scholarly journals Energy and Emission Characteristics of Biowaste from the Corn Grain Drying Process

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4383 ◽  
Author(s):  
Grzegorz Maj ◽  
Joanna Szyszlak-Bargłowicz ◽  
Grzegorz Zając ◽  
Tomasz Słowik ◽  
Paweł Krzaczek ◽  
...  

This paper presents the results of the evaluation of the energy potential of waste from the process of drying corn grain in the form of corn cobs, damaged grains, corn grain husks, and mixtures of starting materials. A technical and elementary analysis was performed for the biomass under investigation. The elemental composition of ash and the tendencies for slagging and boiler slagging were determined, and the emission factors were estimated based on the elemental analysis performed. The tests showed the highest calorific value among the starting materials for corn cobs (CCs) (14.94 MJ·kg−1) and for the mixture of corn cobs with corn husk (CC–CH) (13.70 MJ·kg−1). The estimated emission factors were within ranges of 38.26–63.26 kg·Mg−1 for CO, 936–1549 kg·Mg−1 for CO2, 0.85–4.32 kg·Mg−1 for NOx, 0.91–1.03 kg·Mg−1 for SO2, and 3.88–54.31 kg·Mg−1 for dust. The research showed that the creation of mixtures from starting materials leads to materials with lower potential for negative environmental impact as well as a reduced risk of slagging and fouling of biomass boilers. However, taking into account all the parameters determined for the biomass under study, the highest energy potential was characteristic for corn cobs and the mixture of corn cobs with corn husk.

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1290 ◽  
Author(s):  
Grzegorz Zając ◽  
Grzegorz Maj ◽  
Joanna Szyszlak-Bargłowicz ◽  
Tomasz Słowik ◽  
Paweł Krzaczek ◽  
...  

The paper presents the results of a study on chemical composition of ashes from three types of waste biomass in terms of fertilizer usefulness. Waste from the process of corn grain drying, including corn cobs, corn grains and corn husk and their mixtures in the ratio 4:1 (v/v) were examined. The study proved that corn grain was the material with the highest concentration of macroelements among those studied (P—21,452 ppm, K—25,970 ppm, S—5911 ppm) and the mixture of corn cobs with corn grains (Ca—81,521 ppm). When microelements were considered, the highest concentration was recorded for corn cobs (Cu—207 ppm, Mn—844 ppm, Zn—857 ppm) and corn husk (Fe—15,100 ppm). The analysis of toxic elements in the ashes of the biomass studied showed their highest concentration in corn husk ash (Ni—494 ppm, Cr—301 ppm, Pb—42.7 ppm, As—4.62 ppm). The analysis showed that regardless of the type of biomass studied, all ashes were strongly enriched (in relation to the average soil content) with phosphorus and corn husk ash with calcium in particular. A slight enrichment in copper and lead was recorded for all ashes, and moderate or low for the other elements. It was found that the examined ashes from biomass, which is a residue from the drying of maize grain, have a high fertilizer usefulness.


Author(s):  
N. Zanko ◽  
◽  
T. Gaidai ◽  
S. Stepchenko ◽  
N. Nilova

Aim. Investigation of the influence of natural factors on the quality of grain drying in a grain modular dryer. Methods. Experimental studies in operational conditions and graphical modeling of dried grain moisture depending on natural factors. The results. The change in the environmental conditions causes a certain influence on the return of the spent waste dryer to the environment and the processes of drying the grain in it. This causes the production of undried grain and reduced drying efficiency. The influence of natural factors - temperature and humidity, atmospheric pressure and wind speed on the humidity of corn grain during its drying with a single-module grain dryer has been studied. The output of the refrigerant with moisture vapor is carried out through the perforated panels of the dryer circuit and at the same time experiences some resistance from atmospheric pressure. The results show that the reduction of atmospheric pressure helps to reduce the resistance for the exit of the coolant through the surface of the dryer housing. As a result, the coolant in the chamber is more efficiently spent on the grain drying process. This is evidenced by the simultaneous decrease in pressure and humidity of the dried grain The dryer is also affected by the wind: its body experiences cooling, and the drying temperature and drying conditions of the grain deteriorate. Thus, during the research period, the wind speed decreased from 5,3 m / s to 4,4 m / s, and the humidity of the dried grain decreased from 15,2 % to 13,9 %. That is, the reduction of the effect of wind on the surface of the dryer has a positive effect on the drying process of grain. The ambient air is characterized by the moisture present in it. Its reduction in atmospheric air promotes better moisture yield from corn grain and the "filling" of this air moisture: the humidity of the dried grain decreases. The positive temperature of the atmospheric air causes additional thermal action on the dryer and the drying process in it. In this case, the heat supplied to the working chamber of the dryer is more productively used for the drying process: in accordance with the increase in atmospheric air temperature, the humidity of the dried grain decreased from 15,2 % to 13,9 %. Based on the results of experimental studies, graphical dependences of the humidity of dried corn grain on humidity, pressure, temperature and velocity of atmospheric air are constructed. The grain harvester is a system adapter for Conclusions. Conclusions. The process of grain drying and the moisture content of the resulting dried grain of modular grain dryers depends on the influence of objective natural factors. These include, in particular, the weather conditions during the operation of dryers. With an increase in humidity, pressure and air velocity, the quality of drying deteriorates: when the moisture content of the grain decreases from 18,5 ° C to the regulated 14 %, with a single pass through the dryer, the moisture content of the dried grain exceeds the regulated one and vice versa. Drying grain in conditions of positive ambient air temperatures, especially at an air temperature of more than 21 °C, is most favorable for obtaining grain with a moisture content that is significantly less than 14 % and vice versa. Low wind speed, dry and warm atmospheric air with low pressure contribute to the production of dried grain with regulated humidity. For the maximum elimination of the unfavorable influence of natural factors on the quality of operation of modular dryers according to the criterion of the moisture content of dried grain in the conditions of the forest-steppe zone of Ukraine, it is advisable to carry out the drying process in the period from late September to early October.


