchable solar and wind generators. One of the proposed solutions to achieve heating sector decarbonization and non-dispatchable generators power system integration is sector coupling, where heat pumps are perceived as a perfect fit. Air source heat pumps enable a rapid improvement in local air quality by replacing conventional heating sources, but at the same time, they put additional stress on the power system. The emissions associated with heat pump operation are a combination of power system energy mix, weather conditions and heat pump technology. Taking the above into consideration, this paper presents an approach to estimate which of the mentioned factors has the highest impact on heat pump emissions. Due to low air quality during the heating season, undergoing a power system transformation (with a relatively low share of renewables) in a case study located in Poland is considered. The results of the conducted analysis revealed that for a scenario where an air-to-water (A/W) heat pump is supposed to cover space and domestic hot water load, its CO2 emissions are shaped by country-specific energy mix (55.2%), heat pump technology (coefficient of performance) (33.9%) and, to a lesser extent, by changing climate (10.9%). The outcome of this paper can be used by policy makers in designing decarbonization strategies and funding distribution.

Experience With a Solar Heating ATES System for a University Building

1994 ◽  
Vol 116 (2) ◽  
pp. 88-93 ◽  
Author(s):  
E. Hahne ◽  
M. Hornberger
Keyword(s):  
Solar Energy ◽  
Heat Pump ◽  
Waste Heat ◽  
Heating System ◽  
Solar Heating ◽  
Coefficient Of Performance ◽  
Solar Collectors ◽  
Power Station ◽  
Heat Demand ◽  
Heat Store

At Stuttgart University, a solar heating system for an office building with laboratories and lecture rooms was installed in 1985. It consists of 211 m2 of unglazed solar collectors, a 1050 m3 water-flooded pebble bed heat store, and a heat pump. Heat can be supplied to the store from the solar collectors or from a power station (as waste heat). The whole system has worked successfully for five years under varied strategies. In the first two heating periods, the heating strategy was aimed to collect as much solar energy as possible. Thus, about 60 percent of the heat demand could be covered by solar energy; but the yearly heat pump coefficient of performance (COP) was only around 2.76. With an improved heat pump, a monthly COP of 3.6 was obtained. Heat losses from the storage amounted to about 20 percent.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

Heat Integration of Absorption Heat Pump in a Milk Powder Dairy

2000 ◽  
Author(s):  
Jens Møller Andersen
Keyword(s):  
Heat Pump ◽  
Waste Heat ◽  
Cooling System ◽  
Milk Powder ◽  
Electricity Consumption ◽  
Heat Pumps ◽  
Heat Integration ◽  
Absorption Heat Pump ◽  
Absorption Cooling ◽  
Absorption Cooling System

Abstract Heat integration with absorption heat pumps requires investigation of many types of plant designs. In this article, it is concluded that in many cases high temperature absorption systems for heat recovery are more economically feasible than absorption systems for cooling purposes. The conclusion is based on a project where the scope was to investigate technical and economical possibilities for heat integration of an absorption heat pump in a milk powder plant. The first idea behind the project was to use the waste heat from the rejected air to drive an absorption cooling system to reduce the electricity consumption for cooling proposes. The model of the plant was based on simulations as a background for a time averaged COP model. It was concluded that an absorption system for generating low temperature steam is more feasible.

scholarly journals A Study on the Performance of a Cascade Heat Pump for Generating Hot Water

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4313 ◽  
Author(s):  
Boahen ◽  
Choi
Keyword(s):  
Heat Exchanger ◽  
Energy Saving ◽  
Heat Pump ◽  
Heat Pumps ◽  
Hot Water ◽  
Research Interest ◽  
Coefficient Of Performance ◽  
Energy Saving Potential ◽  
Heating Capacity

The use of cascade heat pumps for hot water generation has gained much attention in recent times. The big question that has attracted much research interest is how to enhance the performance and energy saving potential of these cascade heat pumps. This study therefore proposed a new cycle to enhance performance of the cascade heat pump by adopting an auxiliary heat exchanger (AHX) in desuperheater, heater and parallel positions at the low stage (LS) side. The new cascade cycle with AHX in desuperheater position was found to have better performance than that with AHX at heater and parallel positions. Compared to the conventional cycle, heating capacity and coefficient of performance (COP) of the new cascade cycle with AHX in desuperheater position increased up to 7.4% and 14.9% respectively.

scholarly journals Possibility of Calcium Oxide from Natural Limestone Including Impurities for Chemical Heat Pump

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 803
Author(s):  
LanXin Lai ◽  
Toshio Imai ◽  
Motohiro Umezu ◽  
Mamoru Ishii ◽  
Hironao Ogura
Keyword(s):  
Heat Pump ◽  
Calcium Oxide ◽  
Waste Heat ◽  
Heat Pumps ◽  
Raw Material ◽  
Hydration Reaction ◽  
Chemical Heat ◽  
Chemical Heat Pump ◽  
Thermogravimetric Analyzer ◽  
Save Energy

Improving energy recycle is an important way to save energy resources and preserve the global environment. Chemical heat pump (CHP) is a technology for saving energy, which utilizes chemical reactions to store thermal energy such as waste heat and solar heat, then release it to provide heat for heating/cooling/refrigeration. For a practical CHP, it is necessary to find cheaper and more stable supply materials. In order to evaluate the possibility of calcium oxide from natural Ofunato natural limestone including impurities, we compare Ofunato limestone with Kawara natural limestone and Garou natural limestone from Japan. These calcium oxides worked as a reactant for CaO/H2O/Ca(OH)2 CHP by repeated hydration/dehydration reaction cycle experiments in a thermogravimetric analyzer. As a result, Ofunato CaO exhibits a high hydration reaction rate after decarbonization at 1223 K for 5 h. The reactivity increased by the repeated hydration reaction although the first hydration rate was low. Furthermore, the sintering of impurities in Ofunato limestone occur easier than that in Kawara limestone with lower impurities. The impurities adhered to the surface of the CaO particle to make specific surface area of CaO particle smaller, which could inhibit hydration reaction of CaO particle. Even if Ofunato limestone contains some impurities, it can be utilized as a raw material for chemical heat pumps.

Sign in / Sign up

Export Citation Format

Share Document