ForScience ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. e00928
Author(s):  
Carlos Guilherme Lopes Grotto ◽  
Adão Marcos Ferreira Costa ◽  
Carla Jovania Gomes Colares ◽  
Douglas Henrique Pereira

A utilização de biomassas residuais de plantas utilizadas na agroindústria tem sido crescente. O bagaço de cana-de-açúcar se destaca nesse cenário, já que a cultura da planta é muito difundida, gerando grandes quantidades desse resíduo. Neste contexto é necessário entender as características dessa biomassa para poder otimizar a geração de energia. Diante do exposto, o presente trabalho teve como objetivo caracterizar e avaliar o potencial energético da biomassa de cana-de-açúcar por meio da análise dos principais parâmetros que influenciam esse processo. Foram realizadas análises de poder calorífico superior, análises químicas imediatas, infravermelho e análise elementar, com o intuito de avaliar o potencial energético desse material. Observou-se bom nível de poder calorífico superior, 4309,50 kcal kg-1, além de teores baixos de cinzas, 0,95%, fatores que podem explicar a grande utilização da biomassa de bagaço de cana-de-açúcar para a geração de energia direta, principalmente na indústria. Palavras-chave: Resíduos. Cana-de-açúcar. Fonte de energia.   Characterization of sugar cane bagasse biomass with energy views Abstract The use of residual biomass from plants used in agribusiness has been increasing. The sugarcane bagasse stands out in this scenario, since the plant's culture is very widespread, generating large amounts of this residue. In this context, it is necessary to understand the characteristics of this biomass in order to optimize the energy generation. With the above, the present study had as objective characterize and evaluate energy potential of sugarcane biomass through the analysis of the main parameters that influence the process. Analyzes of superior calorific power, immediate chemical analyzes, infrared and elementary analysis were carried out, in order to evaluate the energetic potential of this material. A good level of higher calorific value was observed, 4309.50 kcal kg-1, in addition to low ash content, 0.95%, factors that may explain the great use of sugarcane bagasse for direct energy generation, mainly in industry. Keywords: Waste. Sugarcane. Energy source.


2018 ◽  
Vol 26 ◽  
pp. 00004
Author(s):  
Arkadiusz Ostojski

This paper aims to present municipal sewage sludge (MSS) elementary analysis and energetic potential based on measurement of heat of combustion (higher heating value HHV) and calculation of calorific values (lower heating value LHV). The analysis takes into the consideration water content in sewage sludge, at different utilization stages, in wastewater treatment plants in Gdańsk Wschód and Kościerzyna – Pomeranian Voivodeship. The study yielded the following results (in % dry matter): ash 19÷31 %, C - 31÷36 %, H - 5÷6 %, N - 4÷6 %, O - 28÷32 %, S – 1 %. Calorific value of stabilized sludges in Gdańsk was on average 13.8÷15 MJ/kg. In case of sludges not undergoing digestion from Kościerzyna WWTP, the calorific value was at the level of 17.5 MJ/kg. Thus, sewage sludges are good energy carriers. High water content though is the problem, as it lowers the useful effect of heat. There is no alternative for thermal sewage sludge neutralization, which is in conformity with valid Polish National Waste Management Plan (KPGO 2022).


2017 ◽  
Vol 56 (12) ◽  
pp. 3470
Author(s):  
Carlos Villaseñor-Mora ◽  
Francisco J. Gantes-Nunez ◽  
Arturo Gonzalez-Vega ◽  
Victor H. Hernandez-Gonzalez

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 7058-7073
Author(s):  
Aurel Lunguleasa ◽  
Cosmin Spirchez ◽  
Sorin Radulescu

Making pellets from corn cobs, the goal of this work, was motivated by the abundance of vegetable biomass. Corn is used in both animal and human food. Four pelletizing presses with flat die and different capacities were considered. The influence of the capacity of the pellet mills on the density of the obtained pellets was established by increasing the capacities of the pellet mills to increase the density of the pellets. The waste of crushed corn cobs was used for pelletizing. The energy characteristics of the pellets from corn cobs were determined, with a high calorific value of 20.0 MJ·kg-1 and a calorific density of 19.8 MJ·m-3; these values were much higher than the wood species used currently in combustion. The black and calcined ash contents of 24.7% and 2.3%, respectively, were also obtained. Based on the main properties of experimental pellets, corn cob waste can be regarded as suitable for transformation into pellets with good characteristics. The positive influence of capacity press increase on density of pellets was also highlighted.


2018 ◽  
Vol 6 (11) ◽  
pp. 234-238
Author(s):  
DamgouMani Kongnine ◽  
◽  
Pali Kpelou ◽  
Mazabalo Baneto ◽  
Kossi Napo ◽  
...  

2010 ◽  
Vol 62 (2) ◽  
pp. 387-393 ◽  
Author(s):  
H. Kyllönen ◽  
J. Lehto ◽  
P. Pirkonen ◽  
A. Grönroos ◽  
H. Pakkanen ◽  
...  

Large amounts of wet sludge are produced annually in municipal and industrial wastewater treatment. Already in pulp and paper industry, more than ten million tons of primary sludge, waste activated sludge, and de-inking sludge is generated. Waste activated sludge contains large quantities of bound water, which is difficult to dewater. Low water content would be a matter of high calorific value in incineration but it also has effects on the volume and the quality of the matter to be handled in sludge disposal. In this research waste activated sludges from different pulp and paper mills were chemically characterised and dewatered. Correlations of chemical composition and dewatering properties were determined using multivariate analysis. Chemical characterisation included basic sludge analysis, elementary analysis and analysis of wood-based components, such as hemicelluloses and lignin-derived material. Dewatering properties were determined using measurements of dry solids content, flux and flocculant dosage. The effects of different variables varied according to the response concerned. The variables which were significant regarding cake DS increase in filtration or centrifugation and flocculant dosage needed in filtration were different from those which were significant regarding flux.


Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4985
Author(s):  
Tomasz Dudek

Forest biomass is and will remain a primary source of renewable energy in many EU countries in the coming years. The aim of this study was to determine the energy potential of forest biomass on a regional scale with regard to the needs of its inhabitants in terms of electricity and heat consumption. The study was carried out in south-eastern Poland. Energy potential was calculated based on the determined wood mass and calorific value of wood. The current level of forest biomass acquisition satisfies 4.2% of the needs of the local market in terms of electricity and heat consumption. Taking into account high forest cover of the region (40%), the 60% annual increment of total harvesting, and obtaining biomass at the level of 30% of the total harvesting, waste wood from the forest can meet 58.1% of the needs of the local market in terms of electricity consumption and 14.4% of the need for thermal energy consumption. There is a certain niche in the fuel wood market that is currently unused, presenting the opportunity to develop this sector and generate additional jobs in local markets. However, the increase in obtained forest biomass must be in accordance with the principles of sustainable development.


2020 ◽  
Vol 849 ◽  
pp. 40-46
Author(s):  
Denny Irawati ◽  
David Usman ◽  
Naresvara Nircela Pradipta

In Indonesia, Casuarina montana usually planted as a road shading tree or in the home garden. This tree will be pruned periodically to reduce the amount of the canopy and maintain the beauty of its shape. Pruning biomass usually consists of the tip of the stem, branches, twigs, and leaves. The biomass has potency for energy or chemicals sources. This study aims to know about energy potential of various types of C. montana biomass and charcoal properties in different carbonization temperature. Six types of biomass from pruning waste of C. montana were used as samples. Branch has high potency as α-cellulose source, while bark including twig bark, branch bark, or stem bark have high potency as lignin source. When it is used as direct fuel (firewood), all biomass of C. montana possess quite high calorific value. When it is converted to be charcoal, temperature of 300°C is good for carbonizing the biomass twig, twig bark, branch bark, and stem bark, while biomass branch and stem need temperature of 400°C.


Sign in / Sign up

Export Citation Format

Share Document